MANUAL FINISHING MODE
When the inserter is installed, finishing operations such as stapling or punching can be performed without performing a copy or print operation.
Touch the [MANUAL FINISHING] key to change modes. The following screen will appear. For information on manual finishing functions, see the following pages.
|
|
|
| Set the output function. |
|
|
|
|
|
| ||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| Plain |
|
|
|
|
|
|
(1) |
|
|
|
|
|
|
|
|
| 8½x11 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| Plain |
|
|
|
|
|
| |
(2) |
|
|
|
|
|
|
|
|
| 8½x11 |
|
|
|
|
| Fold |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
|
|
| Top Tray |
|
|
|
|
|
|
|
|
|
|
| ||
|
|
|
|
|
|
|
|
|
|
|
|
| ||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| Offset Tray |
|
|
|
|
|
|
|
|
|
|
|
| ||
(3) |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| 2 Hole |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| Punch | |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| 3 Hole |
(4) |
|
|
|
|
| Staple |
|
|
| Saddle | ||||||
|
|
|
|
|
|
|
| Stitch |
|
|
| Punch | ||||
|
|
|
|
|
|
|
|
|
|
|
|
|
| |||
(5)
(6)
(7)
(1)Inserter (upper tray), inserter (lower tray) key
Use these keys to select the tray that you wish to use for finishing. Load the paper to be used for finishing and then select the tray on which the paper is loaded.
(2)[Top Tray] key
(5)[Saddle Stitch] key
Use this to staple the output at the center and fold it into a booklet.
This sets the top tray as the output tray.
(3)[Offset Tray] key
This sets the offset tray as the output tray.
(4)[Staple] key
(6)[Fold] key
Use this to fold the output in half and then fold one side back.
☞PAPER FOLDING FUNCTION (page 70)
(7)[2 Hole Punch], [3 Hole Punch] key
When selected, three keys appear to let you select the staple position.
Use these to punch holes in output.
☞PUNCH FUNCTION (page 69)
•It may not be possible to use some functions, depending on the peripheral devices that have been installed. If the keys in your screen are not the same as in the above screen, check what devices have been installed.
•While a finishing operation is being performed in manual finishing mode, it is not possible to switch to another mode. Similarly, it is not possible to switch to manual finishing mode during output in another mode.
65