Siemens 6RA70 specifications 10-12

	PNU		Description			Value range			No. indices		See
						[Unit]			Factory		Change
						Steps			setting		(Access /
									Type		Status)
	P053		Control word for the permanent memory		[SW 1.7 and later]	0 to 1			Ind: 2		P052 = 3
*			Disabling or enabling write accesses to the permanent memory			1			FS=1		P051 = 0
									Type: O2		on-line
			i001:	Disabling or enabling write accesses to the parameter memory
				0 Only save parameter P053 in the permanent memory;
				parameter changes are active immediately but the changed
				values are only stored temporarily and are lost when the
				electronics supply voltage is switched off
				1 Save all parameter values in the permanent memory
			i002:	Disabling or enabling write accesses to the memory of the
				nonvolatile process data
				0 Do not save nonvolatile process data in the permanent
				memory
				1 Save all nonvolatile process data in the permanent memory
				If the nonvolatile process data are not stored (P053.002=0),
				data are lost when the electronics supply of the SIMOREG DC
				Master is switched off, i.e. they have the value 0 after the
				electronics supply is switched on again:
				K0240: Setpoint of the motor potentiometer
				K0309: Motor heating
				K0310: Thyristor heating
				K9195: Output of the 1st tracking/storage element
				K9196: Output of the 2nd tracking/storage element
	P054		OP1S – Background lighting			0, 1			Ind: None	P052 = 3
		0		ON continuously				FS=0		P051 ≥ 0
								Type: O2		Online
		1		ON when panel is in use
	P055		Copy function data set			011 to 143		Ind: None		P052 = 3
*			This parameter allows parameter set 1, 2, 3 or 4 to be copied to parameter			1		FS=012		P051 = 40
								Type: L2		Offline
	(G175)		set 1, 2, 3 or 4. This function is applicable only to parameters with 4 indices
			in the function data set (see also Section 9.1, Data sets and Section 9.11,
			and Section 8, Sheet G175).
			0xy	Do nothing, automatic resetting value at the end of a copy
				operation.
			1xy	The contents of parameter set x (source data set, x=1, 2, 3 or 4)
				are copied to parameter set y (target data set, y=1, 2, 3 or 4)
				(parameter set x remains unchanged, the original contents of
				parameter set y are overwritten).
				x and y are the respective parameter set numbers (1, 2, 3 or 4)
				of the source and target parameter sets.
			The copy operation is started by switching P055 over into parameter mode
			when P055=1xy.
			During the copy operation, the numbers of the parameters being copied are
			displayed on the operator panel (PMU).
			At the end of the copy operation, P055 is reset to P055=0xy.
	r056		Display of active function data set			1 to 4		Ind: None		P052 = 3
	(G175)					1		Type: O2
	P057		Copy Bico data set			011 to 121		Ind: None		P052 = 3
*			This parameter allows parameter set 1 or 2 to be copied to parameter set 1			1		FS=012		P051 = 40
								Type: L2		Offline
			or 2. This function is applicable only to parameters with 2 indices in the Bico
	(G175)		data set (see also Section 9.1, Data sets and Section 9.11, and Section 8,
			Sheet G175).
			0xy	Do nothing, automatic resetting value at the end of a copy
				operation.
			1xy	The contents of parameter set x (source data set, x=1 or 2) are
				copied to parameter set y (target data set, y=1 or 2) (parameter
				set x remains unchanged, the original contents of parameter set
				y are overwritten).
				x and y are the respective parameter set numbers (1 or 2) of the
				source and target parameter sets.
			The copy operation is started by switching P057 over into parameter mode
			when P057=1xy.
			During the copy operation, the numbers of the parameters being copied are
			displayed on the operator panel (PMU).
			At the end of the copy operation, P057 is reset to P057=0xy.
	r058		Display of active Bico data set			1 to 2		Ind: None		P052 = 3
	(G175)					1		Type: O2
10-12							SIEMENS Energy & Automation
					SIMOREG DC Master Base Drive Panel Operating Instructions