Manuals / Digi / Musical Instruments & Equipment / DJ Equipment

Digi NS7520 manual MII Management Read Data register bit definition, MII read data

Models: NS7520

1 332

Download 332 pages 47.95 Kb

Page 210

Image 210

E F E c o n f i g u r a t i o n

MII Management Read Data register

Address: FF80 0430

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16

							Reserved

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0

							MII read data

Register bit assignment

Bits	Access	Mnemonic	Reset	Description

D31:16	N/A	Reserved	N/A	N/A

D15:00	R	MRDD	N/A	MII read data
				Provides read data following an MII management
				read cycle.

An MII management read cycle is executed by loading the PHY Address register, then setting the READ bit in the MII Indicators register (see page 197) to 1. Read data is available after the BUSY bit in the MII Indicators register returns to 0.

Table 74: MII Management Read Data register bit definition

1 9 6

N S 7 5 2 0 H a r d w a r e R e f e r e n c e , R e v . D 0 3 / 2 0 0 6

Page 210

Image 210

Digi NS7520 manual MII Management Read Data register bit definition, MII read data

Contents

NS7520 Hardware Reference Page Part number/version 90000353D Release date March Page Contents A p t e r 4 B B u s M o d u l e A p t e r 7 M e m o r y C o n t r o l l e r M o d u l e A p t e r A p t e r 1 0 S e r i a l C o n t r o l l e r M o d u l e D e About this guide Who should read this guideWhat’s in this guide Conventions used in this guideTo read about See Customer support Documentation updatesRelated documentation For Contact informationPage About the NS7520 NS7520 Features Key features and operating modes of the major NS7520 modulesO u t t h e N S 7 5 2 7 5 2 0 F e a t u r e s NS7520 module block diagram NS7520 overviewOperating frequency Pinout and Packaging NS7520 packaging dimensions Symbol Min Nom MaxPackaging NS7520 pinout and dimensions NS7520 BGA layout Pinout detail tables and signal descriptions Column DescriptionSystem bus interface pinout Symbol Pin DescriptionSystem bus interface External busADDR5 ADDR7ADDR6 ADDR4Do not USE Signal descriptions System bus interface signal descriptionMnemonic Signal Description Chip select controller Chip select controller pinoutBusy Chip select controller signal description Mnemonic SignalEthernet interface MAC Ethernet interface MAC pinoutEthernet interface MAC signal description COL CRSSerial Other Pin Serial channel Signal Description No connect pinsNo connect pins General-purpose I/OPORTA2 Dsra Amux RTS PORTC4 RXCB/RIB ResetPORTA3 Rxda DACK1 DSROther signal Gpio signalSerial signal Serial channel Other DescriptionSystem clock and reset Clock generation and reset signal descriptionSystem clock pinout Plltst System mode test supportSystem mode and system reset pinout BistenARM debugger signal description Jtag test ARM debuggerJtag test pinout Trst termination Signal Pin Description Power supplyPower supply pinout GNDWorking with the CPU ARM Thumb concept CPU performanceARM performance ARM modeWorking with ARM exceptions ARMSummary of ARM exceptions Exception prioritiesException vector table Exception vector tableVector Description Address Reset exception Detail of ARM exceptionsUndefined exception SWI exception Abort exceptionIRQ exception Firq exceptionEntering and exiting an exception software action Entering an exceptionExiting an exception Exception entry/exit by exception type Reset UndefException entry/exit summary Abort PHardware Interrupts Firq and IRQ linesInterrupt controller Interrupt sources W . d i g i . c o m Page BBus Module BBus masters and slaves BBus masters and slavesCycles and BBus arbitration Module Master SlaveAddress decoding BBus address decodingAddress range Module Page SYS Module Signal description Signal mnemonic Signal name DescriptionJtag support ARM debug System clock generation NS7520 clock moduleExternal oscillator vs. internal PLL circuit Using the external oscillator NS7520 clock module block diagramExternal oscillator mode hardware configuration Using the PLL circuit PLL mode hardware configurationPLL mode hardware configuration PLL Settings register bit definition Setting the PLL frequencyPLL Settings register Setting the PLL frequency on bootup Bits