Siemens 6RA70 specifications 10-52, Tripping of alarm or fault message

	PNU		Description			Value range			No. indices		See
						[Unit]			Factory		Change
						Steps			setting		(Access /
									Type		Status)
	P492		Analog monitoring of motor temperature: Trip temperature			0 to 200			Ind: 4		P052 = 3
	FDS		Operative only when P490.x=1.			[°C]			FS=0		P051 = 40
	(G185)					1°C			Type: O2		Online
	P493		Motor temperature analog 1 (temperature sensor at terminals 22 / 23):		0 to 3			Ind: 4		P052 = 3
*			Tripping of alarm or fault message		1			FS=0		P051 = 40
	FDS		Motor temperature grasped with KTY84					Type: O2		Offline
	(G185)	0		Monitoring deactivated
		1		Alarm (A029) at temperature > P491
		2		Fault message (F029) at temperature > P492
		3		Alarm (A029) at temperature > P491 and
				fault message (F029) at temperature > P492
		Motor temperature grasped with PTC thermistor
		0		Monitoring deactivated
		1		Alarm message (A029) when operating point of PTC thermistor
				is reached
		2		Fault message (F029) when operating point of PTC thermistor is
				reached
		3		Illegal setting
	P494		Motor temperature analog 2 (temperature sensor at terminals 204 /		0 to 3			Ind: 4		P052 = 3
*			205): Tripping of alarm or fault message		1			FS=0		P051 = 40
	FDS		Motor temperature grasped with KTY84					Type: O2		Offline
	(G185)	0		Monitoring deactivated
		1		Alarm (A029) at temperature > P491
		2		Fault message (F029) at temperature > P492
		3		Alarm (A029) at temperature > P491 and
				fault message (F029) at temperature > P492
		Motor temperature grasped with PTC thermistor
		0		Monitoring deactivated
		1		Alarm message (A029) when operating point of PTC thermistor
				is reached
		2		Fault message (F029) when operating point of PTC thermistor is
				reached
		3		Illegal setting
	P495		Brush length sensing: Tripping of alarm or fault message			0 to 2		Ind: 4		P052 = 3
*		0		No brush length sensing (terminal 211 is not scanned)	1			FS=0		P051 = 40
	FDS							Type: O2		Offline
		1		Binary brush length sensing (terminal 211 is scanned)
	(G186)			Alarm (A025) in response to 0 signal
		2		Binary brush length sensing (terminal 211 is scanned)
				Fault message (F025) in response to 0 signal
	P496		Bearing condition: Tripping of alarm or fault message			0 to 2		Ind: 4		P052 = 3
*		0		No bearing condition sensing (terminal 212 is not scanned)	1			FS=0		P051 = 40
	FDS							Type: O2		Offline
		1		Bearing condition sensing (terminal 212 is scanned)
	(G186)			Alarm (A026) in response to 1 signal
		2		Bearing condition sensing (terminal 212 is scanned)
				Fault message (F026) in response to 1 signal
	P497		Air flow: Tripping of alarm or fault message			0 to 2		Ind: 4		P052 = 3
*		0		No air flow monitoring (terminal 213 is not scanned)	1			FS=0		P051 = 40
	FDS							Type: O2		Offline
		1		Air flow monitoring (terminal 213 is scanned)
	(G186)			Alarm (A027) in response to 0 signal
		2		Air flow monitoring (terminal 213 is scanned)
				Fault message (F027) in response to 0 signal
	P498		Temperature switch: Tripping of alarm or fault message			0 to 2		Ind: 4		P052 = 3
*		0		No temperature switch connected (terminal 214 is not scanned)	1			FS=0		P051 = 40
	FDS							Type: O2		Offline
		1		Temperature switch connected (terminal 214 is scanned)
	(G186)			Alarm (A028) in response to 0 signal
		2		Temperature switch connected (terminal 214 is scanned)
				Fault message (F028) in response to 0 signal
10-52							SIEMENS Energy & Automation
				SIMOREG DC Master Base Drive Panel Operating Instructions