Base Drive Panel Catalog Numbers | Siemens 6RA70 specification

3 Parts and Service

3.1Base Drive Panel Catalog Numbers

US RATING	1-QUAD TYPE	4-QUAD TYPE	Horsepower	Horsepower
(Amps DC)	(Catalog No.)	(Catalog No.)	(240V DC 1)	(500V DC)
15	6RA7013-2FS22-0	6RA7013-2FV62-0	3HP	7.5HP

30	6RA7018-2FS22-0	6RA7018-2FV62-0	7.5HP	15HP

60	6RA7025-2FS22-0	6RA7025-2FV62-0	15HP	30HP

100	6RA7030-2FS22-0	6RA7030-2FV62-0	25HP	60HP

140	6RA7072-2FS22-0	6RA7072-2FV62-0	40HP	75HP

210	6RA7075-2FS22-0	6RA7075-2FV62-0	60HP	125HP

255	6RA7077-2FS22-0	6RA7077-2FV62-0	75HP	150HP

430	6RA7082-2FS22-0	6RA7082-2FV62-0	125HP	250HP

510	6RA7083-2FS22-0	6RA7083-2FV62-0	150HP	300HP

850	6RA7087-2FS22-0	6RA7087-2FV62-0	250HP	500HP

1180(2)	6RA7091-2FS22-0	6RA7091-2FV62-0	350HP	700HP

1660(2)	6RA7094-2FS22-0	6RA7094-2FV62-0	500HP	1000HP

1680(2)	6RA7094-2FS22-085	6RA7094-2FV62-085	500HP	1000HP

1) Standard voltage configuration	2) Standard voltage configuration
as shipped is 460V AC.	as shipped is 460V AC.
See Technical application note	See Technical application note
for 230V AC connection.	for 575V AC connection on 1180
	1660 & 1680A Base drives

Siemens Energy & Automation	3-1
SIMOREG DC Master Base Drive Panel	Operating Instructions

Image 12

Siemens 6RA70 Base Drive Panel Catalog Numbers, US Rating Quad Type, Horsepower Amps DC Catalog No 240V DC 500V DC