Access Mnemonic Reset Description D3109 ReservedOutput divider Bits Access Mnemonic Reset DescriptionMHz A87 A65 A40 ND+1 PLL Settings reg PLL multiplierMHz A87 A65 A40 ND+1 PLL Settings reg PLL Control register bit definition PllcntSysclk frequency ND+1 PLL Settings register MHzReset circuit sources NS7520 bootstrap initialization Address bit Name DescriptionGEN Module GEN module hardware initialization Module configurationGEN module address configuration Address RegisterAddress FFB0 GEN module registersSystem Control register General informationSoftware watchdog reset/interrupt select Bclk output disableSoftware watchdog enable Software watchdog timeout in secondsBus monitor enable Enable access to internal chip registers in CPUUser mode DMA module test mode Bits Access Mnemonic ResetDescription Enable ARM CPU Bus interface TEA/LAST configurationCPU disable DMA module resetTA input synchronizer System Status register bit definition Last reset caused by external resetSystem Status register NS7520 revision IDLast reset caused by software reset Last reset caused by watchdog timerLast reset caused by PLL update Product ID defined by external resistor jumpersSoftware Service register bit definition Software Service registerTimer Control registers Address FFB0 000CTimer interrupt enable Timer Control registers bit definitionTimer enable Timer interrupt modeTimer prescaler Timer clock sourceInitial timer count Timer interrupt pending Timer Status registersTimer Status registers bit definition Current timer countPorta register bit definition Porta Configuration registerPorta mode configuration Porta data directionAdata Porta ConfigurationPorta configuration Porta data registerOutputs PORTA1 Gpio Gpio OUT SER1CTS DONE1OUT PORTA0 SER1SPISENABLEInputs IN/SER1DCDPortc register bit definition Portc Configuration registerPortc mode Portc data directionCdata Portc configurationPortc configuration Portc data registerPORTC1 Gpio Gpio OUT LEVELIRQ1=CDIR1 PORTC0 LEVELIRQ0=CDIR0 Interrupts PORTC30Interrupt controller registers Address FFB0 0030 / 0034Interrupt Enable registers bit definition D01 Page Memory Controller Module Mode A2714 A130 CSx Pin configurationMEM module pin configuration by memory type About the MEM moduleMode A2714 A130 SdramRAS CAS Memory controller register map MEM module configurationSetting the chip select address range Address Mnemonic RegisterMemory Space Mmcr bit definition Memory Module Configuration registerEnable Dram refresh Refresh count valueRcyc Enable external address multiplexingEnable A27 output Refresh cycle countEnable A25 output A27 and A26 bit settingsEnable A26 output AMUX2Base Chip Select Base Address registerChip Select Base Address register bit definition Base addressDram configuration mode Peripheral page sizeDram address multiplexer select Burst memory cycle enable External TA configurationDram internal address multiplexer mode Force Bclk at end of memory cycleWrite-protect the chip select EepromValid bit Mask Chip Select Option Register aChip Select Option Register a bit definition Mask AddressWhen DRSEL=0 When DRSEL=1 and DMODE=2’b00When DRSEL=1 and DMODE=2’b01 at full speed Bsize When DRSEL=1 and DMODE=10Burst access size in beats Port sizeOE Ctrl Read cycle modeWrite cycle mode WE CtrlChip Select Option Register B Chip Select Option Register B bit definitionStatic memory Sram controller SyncSingle cycle read/write Sync Write Sync ReadBurst cycles Async ReadUsing the internal multiplexer NS7520 Dram address multiplexing000 001 010 011 100 101 110 111 7 5 2 0 D R a M a d d r e s s m u l t i p l e x i n g Internal Dram multiplexing Mode NS7520 multiplexed address outputsDram Using the external multiplexer Dram refresh FP/EDO Dram controllerNormal FP Dram bus cycles FP Dram Write FP Dram ReadFP/EDO Dram burst cycles FP Dram burst cyclesX32 Sdram configuration NS7520 Sdram interconnectX32 Sdram interconnect BA0 X16 Sdram configurationBA1 BA1 Bclk CLK VCC CKECAS3 RAS CAS2 CAS1 CAS0 NS7520 signal 16M Sdram signal 64M Sdram signalX16 Sdram interconnect UdqmX8 Sdram interconnect X8 Sdram configurationsNS7520 signal 16M Sdram signal Bclk CLK VCC CKESdram A10/AP support Mux mode X32 X16 Command definitionsSdram command definitions CommandMemory timing