Cisco Systems 15530 - page 319

A-103

Cisco ONS 15530 Configuration Guide and Command Reference

78-14227-01, Cisco IOS Release 12.1(10)E2

AppendixA Command Reference

Interface Configuration Commands

The following example shows how to display wave interface information. (See Ta ble A- 14 for field

descriptions.)

Switch# show interfaces wave 10/0

Wave10/0 is administratively up, line protocol is up

Channel: 25 Frequency: 195.1 Thz Wavelength: 1536.61 nm

Splitter Protected: Yes

Receiver power level: -37.30 dBm

Laser safety control: Off

Forward laser control: Off

Osc physical port: No

Wavelength used for inband management: No

Configured threshold Group: None

Section code violation error count(bip1): 0

Number of errored seconds(es): 29

Number of severely errored seconds(ses): 29

Number of severely errored framing seconds(sefs): 0

Number of times SEF alarm raised: 0

Number of times SF threshold exceeded: 0

Number of times SD threshold exceeded: 0

Loopback not set

Last clearing of "show interface" counters 4d03h

Hardware is data_only_port

Set threshold Shows alarm thresholds. The output example shows the

alarm thresholds for signal failure (SF) and signal

degrade (SD).

Section code violation error count (bip1) Shows the number of BIP1 errors.

Number of errored seconds (es) Shows the number of errored seconds.

Number of severely errored seconds (ses) Shows the number of severely errored seconds.

Number of severely errored framing seconds

(sefs) Shows the number of severely errored framing seconds.

Number of times SEF alarm raised Shows the number of times the SEF alarm was raised.

Number of times SF threshold exceeded Shows the number of times the signal failure (SF)

threshold was exceeded.

Number of times SD threshold exceeded Shows the number of times the signal degrade (SD)

threshold was exceeded.

Loopback not set Shows whether loopback is enabled.

Last clearing of “show interface” counters Shows the last time “show interface” counters were

cleared.

Hardware is transparent Shows the hardware type.

TableA-13 show interfaces transparent Field Descriptions (continued)

Field Description

TableA-14 show interfaces wave Field Descriptions

Field Description

Wave10/0 is administratively up Shows the interface state, either up or down.

line protocol is up Shows the state of the line protocol, either up or

down.

