Base Drive Panel Connections | Siemens 6RA70 instruction

7 Base Drive Panel Connections

WARNING

Base Drive Panels are operated at high voltages.

Disconnect the power supply before making any connections!

Only qualified personnel who are thoroughly familiar with all safety notices contained in the operating instructions as well as erection, installation, operating and maintenance instructions should be allowed to work on these devices.

Non-observance of the safety instructions can result in death, severe personal injury or substantial property damage.

Failure to make the correct connections may result in irreparable damage to the unit. Voltage may be present at the power and control terminals even when the motor is stopped.

The snubber capacitors may still carry a hazardous voltage for up to 2 minutes after disconnection. For this reason, wait for at least 2 minutes before opening the converter.

When working on the open converter, remember that live parts are exposed. The unit must always be operated with the standard front covers in place.

The user is responsible for ensuring that the motor, SIMOREG Base Drive Panel and other devices are installed and connected up in accordance with the approved codes of practice of the country concerned and any other regional or local codes that may apply. Special attention must be paid to proper conductor sizing, fusing, grounding, isolation and disconnection measures and to overcurrent protection.

These units contain hazardous rotating machinery (fans) and control rotating mechanical components (motors). Death, serious bodily injury or substantial property damage may occur if the instructions in the relevant operating manuals are not observed.

The successful and safe operation of this equipment is dependent on careful transportation, proper storage and installation as well as correct operation and maintenance.

Siemens Energy & Automation	7-1
SIMOREG DC Master Base Drive Panel	Operating Instructions

