Siemens 6RA70 specifications 10-82, Violation of telegram residual transfer time USS prot. only

PNU	Description		Value range	No. indices	See
			[Unit]	Factory	Change
			Steps	setting	(Access /
				Type	Status)
r799	Diagnostic information for G-SST2			Ind: 10	P052 = 3
	Free-running counter, overflow at 65535			Type: O2
(G171)
		Number of error-free telegrams
(G173)	i001:
	i002:	Number of errored telegrams:
		Byte frame, parity, overrun or BCC error
	i003:	Number of byte frame errors
	i004:	Number of overrun errors
	i005:	Parity error
	i006:	STX error:
		Start interval before STX not observed,
		telegram residual transfer time not observed,
		delay time of LGE character too long,
		erroneous STX, i.e. ≠ 02
	i007:	Violation of telegram residual transfer time (USS prot. only)
	i008:	Block check error
	i009:	Incorrect telegram length:
		With P792=3 or 4 only:
		The length of the received telegram is ≠ P791 + P792
		(Note: If the received values are correct, they will be processed
		even when this error has been detected)
	i010:	Timeout error:
		No valid telegram has been received for a period exceeding the
		setting in P797. After the occurrence of a timeout error, this
		counter is not activated again until the next valid telegram is
		received.

G-SST 3 (RS485 on X162) (see also Section 8, Sheets G172 and G174 and Section 9 of Operating Instructions 6RX1700-0AD**)

P800	Selection of protocol for G-SST3 basic converter interface		0, 2, 5, 9	Ind: None	P052 = 3
*	0	Setting has no function	1	FS=0	P051 = 40
(G172)				Type: O2	Offline
	2	USS protocol
(G174)
	5	”Peer-to-peer” communication
	9	For internal factory test purposes
P801	Number of process data for G-SST3		0 to 16	Ind: None	P052 = 3
*	When P800 = 0 or 9 is selected: Parameter is irrelevant		1	FS=2	P051 = 40
(G172)				Type: O2	Offline
(G174)	When USS protocol (P800=2) is selected: Number of PZD elements
	0	No process data are expected or sent in the USS protocol
	1...16	Number of process data words in USS protocol (same number
		applies to transmission and receipt)
		The received PZD elements (1 to max. 16) are available at
		connectors (K6001 to K6016) and, in some cases, bit-serially at
		binectors for "internal wiring" purposes.
		The PZD elements to be transmitted (1 to max. 16) are selected
		in parameters P804.01 to P804.16.
	When peer-to-peer (P800= 5) is selected: Number of transferred words
	0	Illegal setting
	1...5	Number of transferred words
	6...16	Illegal setting
P802	Length of parameter jobs for G-SST3		0, 3, 4, 127	Ind: None	P052 = 3
*			1	FS=127	P051 = 40
(G172)	This parameter is effective only when P800=2 (USS protocol).			Type: O2	Offline
	0	No PKW data are expected or sent in the USS protocol.
	3, 4	3 or 4 PKW data words are expected in the USS protocol and 3
		or 4 PKW data words are also sent (for transmission of
		parameter values).
	127	Number of PKWs is determined by the telegram length

10-82	SIEMENS Energy & Automation
	SIMOREG DC Master Base Drive Panel Operating Instructions