fields Sdram Bsize configurationCAS latency Bcyc configuration Burst lengthFull Sdram Mode registerSdram Mode register settings Address Field ValueSdram read cycles Sdram normal readSdram burst read Sdram write cycles Sdram normal writeSdram burst write Peripheral page burst size ExampleWait Bcyc Page DMA Module DMA module Fly-by operation transfersMemory-to-memory operation DMA fly-by transfersDMA buffer descriptor Fly-by mode DMA buffer descriptorBuffer descriptor bit definitions Buffer descriptor bit definitionsBit Description Buffer descriptor field definitions Buffer descriptor field definitionsField Description Channel Base address DMA channel peripheral Fly-by mode DMA channel assignmentsDMA channel assignments DMA channel registers Address mapAddress Description Address Description Buffer Descriptor Pointer register DMA Control registerDMA Control register bit definition DMA channel enableDMA operation mode Channel abort requestBurst transfer enable Memory-to-memory modeBTE REQ Channel request sourceDinc SincSource address increment Destination address incrementData operand size Current DMA channel state shown in binaryCurrent DMA channel buffer descriptor index Error completion interrupt pending DMA Status/Interrupt Enable registerDMA Status/Interrupt Enable register bit definition Normal completion interrupt pendingError completion interrupt enable Premature complete interrupt enableNormal completion interrupt enable Buffer not ready interrupt enableEthernet transmitter considerations Ethernet receiver considerations External peripheral DMA supportMemory-to-memory mode Signal descriptionExternal DMA configuration Signal DescriptionDMA controller reset Hardware needed for external memory-to-memory DMA transfersPage Ethernet Module Ethernet front-end EFE FifoTransmit and receive FIFOs EFE transmit processingEFE receive processing Receive buffer descriptor selection DMAExternal CAM filtering MAC module block diagram MAC moduleOther modules in the diagram include EFE configuration EFE register mapAddress Register Register description Test MaxfSupp McfgErxetx Erxdmaetxdma Erxlngetxwm Erxshtefulld Erxbad Ethernet General Control register Egcr bit definitionsAddress FF80 Erxregetxreg Erfifohetfifoh ErxbretxbcEthernet General Control register bit definition Do not set this bit when operating the Ethernet Enable transmit FifoEnable transmit DMA Receiver in interrupt service modeEnable transmit buffer complete interrupt Enable Transmit Data register ready interruptEnable transmit data Fifo half empty interrupt Enable full-duplex operationPSOS pNA buffer descriptors MAC software resetInvert the transmit clock input Insert transmit source addressExternal interface mode Endec mode and NS7520 pinsEndec control signal cross-reference Mode field Output based on EFE CSR bitEthernet General Status register Egsr bit definitions Ethernet General Status register bit definitionRxfdbrxskip Rxregrtxrege Rxfifohtxfifoh Rxbrtxbc Receive Fifo half full Receive Fifo data availableReceive register ready Receive buffer readyTransmit Fifo half empty Receive buffer skipTransmit register empty Transmit buffer completeAddress FF80 0008 / FF80 000C secondary address Endec status signal cross-referenceEthernet Fifo Data register Writing to the Ethernet Fifo Data registerReading from the Ethernet Fifo Data register Ethernet Transmit Status register bit definition Ethernet Transmit Status registerEthernet Fifo Data register bit definition Fifo data FF80Multicast packet transmitted Packet transmitted OKBroadcast packet transmitted Transmit abort late collisionTxaec TxaedTransmit abort excessive deferral Transmit abort excessive collisionsTxaj TxaurTransmit aborted underrun Transmit abort jumboTransmit packet deferred Transmit CRC errorTxdef TxcrcEthernet Receive Status register TxcolcTransmit collision count Receive carrier event previously seen Ethernet Receive Status register bit definitionReceive buffer size in bytes Receive data violation event previously seenReceive broadcast packet Receive packet has CRC errorReceive packet has dribble bit error Receive multicast packetReceive packet has code violation Receive packet is too longReceive packet is too short MAC Configuration Register RoverReceive