Siemens 6RA70 Further configuring measures, 10-70, P690 Source for control word 2, bit30

	PNU	Description		Value range		No. indices		See
				[Unit]		Factory		Change
				Steps		setting		(Access /
						Type		Status)
	P689	Source for control word 2, bit29		All binector numbers	Ind: 2		P052 = 3
*		(0=external alarm 2, 1=no external alarm 2)		1	FS=1		P051 = 40
	BDS				Type: L2		Offline
	(G181)
	P690	Source for control word 2, bit30		All binector numbers	Ind: None		P052 = 3
*		(0=select Bico data set 1, 1=select Bico data set 2)		1	FS=0		P051 = 40
	(G181)				Type: L2		Offline
	P691	Source for control word 2, Bit31	[SW 1.8 and later]	All binector numbers		Ind: 2		P052 = 3
*		Main contactor checkback signal:		1		FS=0		P051 = 40
	BDS					Type: L2		Offline
		(0 = main contactor dropped out, 1 = main contactor picked up)
	(G181)	This control input is intended as a means of looping an auxiliary contact of
		the main contactor into the device control.
		During the Power ON routine, this signal must switch to "1" within the time
		period set in P095. If it does not, or it disappears during operation, fault
		message F004 with fault value 6 is activated.
		P691 = 0: Bit 31 of control word 2 is inoperative.
		(This setting of P691 is always active, regardless of whether
		control word 2 is input in word mode [P649 = 9] or bit mode
		[P649 <> 9])
		P691 = 1: Bit 31 of control word 2 is inoperative.
		(This setting of P691 is active only when control word 2 is input
		in bit mode, i.e. when P649 <> 9)

10.36 Further configuring measures

P692	Source for selection of injection of standstill field		All binector numbers	Ind: 2	P052	= 3
*	Selection of binector to control injection of the standstill field ("0" state =		1	FS=0	P051	= 40
BDS				Type: L2	Offline
	inject standstill field)
(G166)	Note:	The delay time set in P258 is not effective when this function is
		active.
	0 = binector B0000
	1 = binector B0001
	etc.
P693	Source for selection of enabling command for EMF controller		All binector numbers	Ind: 2	P052	= 3
*	Selection of binector which is to control enabling of the EMF controller		1	FS=1	P051	= 40
BDS				Type: L2	Offline
	0 = binector B0000
(G165)
	1 = binector B0001
	etc.
P694	Source for selection of enabling command for "Torque limit		All binector numbers	Ind: 2	P052	= 3
*	switchover”		1	FS=0	P051	= 40
BDS	Selection of binector which is to control enabling of the "Torque limit			Type: L2	Offline
(G160)	switchover" function (1=enable, see also Sheet G160 in Section 8 of
	Operating Instructions 6RX1700-0AD** and P180 to P183)
	0 = binector B0000
	1 = binector B0001
	etc.
P695	Source for selection of "Set speed controller I component" function		All binector numbers	Ind: 2	P052	= 3
*	Selection of binector to control the "Set I component" function		1	FS=0	P051	= 40
BDS				Type: L2	Offline
	0 = binector B0000
(G152)	1 = binector B0001
	etc.

When the binector selected in P695 switches from log. "0" to log. "1", the I component of the speed controller is set to the value of the connector selected in P631.

With this function it is possible, for example, to use the same signal (binector) to control controller enabling commands and setting of the I component.

10-70	SIEMENS Energy & Automation
	SIMOREG DC Master Base Drive Panel Operating Instructions