PNU

Description

Value range [Unit] Steps

No. indices Factory setting Type

See Change (Access / Status)

r011

Display of status of binary outputs

 

 

 

Ind: None

P052 = 3

 

Representation on operator panel (PMU):

 

 

Type: V2

 

(G112)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

(G117)

 

15

14

13

12

 

11

10

9

8

 

 

 

 

 

 

 

7

6

5

4

 

3

2

1

0

 

 

 

 

 

 

 

Segment ON:

Corresponding terminal is activated

 

 

 

(HIGH level is applied) or overloaded or short-circuited

 

 

Segment OFF:

Corresponding terminal is not activated

 

 

 

(LOW level is applied) or not overloaded or not short-

 

 

 

circuited

 

 

 

 

 

 

 

 

Display of status of binary output terminals:

Segment or bit

0..... Terminal 46

1..... Terminal 48

2..... Terminal 50

3..... Terminal 52

7 ..... Terminal 109/110 (relay contact for line contactor)

 

Display of overloading of binary outputs:

 

 

 

 

 

 

Segment or bit

 

 

 

 

 

 

8

Terminal 46

 

 

 

 

 

 

9

Terminal 48

 

 

 

 

 

 

10 ....

Terminal 50

 

 

 

 

 

 

11 ....

Terminal 52

 

 

 

 

 

 

12 ....

Terminal 26 (15V output)

 

 

 

 

 

 

13 ....

Terminal 34, 44 and/or 210 (24V output)

 

 

 

 

 

 

 

 

 

 

 

r012

Motor temperature

 

-58 to +200

 

Ind: 2

P052 = 3

 

Display of motor temperature when a KTY 84 temperature sensor is

[°C]

 

Type: I2

 

 

1°C

 

 

 

(G185)

connected (P490.x=1).

 

 

 

 

 

 

 

 

A value of "0" is always output in r012 when a PTC thermistor or no

 

 

 

 

 

temperature sensor is installed.

 

 

 

 

 

i001:

Motor temperature 1 (sensor at terminals 22 / 23)

 

 

 

 

 

i002:

Motor temperature 2 (sensor at terminals 204 / 205)

 

 

 

 

 

 

 

 

 

 

r013

Heatsink temperature

-47 to +200

 

Ind: None

P052 = 3

 

Display of heatsink temperature

[°C]

 

Type: I2

 

 

1°C

 

 

 

r014

Temperature rise

 

0.0 to 200.0

 

Ind: 2

P052 = 3

 

i001:

Calculated motor temperature rise (see P114)

[%]

 

Type: O2

 

 

0.1%

 

 

 

 

i002:

Calculated thyristor temperature rise (see P075)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

r015

Display of line voltage (armature)

0.0 to 2800.0

 

Ind: None

P052 = 3

 

(generated as arithmetic rectification average, RMS value display applies to

[V]

 

Type: O2

 

 

0.1V

 

 

 

 

sinusoidal voltage, average over 3 line-to-line voltages)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

r016

Display of line voltage (field)

0.0 to 800.0

 

Ind: None

P052 = 3

 

(generated as arithmetic rectification average, RMS value display applies to

[V]

 

Type: O2

 

 

0.1V

 

 

 

 

sinusoidal voltage)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

r017

Display of line frequency

0.00 to 120.00

 

Ind: None

P052 = 3

 

 

 

 

[Hz]

 

Type: O2

 

 

 

 

 

0.01Hz

 

 

 

r018

Display of firing angle (armature)

0.00 to 180.00

 

Ind: None

P052 = 3

(G163)

 

 

 

[degrees]

 

Type: O2

 

 

 

 

0.01degrees

 

 

 

 

 

 

 

 

 

 

r019

Display of actual armature current

-400.0 to 400.0

 

Ind: None

P052 = 3

 

The internal actual armature current value is displayed (arithmetic average

[% of P100]

 

Type: I2

 

(G162)

0.1% of P100

 

 

 

over the last 6 current peaks in each case)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

r020

Display of the absolute value of armature current setpoint

0.0 to 300.0

 

Ind: None

P052 = 3

(G162)

 

 

 

[% of P100]

 

Type: I2

 

 

 

 

0.1% of P100

 

 

 

 

 

 

 

 

 

 

r021

Display of torque setpoint after torque limitation

-400.0 to 400.0

 

Ind: None

P052 = 3

 

 

 

[%]

 

Type: I2

 

(G160)

Steps: 1 = 0.1% of rated motor torque (=rated motor armature current

0.1% (see column on

 

(P100) * magnetic flux at rated motor field current (P102))

left)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

10-8

 

 

 

 

SIEMENS Energy & Automation

 

 

 

SIMOREG DC Master Base Drive Panel Operating Instructions

Page 129
Image 129
Siemens 6RA70 specifications 10-8