Image 46

Siemens 6RA70 specifications Base Drive Panel Connections

Contents

Dc drives Converter software version Contents Start-up Faults and AlarmsAbbreviated Parameter List Simplified Block Diagrams Qualified Personnel DefinitionsOperating Instructions Siemens Energy & Automation Electro-statically sensitive devices Siemens Energy & Automation Base Drive Panel Description General Information Card Rack Assembly Rated DC Current Base Drive Panel Catalog Numbers Horsepower Amps DC Catalog No 240V DC 500V DCUS Rating Quad Type Technical Assistance ServiceSpare Parts 800-333-PIC1 Options Order No Option Part NumbersEB1, EB2, SBP and SLB boards Printed Circuit Boards Description Where Used Part RecomSpare Parts Cables Description Where Used Part Number Recom Fans/Blowers Field Converter Thyristor Modules Armature Converter Thyristor Modules, for 4-Quad DrivesField Converter Diode Modules Power Fuses Armature Converter AC Line Fuses, 1PFU 3 PFU Armature Converter DC Fuses, 4-Quad Only, 4PFU Control Transformer Secondary Fuse 3CFU Field Converter AC Line Fuses 1 & 2FSFUControl Transformer Primary Fuses 1CFU, 2CFU Description Contactor Coil Suppressor 1SP, Ensp Control Transformer 1CTR, 2CTR, 3CTRMain Contactor M Auxiliary Relay, EN, and Rectifier Bridge, Mrec Standard Terms and Conditions of Sale Siemens Energy & Automation, Inc. Seller Operating Instructions Siemens Energy & Automation Procedure for Shipping Damage Receiving, unpacking Siemens Energy & Automation 15ADC to 100ADC Base Drive Panels, 3AC 460V, 1 & 4Q 100 140ADC to 850ADC Base Drive Panels, 3AC 460V, 1 & 4Q 140 210 255 430 510 850 1180 1660 1680 Ambient temperature Reduction in base drive dc ampere rating Applicable standards Siemens Energy & Automation Installation and Dimensions Installation Information Base Drive Panel Outlines Dimensions are mm inches15 30 AMP Base Drive PANELS, 1 & 4Q AMP Base Drive PANEL, 1 & 4Q Terminals 80 Power Terminals L1 L2 L3 A1 A2 1120 44.1 1100 43.3 AMP Base Drive PANEL, 1 & 4Q AMP Base Drive PANEL, 1 & 4Q 280 11.0 1200 47.2 740 29.1 965 38.0 AMP Base Drive PANEL, 1 & 4Q 965 38.0 Siemens Energy & Automation Base Drive Panel Connections Base Drive Panel Schematics Base Drive PANEL, 15 AMPS, 1 & 4 Quad Base Drive PANEL, 30 AMPS, 1 & 4 Quad Base Drive PANEL, 60 AMPS, 1 & 4 Quad Base Drive PANEL, 100 AMPS, 1 & 4 Quad Base Drive PANEL, 140 AMPS, 1 & 4 Quad INCH- LBS Base Drive PANEL, 210 AMPS, 1 & 4 Quad Base Drive PANEL, 255 AMPS, 1 & 4 Quad Base Drive PANEL, 430 AMPS, 1 & 4 Quad 1CTR Base Drive PANEL, 510 AMPS, 1 & 4 Quad Base Drive PANEL, 850 AMPS, 1 & 4 Quad Base Drive PANEL, 1180 AMPS, 1 & 4 Quad 3CTR Base Drive PANEL, 1660 AMPS, 1 & 4 Quad 2CTR 3CTR Base Drive PANEL, 1680 AMPS, 1 & 4 Quad Catalog no RA7096-4GV62-0Z+X01, 4-QUAD Operating Instructions Control Connections CUD1 CUD Terminal Locations CUD1 Control Connections CUD2 Optional CUD2 Control Connections Terminal Locations CUD2 Description of Power/Control Terminals Base Drive Panel Power Connections 15 to 100 Amp Base Drive Panel Power Connections 430 to 1680 Amp Motor Armature circuit Function Terminal Connection values/Remarks Possible Internally connected to incoming 460 VAC, 3 Phase Siemens Energy & Automation General safety information for start-up Start-Up Operator control panels Simple operator control panel PMU Parameterization Unit User-friendly operator control panel OP1S LED displays Parameter types Parameterization procedureParameterization on simple operator control panel Operating Instructions PMU Typical Connection DiagramsA1+ A2- 80+ Speed Reset to factory default values and adjust offsets Execution of the default function Start-up procedure Panels Adjustment to actual converter supply voltage Access authorizationAdjustment of converter rated currents Input of motor data Pulse encoder type Normal selection Freely wired actual valueOperation with pulse encoder Operation without tachometer EMF control Field data Selection of basic technological functions Execution of optimization runs Siemens Energy & Automation Operating Instructions Source of Start Command P654 = Checking and possible fine adjustment of maximum speedSetting Application Functions Starting the Drive Speed Setpoint Selection Source of Speed Setpoint P433 = Source of Jog Command P435 = Value Jog Inching ConfigurationSource of Jog Setpoint P436 = Value Documentation of setting values Siemens Energy & Automation General information about faults Fault messagesOn the OP1S 2.1 Supply faults List of fault messagesFurther information about the causes of fault messages F001 Failure of electronics power supply Fault Description P078.001 ∗ 100%P353 F006 Undervoltage F007 Overvoltage F011 Telegram failure at GSST1 Interface errorParameter P363 USS telegram failure at G-SST1 Peer-to-peer telegram failure at G-SST2 F012 Telegram failure at GSST2USS telegram failure at G-SST2 F013 Telegram failure at GSST3 F017 Hardware fault on expansion board EB2 External faultsF016 Hardware fault on expansion board EB1 F015 Telegram failure on one Simolink board F022 External fault Fault messages from motor sensorsF021 External fault F023 Fault message from free function block FB2 P493=2 or 3 temperature sensor at terminals 22 / 23 or Drive faultsF029 Motor overtemperature active in all operating states P494=2 or 3 temperature sensor at terminals 204 F035 Drive is blocked F034 Fault message from free function block FB5F038 Overspeed Cause as a function of fault value F042 Tachometer fault Fault Description Start-up faults F050 Fault Description Fault Description Fault Description Fault Description F051 No optimization run when permanent memory is disabled V2.1 and later F058 Parameter settings are not consistent F056 Important parameter is not set Operating Instructions Hardware faults Number of faulty parameter Internal faultsR047 Index 002 to F067 Converter cooling faulty FaultF064 Watchdog timer has initiated a reset F063 Communication errors with supplementary boards F069 Mlfb data are faulty active in all operating states F082 CB/TB message timeout or error in data exchange F080 Error in initialization of a CB/TB boardF081 CB/TB