Contents

Dc drives Converter software version Contents Faults and Alarms Start-upAbbreviated Parameter List Simplified Block Diagrams Definitions Qualified PersonnelOperating Instructions Siemens Energy & Automation Electro-statically sensitive devices Siemens Energy & Automation Base Drive Panel Description General Information Card Rack Assembly Rated DC Current Horsepower Amps DC Catalog No 240V DC 500V DC Base Drive Panel Catalog NumbersUS Rating Quad Type Service Spare PartsTechnical Assistance 800-333-PIC1 Option Part Numbers Options Order NoEB1, EB2, SBP and SLB boards Description Where Used Part Recom Spare PartsPrinted Circuit Boards Cables Description Where Used Part Number Recom Fans/Blowers Armature Converter Thyristor Modules, for 4-Quad Drives Field Converter Thyristor ModulesField Converter Diode Modules Power Fuses Armature Converter AC Line Fuses, 1PFU 3 PFU Armature Converter DC Fuses, 4-Quad Only, 4PFU Field Converter AC Line Fuses 1 & 2FSFU Control Transformer Primary Fuses 1CFU, 2CFUControl Transformer Secondary Fuse 3CFU Description Control Transformer 1CTR, 2CTR, 3CTR Main Contactor MContactor Coil Suppressor 1SP, Ensp Auxiliary Relay, EN, and Rectifier Bridge, Mrec Standard Terms and Conditions of Sale Siemens Energy & Automation, Inc. Seller Operating Instructions Siemens Energy & Automation Procedure for Shipping Damage Receiving, unpacking Siemens Energy & Automation 15ADC to 100ADC Base Drive Panels, 3AC 460V, 1 & 4Q 100 140ADC to 850ADC Base Drive Panels, 3AC 460V, 1 & 4Q 140 210 255 430 510 850 1180 1660 1680 Ambient temperature Reduction in base drive dc ampere rating Applicable standards Siemens Energy & Automation Installation and Dimensions Installation Information Dimensions are mm inches Base Drive Panel Outlines15 30 AMP Base Drive PANELS, 1 & 4Q AMP Base Drive PANEL, 1 & 4Q Terminals 80 Power Terminals L1 L2 L3 A1 A2 1120 44.1 1100 43.3 AMP Base Drive PANEL, 1 & 4Q AMP Base Drive PANEL, 1 & 4Q 280 11.0 1200 47.2 740 29.1 965 38.0 AMP Base Drive PANEL, 1 & 4Q 965 38.0 Siemens Energy & Automation Base Drive Panel Connections Base Drive Panel Schematics Base Drive PANEL, 15 AMPS, 1 & 4 Quad Base Drive PANEL, 30 AMPS, 1 & 4 Quad Base Drive PANEL, 60 AMPS, 1 & 4 Quad Base Drive PANEL, 100 AMPS, 1 & 4 Quad Base Drive PANEL, 140 AMPS, 1 & 4 Quad INCH- LBS Base Drive PANEL, 210 AMPS, 1 & 4 Quad Base Drive PANEL, 255 AMPS, 1 & 4 Quad Base Drive PANEL, 430 AMPS, 1 & 4 Quad 1CTR Base Drive PANEL, 510 AMPS, 1 & 4 Quad Base Drive PANEL, 850 AMPS, 1 & 4 Quad Base Drive PANEL, 1180 AMPS, 1 & 4 Quad 3CTR Base Drive PANEL, 1660 AMPS, 1 & 4 Quad 2CTR 3CTR Base Drive PANEL, 1680 AMPS, 1 & 4 Quad Catalog no RA7096-4GV62-0Z+X01, 4-QUAD Operating Instructions Control Connections CUD1 CUD Terminal Locations CUD1 Control Connections CUD2 Optional CUD2 Control Connections Terminal Locations CUD2 Description of Power/Control Terminals Base Drive Panel Power Connections 15 to 100 Amp Base Drive Panel Power Connections 430 to 1680 Amp Motor Armature circuit Function Terminal Connection values/Remarks Possible Internally connected to incoming 460 VAC, 3 Phase Siemens Energy & Automation General safety information for start-up Start-Up Operator control panels Simple operator control panel PMU Parameterization Unit User-friendly operator control panel OP1S LED displays Parameterization procedure Parameter typesParameterization on simple operator control panel Operating Instructions Typical Connection Diagrams PMUA1+ A2- 80+ Speed Reset to factory default values and adjust offsets Execution of the default function Start-up procedure Panels Access authorization Adjustment of converter rated currentsAdjustment to actual converter supply voltage Input of motor data Freely wired actual value Operation with pulse encoderPulse encoder type Normal selection Operation without tachometer EMF control Field data Selection of basic technological functions Execution of optimization runs Siemens Energy & Automation Operating Instructions Checking and possible fine adjustment of maximum speed Setting Application FunctionsSource of Start Command P654 = Starting the Drive Speed Setpoint Selection Source of Speed Setpoint P433 = Jog Inching Configuration Source of Jog Command P435 = ValueSource of Jog Setpoint P436 = Value Documentation of setting values Siemens Energy & Automation Fault messages General information about faultsOn the OP1S List of fault messages Further information about the causes of fault messages2.1 Supply faults F001 Failure of electronics power supply Fault Description P078.001 ∗ 100%P353 F006 Undervoltage F007 Overvoltage Interface error Parameter P363F011 Telegram failure at GSST1 USS telegram failure at G-SST1 F012 Telegram failure at GSST2 USS telegram failure at G-SST2Peer-to-peer telegram failure at G-SST2 F013 Telegram failure at GSST3 External faults F016 Hardware fault on expansion board EB1F017 Hardware fault on expansion board EB2 F015 Telegram failure on one Simolink board Fault messages from motor sensors F021 External faultF022 External fault F023 Fault message from free function block FB2 Drive faults F029 Motor overtemperature active in all operating statesP493=2 or 3 temperature sensor at terminals 22 / 23 or P494=2 or 3 temperature sensor at terminals 204 F034 Fault message from free function block FB5 F035 Drive is blockedF038 Overspeed Cause as a function of fault value F042 Tachometer fault Fault Description Start-up faults F050 Fault Description Fault Description Fault Description Fault Description F051 No optimization run when permanent memory is disabled V2.1 and later F058 Parameter settings are not consistent F056 Important parameter is not set Operating Instructions Hardware faults Internal faults Number of faulty parameterR047 Index 002 to Fault F064 Watchdog timer has initiated a resetF067 Converter cooling faulty F063 Communication errors with supplementary boards F069 Mlfb data are faulty active in all operating states F080 Error in initialization of a CB/TB board F081 CB/TB heartbeat errorF082 CB/TB message timeout or error in data exchange F078 Fault messages