Siemens 6RA70 specifications Definition of motor, 10-22

	PNU	Description			Value range	No. indices	See
					[Unit]	Factory	Change
					Steps	setting	(Access /
						Type	Status)
	P097	Response of field current to fault messages		[SW 2.1 and later]	0 to 1	Ind: None	P052	= 3
*		0	Field pulses are blocked when a fault message is activated		1	FS=1	P051	= 40
	(G166)					Type: O2	Online
		1	Field pulses are not blocked when a fault message is activated,
			but the field current setpoint cannot be increased above its
			current setting.
	P098	Contactor in DC circuit		[SW 2.1 and later]	0 to 1	Ind: None	P052	= 3
*		0	The DC circuit does not include a contactor		1	FS=0	P051	= 40
						Type: O2	Online

1The DC circuit contains a contactor which is controlled by the “relay for the line contactor" (terminals 109 and 110).

The values for the armature voltage Ua and for EMF (K0286, K0287, K0291, K0292, r037, r038) are set to 0% whenever B0124 = 0 (request main contactor not active). This is because the motor terminals are separated in this case from output terminals 1C and 1D of the SIMOREG DC Master and it is then impossible to measure the armature voltage Ua (or the EMF).

10.6Definition of motor

P100	Rated motor armature current (acc. to motor rating plate)		0.0 to 6553.0	Ind: 4	P052 = 3
*	0.0	Parameter not yet set	[A]	FS=0.0	P051 = 40
FDS			0.1A	Type: O2	Offline
(G165)
P101	Rated motor armature voltage (acc. to motor rating plate)		10 to 2800	Ind: 4	P052 = 3
*	Notes:		[V]	FS=400	P051 = 40
FDS			1V	Type: O2	Offline
	One of the functions of this parameter is to determine the point at which
(G165)	field-weakening operation commences.
	If possible, the rated motor armature voltage + the voltage drop in the motor
	feeder cable (for a current setting acc. to P100) should be set in P101.
P102	Rated motor field current (acc. to motor rating plate)		0.00 to 600.00	Ind: 4	P052 = 3
*	0.00 Parameter not yet set		[A]	FS=0.00	P051 = 40
FDS			0.01A	Type: O2	Online
(G165)
P103	Minimum motor field current		0.00 to 100.00	Ind: 4	P052 = 3
*	Note:		[A]	FS=0.00	P051 = 40
FDS			0.01A	Type: O2	Offline
	P103 must be set to <50% of P102 to execute the optimization run for field
(G165)
	weakening (P051=27).
P104	Speed n1 (acc. to motor rating plate)		1 to 10000	Ind: 4	P052 = 3
*	1st point (speed value) in speed-dependent current limitation.		[rev/min]	FS=5000	P051 = 40
			1rev/min	Type: O2	Offline
FDS
	This parameter is used together with P105, P106, P107 and P108 to define
(G161)	the characteristic of the current limiting value as a function of actual speed.
P105	Armature current I1 (acc. to motor rating plate)		0.1 to 6553.0	Ind: 4	P052 = 3
*	1st point (current value) in speed-dependent current limitation.		[A]	FS=0.1	P051 = 40
			0.1A	Type: O2	Offline
FDS
	This parameter is used together with P104, P106, P107 and P108 to define
(G161)	the characteristic of the current limiting value as a function of actual speed.
P106	Speed n2 (acc. to motor rating plate)		1 to 10000	Ind: 4	P052 = 3
*	2nd point (speed value) in speed-dependent current limitation.		[rev/min]	FS=5000	P051 = 40
			1rev/min	Type: O2	Offline
FDS	This parameter is used together with P104, P105, P107 and P108 to define
(G161)	the characteristic of the current limiting value as a function of actual speed.
P107	Armature current I2 (acc. to motor rating plate)		0.1 to 6553.0	Ind: 4	P052 = 3
*	2nd point (current value) in speed-dependent current limitation.		[A]	FS=0.1	P051 = 40
			0.1A	Type: O2	Offline
FDS
	This parameter is used together with P104, P105, P106 and P108 to define
(G161)	the characteristic of the current limiting value as a function of actual speed.

10-22	SIEMENS Energy & Automation
	SIMOREG DC Master Base Drive Panel Operating Instructions