overflow MAC Configuration Register 1 bit definition Receive enable RX flow controlPass ALL receive frames MAC Configuration Register 2 bit definition PAD/CRC enable Auto detect pad enableVlan pad enable CRC enablePad operation table PAD operationBack-to-Back Inter-Packet-Gap register Back-to-Back Inter-Packet-Gap register bit definitionBack-to-back inter-packet-gap Non-Back-to-Back Inter-Packet-Gap register bit definition Non-Back-to-Back Inter-Packet-Gap registerAddress FF80 040C Non back-to-back inter-packet-gap partCollision window Collision Window/Collision Retry registerCollision Window/Collision Retry register bit definition Retransmission maximumMaximum Frame register Maximum Frame register bit definitionMaximum frame length PHY Support register PHY Support register bit assignmentTest register Enable Jabber protectionBit mode Address FF80 041CTest backpressure Test pauseShortcut pause quanta Reset MII management MII Management Configuration registerMII Management Configuration register bit definition Clock selectScan increment single scan for read data Clks field settingsScani Clks field Sysclk ratio MHz exampleAutomatically scan for read data MII Management Command registerMII Management Command register bit definition Single scan for read dataMII PHY device address MII Management Address registerMII Management Address register bit definition MII PHY register addressMII Management Write Data register bit definition MII Management Write Data registerAddress FF80 042C MII write dataMII Management Read Data register MII Management Read Data register bit definitionMII read data Read data not valid MII Management Indicators registerMII Management Indicators register bit definition Automatically scan for read data in progressSmii Status register Station Address registersSmii Status register bit definition Station Address Register 2 bit definition Station Address RegisterStation Address Register 1 bit definition Station address octetOCTET4 Station Address Register 3 bit definitionOCTET3 OCTET5Station Address Filter register Address FF80 05C0Station Address Filter register bit definition Address FF80 05D0 Register hash tableMulticast hash table entries and bit definitions Address FF80 05D4HT2 bit definition Address FF80 05D8Address FF80 05DC HT3 bit definitionCalculating hash table entries W . d i g i . c o m Page W . d i g i . c o m Page Serial Controller Module Supported features RTS, CTS, DTR, DSR, DCD, RISerial port block diagram Bit-rate generatorUart mode Serial protocolsSPI mode Operating in Endian modes Fifo managementTransmit Fifo interface Terminology What’s being written ValueProcessor interrupts vs. DMA Receive Fifo interfaceUsing processor interrupts Using DMASPI master mode SignalsConfiguration SPI master transmitter SPI slave mode SPI master receiverSignals SPI slave transmitter SPI slave receiverGeneral-purpose I/O configurations SPI slave mode 0 and 1 two-byte transferConfiguration Operating Mode Serial Port Maximum RateSerial port performance N f i g u r a t i o n Address FFD0 0000 Serial Channel registersSerial Channel 1, 2 Control Register a Serial Channel Control Register aEven parity select Parity enableStick parity Number of stop bitsLocal loopback Enable the transmitter with active CTSRemote loopback General-purpose output 1/General-purposeRequest-to-send active Enable receive DMA requestsData terminal ready active Receiver interrupt conditionReceiver interrupts Receiver interrupt enable bitsEnable transmit DMA requests Transmitter interrupt conditionTransmitter interrupt enable bits Transmitter interruptsSerial Channel 1, 2 Control Register B Address FFD0 0004Serial Channel Control Register B bit definition Rcgt Enable receive character GAP timerSCC mode BitordrEnable active RTS only while transmitting Transmit encodingReceive data encoding Differential Manchester 111. a 1 is Serial Channel 1, 2 Status Register a Address FFD0 0008Character Match2 Serial Channel Status Register a bit definitionCharacter Match1 Character Match3Bgap Buffer GAP timerCharacter GAP timer CgapCurrent data carrier detect state Current ring indicator stateDCD Current data set ready stateReceive framing error interrupt pending Receive parity error interrupt pendingReceive