Siemens 6RA70 specifications Access authorization levels, 10-11

	PNU	Description		Value range	No. indices	See
				[Unit]	Factory	Change
				Steps	setting	(Access /
					Type	Status)
	P046	Binector display:		All binector numbers	Ind: 4	P052 = 3
*		i001:	Selection of binector displayed in r045.01	1	FS=0	P051 = 40
					Type: L2	Online
	(G121)	i002:	Selection of binector displayed in r045.02
		i003:	Selection of binector displayed in r045.03
		i004:	Selection of binector displayed in r045.04

r047	Display of fault diagnostic memory
	Provides more detailed information about the cause of a fault after activation
	of a fault message (see Section 10).
	i001	Word 1 (fault value)
	i002	Word 2
	...
	i016	Word 16 (fault number)
r048	Hours run
(G189)	Display of time (hours) in which drive has been operating in states I, II or - -.
	All times of ≥ approx. 0.1 s are included in the count.
r049	Fault time
	Display of time at which the current fault, and the last 7 acknowledged
(G189)	faults, were activated.
	i001:	Current fault	hours
	i002:	1st acknowledged fault	hours
	i003:	2nd acknowledged fault	hours
	i004:	3rd acknowledged fault	hours
	i005:	4th acknowledged fault	hours
	i006:	5th acknowledged fault	hours
	i007:	6th acknowledged fault	hours
	i008:	7th acknowledged fault	hours
P050	Language
*	Language of plaintext display on optional OP1S operator panel and in
	DriveMonitor PC service routine
	0:	German
	1:	English
	2:	Spanish
	3:	French
	4:	Italian

0 to 65535

1

0 to 65535 [hours]

1 hour

0 to 65535 [hours]

1 hour

0 to 4

1

Ind: 16	P052 = 3
Type: O2

Ind: None	P052 = 3
Type: O2
Ind: 8	P052 = 3
Type: O2

Ind: None	P052 = 3
FS=0	P051 ≥ 0
Type: O2	Online

10.3Access authorization levels

P051	Key parameters
*	0	No access authorization

6Do not set (for use by DriveMonitor)

7Do not set (for use by DriveMonitor)

9Do not set (for use by DriveMonitor)

21Restore factory settings

All parameters are reset to their defaults (factory settings). Parameter P051 is then automatically reset to factory setting "40".

22Execute internal offset compensation (see Section 7.4)

25Optimization run for precontrol and current controller (armature and field) (see Section 7.5)

26Optimization run for speed controller (see Section 7.5)

27Optimization run for field weakening (see Section 7.5)

28Optimization run for compensation of friction and moment of inertia (see Section 7.5)

29Optimization run for the speed controller with an oscillating mechanical system (see Section 7.5)

40Access authorization to parameter values for authorized service personnel

P052	Selection of display parameters
*	0	0 Display only parameters that are not set to original factory
		settings
	1	Display only parameters for simple applications
	3	Display all parameters used

see column on left

0, 1, 3

Ind: None	P052 = 3
FS=40	P051 ≥ 0
Type: O2	Online

Ind: None	P052 = 3
FS=3	P051 ≥ 0
Type: O2	Online

SIEMENS Energy & Automation	10-11
SIMOREG DC Master Base Drive Panel Operating Instructions