Contents

Main Page CONTENTS Page Page Page Page Page Page Page Page Page Page Page Preface Audience Organization Related Documentation Document Conventions Obtaining Documentation Documentation CD-ROM Ordering Documentation Documentation Feedback Obtaining Technical Assistance Technical Assistance Center Cisco TAC Website Cisco TAC Escalation Center Obtaining Additional Publications and Information Obtaining Documentation Documentation CD-ROM Ordering Documentation Documentation Feedback Obtaining Technical Assistance Cisco TAC Website Opening a TAC Case TAC Case Priority Definitions Obtaining Additional Publications and Information Page Product Overview Cisco ONS 15530 Hardware Features Chassis Overview 1-2 Cisco ONS 15530 Configuration Guide and Command Reference 78-14227-01, Cisco IOS Release 12.1(10)EV2 Component Summary The Cisco ONS15530 supports the following hot-swappable modular hardware comp onents: uplink cards. FASTENERS MUST BE FULLY ENGAGED PRIOR TO OPERATING THE POWER SUPPLY FAIL 100-240V 8.0-3.5A 50-60HZ L ESCON Multiplexing Line Cards, 10-Gbps ITU Trunk Cards, and 10-GE Uplink Cards Transponder Line Cards OADM Modules Carrier Motherboards OSC Modules VOA Modules PB-OE Modules CPU Switch Modules Switch Fabric Cisco ONS 15530 Software Features Network Management Systems Optical Supervisory Channel In-Band Message Channel Online Diagnostics Network Topologies Standards Compliance Page Before You Begin About the CLI About Cisco IOS Command Modes Page Listing Cisco IOS Commands and Syntax Interface Naming Conventions ESCON Multiplexing Line Card Interfaces Esconphy Interfaces Portgroup Interfaces 10-Gbps ITU Trunk Card Interfaces Ethernetdcc Interfaces Waveethernetphy Interfaces Waveethernetphy Subinterfaces 10-GE Uplink Card Interfaces Ethernetdcc Interfaces Tengigethernetphy Interfaces Tengigethernetphy Subinterfaces Transponder Line Card Interfaces Transparent Interfaces Wave Interfaces OADM Module Interfaces Filter Interfaces Oscfilter Interfaces Wdm Interfaces Thru Interfaces OSC Card Interfaces Wave Interfaces CPU Switch Module Interfaces NME Interfaces Auxiliary Port Interfaces WB-VOA Card Interfaces Voain Interfaces Voaout Interfaces PB-OE Module Interfaces Voafilterin Interfaces Voafilterin Subinterfaces Voafilterout Interfaces Voabypassout Interfaces Voabypassin Interfaces Configuration Overview Page Initial Configuration About the CPU Switch Module Starting Up the Cisco ONS 15530 Using the Console Ports, NME Ports, and Auxiliary Ports Modem Support About Passwords Enable Password Enable Secret Password Configuring IP Access on the NME Interface Page Displaying the NME Interface Configuration Displaying the Operating Configurations Configuring the Host Name About NTP Configuring NTP Displaying the NTP Configuration About CPU Switch Module Redundancy Page Page Redundant Operation Requirements Conditions Causing a Switchover from the Active CPU Switch Module Configuring CPU Switch Module Redundancy Forcing a Switchover from Privileged EXEC Mode Forcing a Switchover from ROM Monitor Mode Configuring Autoboot Displaying the Autoboot Configuration Synchronizing the Configurations Synchronizing Configurations Manually Enabling and Disabling Automatic Synchronization Configuring Maintenance Mode Displaying the CPU Switch Module Redundancy Configuration and Status 3-18 Examples The following example shows the CPU switch module redundancy configuration and status: The following example shows the CPU switch module capabilities: 3-19 Reloading the CPU Switch Modules Configuring Privileged EXEC Mode Access on the Standby CPU Switch Mod ule Displaying the Standby CPU Switch Module Privileged EXEC Mode Status About the Software Configuration Register Software Configuration Register Settings Boot Field Values Default System Boot Behavior Boot Command Changing the Software Configuration Register Verify the Configuration Register Value Page Configuring ESCON Signal Aggregation About ESCON Signal Aggregation Support 4-2 Figure4-1 Interface Model for ESCON Aggregation To configure ESCON support on the Cisco ONS 15530, perform the following steps: Configuring ESCON Multiplexing Line Card Interfaces Displaying the ESCON Multiplexing Line Card Interface Configuration 4-4 The following example shows how to display the configuration of an esconphy in ter face: The following example shows how to display the configuration of a portgroup i nte rface : Configuring 10-Gbps ITU Trunk Card Interfaces Displaying the 10-Gbps ITU Trunk Card Interface Configuration 4-7 The following example shows how to display the configuration of a waveethernetphy subinterfac e: The following example shows how to display the configuration of a wavepatch interface : Configuring 10-GE Uplink Card Interfaces 4-9 Displaying the 10-GE Uplink Card Interface Configuration Displays the interface configuration. To display the configuration of 10-GE uplink card interfaces, use the following EXEC command: show interfaces {tengigethernetphy slot/0[.subinterface] | wavepatchslot/0/port} 4-10 About Cross Connections Configuring Cross Connections Displaying the Cross Connection Configuration About Alarm Thresholds Configuring Alarm Thresholds Displaying the Alarm Threshold Configuration About Patch Connections Configuring Patch Connections Displaying Patch Connections Configuring Transponder Line Card Interfaces Configuring Protocol Encapsulation or Clock Rate Page Page Displaying Protocol Encapsulation or