Siemens 6RA70 specifications 10-71

PNU

Description

Value range [Unit] Steps

No. indices Factory setting Type

See Change (Access / Status)

P696	Source for selection of "Stop speed controller I component" function
*	Selection of binector to control the "Stop I component" function
BDS
	0 = binector B0000
(G152)	1 = binector B0001
	etc.
	When the binector selected in P696 changes to the log. "1" state, the I
	component of the speed controller is stopped.
P697	Source for selection of enabling of dv/dt injection
*	Selection of binector to control enabling of dv/dt injection (state "1" =
BDS
	enable)
(G153)	0 = binector B0000
	1 = binector B0001
	etc.
P698	Source for selection of enabling command for speed-dependent speed

*controller PI / P function switchover

BDS	Selection of binector to control enabling of the speed-dependent PI / P
(G152)	controller switchover function (see also P222)
	0 = binector B0000
	1 = binector B0001
	etc.

All binector numbers	Ind: 2	P052	= 3
1	FS=0	P051	= 40
	Type: L2	Offline

All binector numbers	Ind: 2	P052	= 3
1	FS=1	P051	= 40
	Type: L2	Offline

All binector numbers	Ind: 2	P052	= 3
1	FS=1	P051	= 40
	Type: L2	Offline

10.37 Analog inputs (main actual value, main setpoint, selectable inputs)

(see also Section 8, Sheets G113 and G114 of Operating Instructions 6RX1700-0AD**)

Analog input terminals 4 / 5 (main setpoint)

P700	Signal type of "Main setpoint" analog input
*	0 =	Voltage input 0 to ±10 V
(G113)	1 =	Current input 0 to ±20 mA
	2 =	Current input 4 to 20 mA
P701	Normalization of "Main setpoint" analog input
FDS	This parameter specifies the percentage value which is generated for an
	input voltage of 10V (or an input current of 20mA) at the analog input.
(G113)	The following generally applies:
	For voltage input:
	P701 [%] =10 V ∗ Y		X .. Input voltage in volts
		X	Y .. % value which is generated for input
	With current input:		voltage X
	P701 [%] = 20 mA ∗ Y		X .. Input current in mA
		X	Y .. % value which is generated for input
			current X
P702	Offset for "Main setpoint" analog input
(G113)
P703	Mode of signal injection at "Main setpoint" analog input
*	0 =	Injection of signal with sign
(G113)	1 =	Injection of absolute value of signal
	2 =	Injection of signal with sign, inverted
	3 =	Injection of absolute value of signal, inverted
P704	Source for selection of sign reversal at "Main setpoint" analog input
*	Selection of binector to control sign reversal at the analog input ("1" state
(G113)	= reverse sign)
	0 = binector B0000
	1 = binector B0001
	etc.
P705	Filtering time for "Main setpoint" analog input
(G113)	Note: Hardware filtering of approximately 1 ms is applied as standard.

0 to 2

1

-1000.0 to 1000.0 [%] 0.1%

-200.00 to 199.99 [%] 0.01%

0 to 3

1

All binector numbers 1

0 to 10000 [ms] 1ms

Ind: None	P052	= 3
FS=0	P051	= 40
Type: O2	Offline
Ind: 4	P052	= 3
FS=100.0	P051	= 40
Type: I2	Online

Ind: None	P052	= 3
FS=0.00	P051	= 40
Type: I2	Online
Ind: None	P052	= 3
FS=0	P051	= 40
Type: O2	Offline
Ind: None	P052	= 3
FS=0	P051	= 40
Type: L2	Offline

Ind: None	P052	= 3
FS=0	P051	= 40
Type: O2	Online

SIEMENS Energy & Automation	10-71
SIMOREG DC Master Base Drive Panel Operating Instructions