from supplementary boards F101 to F147 Alarm messages Alarm Description A025 Brush length too short A028 Motor overtemperature active in all operating statesA029 Motor overtemperature active in all operating states A026 Poor bearing condition active in all operating states A034 Alarm message from free function block FB9 A039 I2t value of power section too highA047 Analog select input 1 terminals 6 and 7 faulty A035 Drive blocked Alarm Description A049 SCB1 No SCI slave connected A053 Alarm message from free function block FB258A054 Alarm message from free function block FB259 A067 Converter cooling faulty Siemens Energy & Automation Overview 10-1Simoreg DC Master Base Drive Panel Operating Instructions 10-2 Range of parameter numbers FunctionP899 Parameters for DriveMonitor and OP1S R999 Overview of abbreviations 10-3S00 10-4 Operating status display 10-5 10-6 General visualization parameters 10-7 10-8 10-9 10-10 Access authorization levels 10-11 10-12 Definition of Simoreg DC Master converter 10-13 10-14 R065 Software identifiersP067 Load class R068 Options according to rating plate 10-15 10-16 P077 Total thermal reduction factorTemp = k1 P078 Reduction of converter rated supply voltage Setting values for converter control 10-17P080 Control word for brake control P081 EMF-dependent field weakening Internal field power module External field power module 40.00A field10-18 No field P085 Wait period after cancellation of inching command 10-19P086 Voltage failure period for automatic restart P087 Brake release time 10-20 P090 Stabilization time for line voltageP091 Setpoint threshold P093 Pick-up delay for line contactor P094 Switch-off delay for auxiliaries10-21 P095 Pick-up time for a contactor in the DC circuit Definition of motor 10-22 10-23 Magnetization characteristic field characteristic 10-24 10-25 Example of a field characteristic 10-26 10-27 P142 Matching to pulse encoder signal voltage 10-28Single/multiple evaluation of encoder pulses P140 Selection of pulse encoder type P144 Multiple evaluation of encoder signals 10-29Rev/min FS=500.0 P051 G145 1rev/min Type O4 Online 100% 10-30 10-31 Current limitation, torque limitation 10-32 10-33 Auto-reversing stage, armature gating unit Speed controller10-34 10-35 Closed-loop field current control, field gating unit 10-36 10-37 Closed-loop EMF control 10-38 P295 Mode for rounding the ramp-function generator Ramp-function generator10-39 P296 Ramp-down time of ramp generator with quick stop OFF3 10-40 Setpoint processing 10-41 Setting values for monitoring functions and limits 10-42 Setting values for limit-value monitors 10-43 10-44 Settable fixed values 10-45 Fixed control bits 10-46 10-47 Position sensing with pulse encoder 10-48 Connector selector switches Motorized potentiometer10-49 10-50 Oscillation Definition of Motor interface10-51 Tripping of alarm or fault message P496 Bearing condition Tripping of alarm or fault messageP497 Air flow Tripping of alarm or fault message P498 Temperature switch Tripping of alarm or fault message Configuring of torque shell input Speed limiting controller10-53 Friction compensation 10-54 Compensation of moment of inertia dv/dt injection 10-55 10-56 Speed controller adaptationP550 Gain in the adaptation range P551 Integration time in the adaptation range 10-57 Input quantities for signals Field reversal10-58 Configuring of closed-loop control 10-59 10-60 Speed limiting controller . Both values are addedP602 Source for armature current controller actual value Actual value 10-61 P605 Source for variable positive torque limitP606 Source for variable negative torque limit P607 Source for torque setpoint for master drive 10-62 10-63 10-64 10-65 10-66 Control word, status word 10-67 10-68 10-69 Further configuring measures 10-70P690 Source for control word 2, bit30 P691 Source for control word 2, Bit31 10-71 P707 Resolution of Main setpoint analog input P713 Mode of signal injection at Analog selectable input10-72 P711 Normalization of Analog selectable input 10-73 10-74 Analog outputs 10-75 10-76 Binary outputs 10-77 Configuration of serial interfaces on basic converter 10-78 See Change Access / Status P786 USS bus address for G-SST1 R789 Diagnostic information for G-SST110-79 P787 Telegram failure time for G-SST1 10-80 P792 Length of parameter jobs for G-SST2P793 Baud rate for G-SST2 Ind None P052 = Baud FS=6 P051 = G171 Type O2 Offline G173 See Change Access / Status P795 Options for G-SST2 10-81P796 USS bus address for G-SST2 P797 Telegram failure time for G-SST2 10-82 Violation of telegram residual transfer time USS prot. onlyP801 Number of process data for G-SST3 P802 Length of parameter jobs for G-SST3 See Change Access / Status P803 Baud rate for G-SST3 10-83P804 Source for transmit data for G-SST3 P805 Options for G-SST3 R809 Diagnostic information for G-SST3 10-84P808 See Change Access / Status R810 Receive data on G-SST1 10-85R811 Transmit data on G-SST1 R812 Receive data on G-SST2 10-86 R815 Transmit data on G-SST3 Deactivation of monitoring functions Compensation values10-87 Thyristor diagnosis Parameters for DriveMonitor and OP1SProfile parameters 10-88 Fault memory R947 Fault memoryR949 Fault value R951 Fault text P952 Number of faults Visualization parameters Alarms 10-90 Device identification Visualization parameters Control and status word10-91 R980 List of existing parameter numbers, start R981 List of existing parameter numbers, continuationR982 List of existing parameter numbers, continuation R983 List of existing parameter numbers, continuation 10-93 10-94 Simplified block diagrams Basic functions Sheet 1 Legend Siemens Energy Sheet 2 Speed Setpoint System Sheet 3 Speed Controller and Current Limit Sheet 4 Armature Current Control 11-6 Sheet 5 EMF and Field Current Control Sheet 6 USS USS interfaceInterface 1 Sheet 7 USS Interface 2X172 Sheet 8 Peer to Peer Interface Peer-to-peer interface Sheet 9 Data Exchange CB / TB to Base PZD Sheet WordControl word 11-12 Sheet 11 Control Status Word Status word 11-14 Meaning Signals SignalsSheet 11-16 Sheet 15 Miscellaneous Siemens Energy & Automation, Inc