Clock Rate Configuration About Transponder Line Card Channel Frequencies Configuring Transponder Line Card Channel Frequency Displaying Transponder Line Card Channel Frequency About Protocol Monitoring Configuring Protocol Monitoring Displaying Protocol Monitoring Configuration About Alarm Thresholds Configuring Alarm Thresholds Page Displaying Alarm Threshold Configuration About Laser Shutdown About Forward Laser Control About OFC About Laser Safety Control Configuring Laser Shutdown Configuring Forward Laser Control Displaying Forward Laser Control Configuration Configuring Laser Safety Control Displaying Laser Safety Control Configuration Configuring Optical Power Thresholds Displaying Optical Power Threshold Configuration About Patch Connections Configuring Patch Connections Displaying Patch Connections About Cross Connections Displaying Cross Connections Page Page Configuring VOA Module Interfaces About Variable Optical Attenuation VOA Modules Single WB-VOA Modules Dual WB-VOA Modules Single Band PB-OE Modules Dual Band PB-OE Configuring VOA Module Interfaces Configuring Attenuation Displaying the Attenuation Configuration 6-6 The following example shows how to display the attenuation configuration of a voain in te rface : About Optical Thresholds Configuring Optical Receive Power Thresholds Displaying the Optical Threshold Configuration 6-8 The following example shows how to display the threshold configuration of a voain interface: Configuring APS About APS About Splitter Protection Page Considerations for Using Splitter Protection Configuring Splitter Protection Displaying the Splitter Protection Configuration 7-6 The following example shows how to display the APS splitter protection configuration: About Line Card Protection Client based protection Y-cable protection Switch fabric based protection 7-7 About Client Based Line Card Protection Figure 7-3 shows an example of line card protection using transponder line cards. - About Y-Cable Line Card Protection Considerations for Using Y-Cable Based Line Card Protection Configuring Y-Cable Based Line Card Protection Displaying the Y-Cable Protection Configuration 7-12 About Switch Fabric Based Line Card Protection Considerations for Using Switch Fabric Based Line Card Protection Configuring Switch Fabric Based Line Card Protection Displaying Switch Fabric Based Protection Configuration About Redundant Switch Fabric Protection Configuring APS Group Attributes Configuring Revertive Switching Displaying the Revertive Switching Configuration About Unidirectional and Bidirectional Path Switching Page Configuring Unidirectional and Bidirectional Path Switching Page Displaying the Unidirectional and Bidirectional Path Switching Configuration Configuring the Switchover-Enable Timer Displaying the Switchover-Enable Timer Configuration About Switchovers and Lockouts Requesting a Switchover or Lockout Displaying Switchover and Lockout Request Status Clearing Switchovers and Lockouts Displaying Switchover and Lockout Clear Status Configuring Multiple Shelf Nodes About Multiple Shelf Nodes Configuring Multiple Shelf Nodes Configuring Patch Connections Between Shelves Configuring APS Page 8-5 The following example shows how to configure channels 1720 on shelf 2 of a multi ple shelf node. Page Monitoring Your Network Topology About the OSC Hardware Guidelines for Using OSC Configuring CDP Configuring Global CDP Displaying the Global CDP Configuration Displaying Global CDP Information Clearing Global CDP Information Configuring CDP Topology Discovery on Wdm Interfaces Displaying CDP Information for Wdm Interfaces Configuring OSCP Configuring the Hello Interval Timer Configuring the Hello Hold-Down Timer Configuring the Inactivity Factor Displaying the OSCP Configuration Displaying OSCP Neighbors Configuring IP on the OSC Page 9-11 Displaying the OSC Configuration show interfaces wave slot/subcard Displays the OSC wave interface configuration. To display the OSC configuration, use the following EXEC command: The following example shows the OSC configuration: Verifying Connectivity on the OSC Configuring IP on Ethernetdcc Interfaces for the In-Band Message Channel Page Displaying the Ethernetdcc Interface Configuration Verifying Connectivity over the In-Band Message Channel Configuring SNMP Enabling MIB Notifications Alarm Threshold MIB APS MIB CDL MIB Optical Monitor MIB OSCP MIB Patch MIB Physical Topology MIB Redundancy Facility MIB Monitoring Without the OSC or In-Band Message Channel Setting up Connections to Individual Nodes Manually Configuring the Network Topology Displaying the Network Topology Configuring Interfaces in the Network Topology Displaying Topology Information for Interfaces About Embedded CiscoView Installing and Configuring Embedded CiscoView 9-24 Examples 9-25 The following example shows how to update the CiscoView files on your Cisco ONS 15530: Accessing Embedded CiscoView Displaying Embedded CiscoView Information Managing Your Cisco ONS 15530 System Accessing and Displaying File System Devices Using Flash Memory Formatting CompactFlash Cards Copying the Startup Configuration Files to Flash Memory Copying Files Between Flash Memory Devices Viewing the Contents of Flash Memory Determining the Current File System Device Moving Between Flash Memory Devices Listing the Flash Memory Directory Contents Deleting Files from Bootflash Memory Copying a System Image from a TFTP Server to Flash Memory Booting from a CompactFlash Card Accessing System Images on TFTP Servers Booting from a TFTP Server Page 10-9 Figure 10-1 shows a simple network configuration with a TFTP server, a router, a hub, and a The following example shows how to configure the network example shown in Figure 10-1. 