break interrupt pending Receive overrun interrupt pending RrdyReceive register ready interrupt pending Receive Fifo half-full interrupt pending Receive buffer closed interrupt pendingReceive Fifo full Change in DSR interrupt pending Change in DCD interrupt pendingChange in RI interrupt pending Change in CTS interrupt pendingTransmit register empty interrupt pending Transmit Fifo half-empty interrupt pendingTransmit buffer closed interrupt pending Serial Channel 1, 2 Bit-Rate registers Address FFD0 000C / 4CTempty Serial Channel Bit-Rate register bit definition Bit-rate generator enableTiming mode Receive clock sourceTransmit clock source Drive receive clock externalDrive transmit clock external Clkmux BRG input clockTransmit clock invert Receive clock invert When Dpll is used in the application, If Dpll is not used and you are not usingIf Dpll is not used but you are using TdcrRdcr Receive divide clock rateRics TicsTransmit internal clock source Receiver internal clock sourceWith the 18.432MHz crystal using Xtale as the clock source Max baudrates with different clock sourcesNreg With the 18.432MHz crystal using Sysclk as the clock source 16X @ 55.296MHzAddress FFD0 0010 X1 mode X8 mode X16 modeSerial Channel 1, 2 Fifo registers Bit rate examplesData Serial Channel 1, 2 Receive Buffer Gap TimerAddress FFD0 0014 DataSerial Channel Receive Buffer Gap Timer bit definition Serial Channel 1, 2 Receive Character Gap TimerRegister diagram and bit assignment Address FFD0 0018Serial Channel Receive Character Gap Timer bit definition CT valueAddress FFD0 001C / 5C Serial Channel 1,2 Receive Match registerSerial Channel 1, 2 Receive Match Mask register Address FFD0 0020RMMB2 Serial Channel Receive Match Mask register bit definitionRMMB1 RMMB3Page Electrical Characteristics Recommended operating thermal conditions DC characteristicsRecommended operating conditions Sym Parameter Conditions Min Typ Max UnitDC characteristics inputs Input/Output characteristicsPad pullup and pulldown characteristics DC characteristics outputsInternal pullup characteristics Absolute maximum ratings AC characteristicsAC electrical specifications Maximum voltage ratingsPORTA3, PORTA1, PORTC3, PORTC1 Estimated Signal Load pF Device loadsSystem loading details MDC, MDIO, TXEN, TXER, TXD30Output buffer derating by load capacitance Oscillator CharacteristicsSignal Derating ns/pF MDC, TXD30, TXER, TXEN, TDONS7520 Timing Diagrams TimingSpecificationsResettiming Reset timing parametersNum Description Min Typ Max Units Sram timing Sram timing parametersNum Description Min Max Unit Sram read CS* controlled read wait =Sram burst read CS* controlled read wait = 0, Bcyc = Sram write CS controlled write internal and external, wait =Sram burst write Sram OE read OE* controlled read wait =Sram OE burst read Sram WE write WE* controlled write wait =Sram WE burst write Sdram timing Sdram timing parametersSdram read Sdram read, CAS latency =Active Read Inhibit Prechg Bterm Sdram burst read Sdram burst read Sdram write Sdram writeSdram burst write Sdram burst writeSdram load mode Sdram refreshFP Dram timing FP Dram timing parametersFP Dram read Fast Page readFP Dram burst read Fast Page burst readFP Dram write Fast Page writeFP Dram burst write Fast Page burst writeFprefreshcycles Fast page refresh Rcyc =CAS3 CAS2 CAS1 CAS0 RF1 RF2 RF3 RF4 RF5 RF8 Ethernet timing Ethernet timing parametersEthernet PHY timing Ethernet cam timingJtag arm ice timing parameters Jtag arm ice timing diagramJtag timing Num Description Min Max UnitsJtag bscan timing diagram Jtag bscan timing parametersExternal DMA timing External DMA timing parametersFly-by external DMA Memory-to-memory external DMA Serial internal/external timing Serial internal timing characteristicsSerial external timing characteristics 2T SYSSynchronous serial internal clock Synchronous serial external clockGpio timing diagram Gpio timingGpio timing parameters Page Index CPU Non-Back-to-BackInter-Packet-Gap register FP Dram Portc NET+ARM PORTC0 Receiver interrupts 229 transmitter interrupts Undefined exception 32 Page

MII Management Read Data register

Address: FF80 0430

Register bit assignment

Bits

MRDD

MII read data

Table 74: MII Management Read Data register bit definition