Siemens 6RA70 specifications 10-65

PNU

Description

Value range [Unit] Steps

No. indices Factory setting Type

See Change (Access / Status)

P634	Source for limitation input at ramp-function generator output
*	Selection of connectors which must be added up to provide the limitation
(G137)	input at the ramp-function generator output (setpoint limitation).
	0 = connector K0000
	1 = connector K0001
	etc.
P635	Source for ramp-function generator setpoint
*	Selection of connector to be injected as the ramp-function generator
FDS
	setpoint
(G135)	0 = connector K0000
	1 = connector K0001
	etc.
P636	Source for reduction signal for ramp-function generator times
*	Selection of connector to be injected as the reduction signal for the ramp-
(G136)	function generator times
	i001 acts on ramp-up and ramp-down time (P303, P304)
	i002 acts on lower and upper transition roundings (P305, P306)
	i003 acts on ramp-up time (P303)
	i004 acts on ramp-down time (P304)
	i005 acts on lower transition rounding (P305)
	i006 acts on upper transition rounding (P306)
	0 = connector K0000
	1 = connector K0001
	etc.

All connector numbers

1

All connector numbers

1

All connector numbers

1

Ind: 2	P052	= 3
FS=	P051	= 40
i001: 190	Offline
i002: 0
Type: L2
Ind: 4	P052	= 3
FS=194	P051	= 40
Type: L2	Offline

Ind: 6	P052	= 3
FS=1	P051	= 40
Type: L2	Offline

P637	Source for selection of "Ramp-function generator setting 2"
*	Selection of binector to control switchover to "Ramp-function generator
BDS
	setting 2".
(G136)	With a log. "1" signal at the binector, ramp-function generator parameter set
	2 (P307 - P310) is selected. This function has a higher priority than the
	ramp-up integrator function.
	0 = binector B0000
	1 = binector B0001
	etc.
P638	Source for selection of "Ramp-function generator setting 3”
*	Selection of binector to control switchover to "Ramp-function generator
BDS
	setting 3".
(G136)	With a log. "1" signal at the binector, ramp-function generator parameter set
	3 (P311 - P314) is selected. This function has a higher priority than the
	ramp-up integrator function.
	0 = binector B0000
	1 = binector B0001
	etc.
P639	Source for the ramp-function generator setting values
*	Selection of the connectors that are connected as the ramp-function
(G136)	generator setting values.
	i001 Setting value for the ramp-function generator output in state log.
	"1" of the binector selected via P640
	i002 Setting value for the ramp-function generator output if the drive
	is not in state "Operating" (B0104=0) and the binector selected
	via P640 is in state log. "0"
	[i002 only available with SW 1.6 and later]
	0 = Connector K0000
	1 = Connector K0001
	etc.
P640	Source for selection of "Set ramp-function generator”
*	Selection of binector to control the "Set ramp-function generator" function
BDS
	0 = binector B0000
(G136)	1 = binector B0001
	etc.

All binector numbers	Ind: 2	P052	= 3
1	FS=0	P051	= 40
	Type: L2	Offline

All binector numbers	Ind: 2	P052	= 3
1	FS=0	P051	= 40
	Type: L2	Offline

All connector	Ind: 2	P052	= 3
numbers	FS=167	P051	= 40
1	Type: L2	≥off-line

All binector numbers	Ind: 2	P052	= 3
1	FS=0	P051	= 40
	Type: L2	Offline

SIEMENS Energy & Automation	10-65
SIMOREG DC Master Base Drive Panel Operating Instructions