Siemens 6RA70 specifications 10-74

	PNU		Description				Value range	No. indices	See
							[Unit]	Factory	Change
							Steps	setting	(Access /
								Type	Status)
	Analog input terminals 10 / 11 (analog selectable input 3)
						-1000.0 to 1000.0
	P731		Normalization of "Analog selectable input 3"					Ind: 4	P052	= 3
			This parameter specifies the percentage value which is generated for an			[%]		FS=100.0	P051	= 40
	FDS					0.1%		Type: I2	Online
			input voltage of 10V (or an input current of 20mA) at the analog input.
	(G114)		The following generally applies:
			For voltage input:
			P731 [%] =10 V ∗ Y		X .. Input voltage in volts
				X	Y .. % value which is generated for input
			With current input:		voltage X
			P731	[%] = 20 mA ∗ Y	X .. Input current in mA
				X	Y .. % value which is generated for input
					current X
	P732		Offset for "Analog selectable input 3"				-200.00 to 199.99	Ind: None	P052	= 3
						[%]		FS=0.00	P051	= 40
	(G114)					0.01%		Type: I2	Online
	P733		Mode of signal injection at "Analog selectable input 3"				0 to 3	Ind: None	P052	= 3
*		0 =		Injection of signal with sign		1		FS=0	P051	= 40
								Type: O2	Offline
	(G114)	1 =		Injection of absolute value of signal
		2 =		Injection of signal with sign, inverted
		3 =		Injection of absolute value of signal, inverted
	P734		Source for selection of sign reversal at "Analog selectable input 3"				All binector numbers	Ind: None	P052	= 3
*			Selection of binector to control sign reversal at the analog input ("1" state			1		FS=0	P051	= 40
								Type: L2	Offline
	(G114)		= reverse sign)
			0 = binector B0000
			1 = binector B0001
			etc.
	P735		Filtering time for "Analog selectable input 3"				0 to 10000	Ind: None	P052	= 3
			Note: Hardware filtering of approximately 1 ms is applied as standard.				[ms]	FS=0	P051	= 40
	(G114)						1ms	Type: O2	Online
	P736		Source for enabling of "Analog selectable input 3"				All binector numbers	Ind: None	P052	= 3
*			Selection of binector to control enabling of the analog input ("1" state =			1		FS=1	P051	= 40
								Type: L2	Offline
	(G114)		enabled)
			0 = binector B0000
			1 = binector B0001
			etc.

Analog input terminals 103 / 104 (main actual value)

P741	Normalization for "Main actual value”		-270.00 to 270.00	Ind: 4	P052	= 3
FDS	Rated value of input voltage at nmax (=tachometer voltage at maximum		[V]	FS=60.00	P051	= 40
			0.01V	Type: I2	Online
	speed)
(G113)	This parameter defines the maximum speed when P083=1.
P742	Offset for "Main actual value" analog input		-200.00 to 199.99	Ind: None	P052	= 3
			[%]	FS=0.00	P051	= 40
(G113)			0.01%	Type: I2	Online
P743	Mode of signal injection at "Main actual value" analog input		0 to 3	Ind: None	P052	= 3
*	0 =	Injection of signal with sign	1	FS=0	P051	= 40
				Type: O2	Offline
(G113)	1 =	Injection of absolute value of signal
	2 =	Injection of signal with sign, inverted
	3 =	Injection of absolute value of signal, inverted
P744	Source for selection of sign reversal at "Main actual value" analog		All binector numbers	Ind: None	P052	= 3
*	input		1	FS=0	P051	= 40
(G113)	Selection of binector to control sign reversal at the analog input ("1" state			Type: L2	Offline
	= reverse sign)
	0 = binector B0000
	1 = binector B0001
	etc.
P745	Filtering time for "Main actual value" analog input		0 to 10000	Ind: None	P052	= 3
	Note: Hardware filtering of approximately 1 ms is applied as standard.		[ms]	FS=0	P051	= 40
(G113)			1ms	Type: O2	Online
10-74			SIEMENS Energy & Automation
		SIMOREG DC Master Base Drive Panel Operating Instructions