10-10 The following example shows how to configure the network example shown in Figure 10-3 with a VLAN. Backing Up a System Image to a TFTP Server Updating System Images Downloading System Images from Cisco.com Copying System Images to the Cisco ONS 15530 Manually Booting the Cisco ONS 15530 10-14 Updating System Images on Redundant Processors Updating with Hot-Standby Compatible System Images Page Updating with Non-Hot-Standby Compatible System Images Page Updating Functional Images Understanding Functional Images Updating a CPU Switch Module Functional Image Release Determining the CPU Switch Module Functional Image Release Version Updating a CPU Switch Module Functional Image from a TFTP Server Page Updating a CPU Switch Module Functional Image from an FTP Server Page Updating Line Card Functional Images Determining the Line Card Functional Image Version Copying a Line Card Functional Image from a TFTP Server to Flash Memory Copying a Line Card Functional Image from an FTP Server to Flash Memory Updating the Line Card Functional Image Updating Module Functional Images Determining the Module Functional Image Version 10-30 Step2 Switch# delete {bootflash: | disk0:}filename (Optional) Deletes a file from Flash memory. Copying a Module Functional Image from a TFTP Server to Flash Memory To download a module functional image from a TFTP server, perform the following steps: Step1 Switch# show {bootflash: | disk0:} Verifies that space is available in Flash memory on the active CPU switch module. If space is available, continue to Step3. Copying a Module Functional Image from an FTP Server to Flash Memory Page Updating the Module Functional Image Page APPENDIX A Command Reference APS Commands aps clear aps direction A-4 Page aps disable aps enable aps lockout aps message-channel Page aps protection Page aps revertive Page aps switch Page aps timer message holddown Page aps timer message max-interval Page aps timer search-for-up Page aps timer switchover-enable min-interval Page aps timer wait-to-restore Page aps working Page aps y-cable Page associate group Page associate interface Page show aps Page Page A-38 Page Page show aps trace Page Debug Commands debug aps debug cdl defect-indication debug cm debug cpu debug diag online debug driver control ethernet debug driver escon debug driver nvram debug driver osc debug driver src debug driver ten-gigabit trunk debug driver voa debug oscp Page debug ports Page debug redundancy Page debug switch debug topology Page undebug all Interface Configuration Commands cdl defect-indication force hop-endpoint cdl enable cdl flow identifier clock rate Page connect Page encapsulation Page Page laser control forward enable Page laser control safety enable laser frequency laser shutdown loopback Page monitor enable Page optical attenuation optical threshold power receive Page Page patch Page show cdl defect-indication Page show connect Page Page Page show controllers Page Page A-99 TableA-11 show controllers Command Field Descriptions for Transparent Interfaces (continued) Field Description Page show interfaces Page Page Page Page Page show optical filter Page Page show patch Page shutdown Page Online Diagnostics Commands diag online diag online slot show diag online Page show diag online detail A-119 Page show diag online slot Page OSCP Commands clear oscp Page oscp timer hello holddown Page oscp timer hello interval oscp timer inactivity-factor Page show oscp info Page show oscp interface Page show oscp neighbor Page show oscp statistics Page show oscp traffic Page CPU Switch Module Redundancy Commands auto-sync running-config Page auto-sync startup-config Page clear redundancy maintenance-mode Page redundancy redundancy manual-sync Page redundancy reload peer redundancy reload shelf redundancy switch-activity show redundancy Page Page Page show redundancy capability A-158 Page show redundancy clients Page show redundancy counters Page show redundancy history Page show redundancy running-config-file Page show redundancy states Page Page standby privilege-mode enable SNMP Commands snmp-server enable traps aps snmp-server enable traps cdl Page snmp-server enable traps optical monitor min-severity Page snmp-server enable traps oscp snmp-server enable traps rf snmp-server enable traps threshold min-severity Page snmp-server enable traps topology Page snmp-server host Page Page Page System Management Commands clear facility-alarm reload Page reprogram Page show bootvar Page show ciscoview package Page show ciscoview version show facility-alarm status Page show hardware Page Page show optical wavelength mapping A-203 TableA-40 show optical wavelength mapping Field Descriptions show temperature Page show version Page Page traceroute Page Page Page Threshold Commands aps trigger Page description notification-throttle timer show threshold-list Page threshold Page threshold-group Page threshold-list Page value Page Topology Neighbor Commands show topology Page show topology neighbor Page topology hold-time topology neighbor Page topology neighbor agent ip-address Page topology neighbor cdp Page topology neighbor disable INDEX Numerics A B C D E F G H I L M N O P Q R S T U V W Y