heartbeat error F078 Fault messages from supplementary boards F101 to F147 Alarm messages A029 Motor overtemperature active in all operating states Alarm Description A025 Brush length too shortA028 Motor overtemperature active in all operating states A026 Poor bearing condition active in all operating states A047 Analog select input 1 terminals 6 and 7 faulty A034 Alarm message from free function block FB9A039 I2t value of power section too high A035 Drive blocked A054 Alarm message from free function block FB259 Alarm Description A049 SCB1 No SCI slave connectedA053 Alarm message from free function block FB258 A067 Converter cooling faulty Siemens Energy & Automation 10-1 OverviewSimoreg DC Master Base Drive Panel Operating Instructions P899 Parameters for DriveMonitor and OP1S 10-2Range of parameter numbers Function R999 10-3 Overview of abbreviationsS00 10-4 Operating status display 10-5 10-6 General visualization parameters 10-7 10-8 10-9 10-10 Access authorization levels 10-11 10-12 Definition of Simoreg DC Master converter 10-13 P067 Load class 10-14R065 Software identifiers R068 Options according to rating plate 10-15 Temp = k1 10-16P077 Total thermal reduction factor P078 Reduction of converter rated supply voltage P080 Control word for brake control Setting values for converter control10-17 P081 EMF-dependent field weakening 10-18 Internal field power moduleExternal field power module 40.00A field No field P086 Voltage failure period for automatic restart P085 Wait period after cancellation of inching command10-19 P087 Brake release time P090 Stabilization time for line voltage 10-20P091 Setpoint threshold 10-21 P093 Pick-up delay for line contactorP094 Switch-off delay for auxiliaries P095 Pick-up time for a contactor in the DC circuit Definition of motor 10-22 10-23 Magnetization characteristic field characteristic 10-24 10-25 Example of a field characteristic 10-26 10-27 Single/multiple evaluation of encoder pulses P142 Matching to pulse encoder signal voltage10-28 P140 Selection of pulse encoder type 10-29 P144 Multiple evaluation of encoder signalsRev/min FS=500.0 P051 G145 1rev/min Type O4 Online 100% 10-30 10-31 Current limitation, torque limitation 10-32 10-33 Speed controller Auto-reversing stage, armature gating unit10-34 10-35 Closed-loop field current control, field gating unit 10-36 10-37 Closed-loop EMF control 10-38 10-39 P295 Mode for rounding the ramp-function generatorRamp-function generator P296 Ramp-down time of ramp generator with quick stop OFF3 10-40 Setpoint processing 10-41 Setting values for monitoring functions and limits 10-42 Setting values for limit-value monitors 10-43 10-44 Settable fixed values 10-45 Fixed control bits 10-46 10-47 Position sensing with pulse encoder 10-48 Motorized potentiometer Connector selector switches10-49 10-50 Definition of Motor interface Oscillation10-51 P497 Air flow Tripping of alarm or fault message Tripping of alarm or fault messageP496 Bearing condition Tripping of alarm or fault message P498 Temperature switch Tripping of alarm or fault message Speed limiting controller Configuring of torque shell input10-53 Friction compensation 10-54 Compensation of moment of inertia dv/dt injection 10-55 P550 Gain in the adaptation range 10-56Speed controller adaptation P551 Integration time in the adaptation range 10-57 Field reversal Input quantities for signals10-58 Configuring of closed-loop control 10-59 P602 Source for armature current controller actual value 10-60Speed limiting controller . Both values are added Actual value P606 Source for variable negative torque limit 10-61P605 Source for variable positive torque limit P607 Source for torque setpoint for master drive 10-62 10-63 10-64 10-65 10-66 Control word, status word 10-67 10-68 10-69 P690 Source for control word 2, bit30 Further configuring measures10-70 P691 Source for control word 2, Bit31 10-71 10-72 P707 Resolution of Main setpoint analog inputP713 Mode of signal injection at Analog selectable input P711 Normalization of Analog selectable input 10-73 10-74 Analog outputs 10-75 10-76 Binary outputs 10-77 Configuration of serial interfaces on basic converter 10-78 10-79 See Change Access / Status P786 USS bus address for G-SST1R789 Diagnostic information for G-SST1 P787 Telegram failure time for G-SST1 P793 Baud rate for G-SST2 10-80P792 Length of parameter jobs for G-SST2 Ind None P052 = Baud FS=6 P051 = G171 Type O2 Offline G173 P796 USS bus address for G-SST2 See Change Access / Status P795 Options for G-SST210-81 P797 Telegram failure time for G-SST2 P801 Number of process data for G-SST3 10-82Violation of telegram residual transfer time USS prot. only P802 Length of parameter jobs for G-SST3 P804 Source for transmit data for G-SST3 See Change Access / Status P803 Baud rate for G-SST310-83 P805 Options for G-SST3 10-84 R809 Diagnostic information for G-SST3P808 R811 Transmit data on G-SST1 See Change Access / Status R810 Receive data on G-SST110-85 R812 Receive data on G-SST2 10-86 R815 Transmit data on G-SST3 Compensation values Deactivation of monitoring functions10-87 Profile parameters Thyristor diagnosisParameters for DriveMonitor and OP1S 10-88 R949 Fault value Fault memoryR947 Fault memory R951 Fault text P952 Number of faults Visualization parameters Alarms 10-90 Visualization parameters Control and status word Device identification10-91 R982 List of existing parameter numbers, continuation R980 List of existing parameter numbers, startR981 List of existing parameter numbers, continuation R983 List of existing parameter numbers, continuation 10-93 10-94 Simplified block diagrams Basic functions Sheet 1 Legend Siemens Energy Sheet 2 Speed Setpoint System Sheet 3 Speed Controller and Current Limit Sheet 4 Armature Current Control 11-6 Sheet 5 EMF and Field Current Control USS interface Sheet 6 USSInterface 1 Interface 2 Sheet 7 USSX172 Sheet 8 Peer to Peer Interface Peer-to-peer interface Sheet 9 Data Exchange CB / TB to Base PZD Word SheetControl word 11-12 Sheet 11 Control Status Word Status word 11-14 Meaning Signals SignalsSheet 11-16 Sheet 15 Miscellaneous Siemens Energy & Automation, Inc