Siemens 6RA70 specifications Field reversal, Input quantities for signals, 10-58

PNU	Description	Value range	No. indices	See
		[Unit]	Factory	Change
		Steps	setting	(Access /
			Type	Status)

10.32 Field reversal

(see also Section 9 of Operating Instructions 6RX1700-0AD**)

P580	Source for selection of "Direction of rotation reversal using field		All binector numbers	Ind: 2	P052 = 3
*	reversal”		1	FS=0	P051 = 40
BDS	Selection of binector to control the "Direction of rotation reversal using field			Type: L2	Offline
	reversal" function
(G200)	0 = binector B0000
	1 = binector B0001
	etc.
	Signal 0: Positive field direction is selected (B0260 = 1, B0261 = 0),
	actual speed value is not inverted
	Signal 1: Negative field direction is selected (B0260 = 0, B0261 = 1),
	actual speed value is inverted
P581	Source for selection of "Braking with field reversal”		All binector numbers	Ind: 2	P052 = 3
*	Selection of binector to control the ”Braking with field reversal" function		1	FS=0	P051 = 40
BDS				Type: L2	Offline
	0 = binector B0000
(G200)	1 = binector B0001
	etc.
	Signal change 0→1: Reversal of field direction (causes braking);
	When n<n-min is reached, the original field direction is
	selected again. The drive switches to state o7.2
P582	Source for selection of "Field reversal”	[SW 1.9 and later]	All binector numbers	Ind: 2	P052 = 3
*	Selection of binector to control "Field reversal" function		1	FS=0	P051 = 40
BDS				Type: L2	off-line
	0 = binector B0000
(G200)	1 = binector B0001
	etc.
	Signal 0: Positive field direction is selected (B0260 = 1, B0261 = 0)
	Signal 1: Negative field direction is selected (B0260 = 0, B0261 = 1)
P583	Source for actual speed signal for field reversal logic		All connector	Ind: None	P052 = 3
*		[SW 1.9 and later]	numbers	FS=167	P051 = 40
	Selection of connector to be used as actual speed value for the field		1	Type: L2	off-line
(G200)	reversal logic.
	0 = binector B0000
	1 = binector B0001
	etc.

10.33 Input quantities for signals

(see also Section 8, Sheet G187 and G188 of Operating Instructions 6RX1700-0AD**)

P590	Source for setpoint of “nset = nact signal 1”	All connector	Ind: None	P052	= 3
*	Setpoint/actual value deviation signal:	numbers	FS=174	P051	= 40
		1	Type: L2	Offline
(G187)	Selection of connector to be injected as input quantity "nset" for the
	setpoint/actual value deviation signal.
	0 = connector K0000
	1 = connector K0001
	etc.
P591	Source for actual value of "n-set = n-act signal 1"	All connector	Ind: None	P052	= 3
*	Setpoint/actual value deviation signal:	numbers	FS=167	P051	= 40
		1	Type: L2	Offline
(G187)	Selection of connector to be injected as input quantity "nact" for the
	setpoint/actual value deviation signal.
	0 = connector K0000
	1 = connector K0001
	etc.

10-58	SIEMENS Energy & Automation
	SIMOREG DC Master Base Drive Panel Operating Instructions