Siemens 6RA70 specifications 10-64

	PNU	Description	Value range	No. indices	See
			[Unit]	Factory	Change
			Steps	setting	(Access /
				Type	Status)
	P627	Source for input of D element	All connector	Ind: None	P052	= 3
*		Selection of connector to be injected as the input signal for the D element	numbers	FS=178	P051	= 40
			1	Type: L2	Offline
	(G152)
		0 = connector K0000
		1 = connector K0001
		etc.
	P628	Source for input of band-stop filter 1	All connector	Ind: None	P052	= 3
*		Selection of connector to be injected as the input signal for band-stop filter 1	numbers	FS=179	P051	= 40
	(G152)		1	Type: L2	Offline
		0 = connector K0000
		1 = connector K0001
		etc.
	P629	Source for band-stop filter 2	All connector	Ind: None	P052	= 3
*		Selection of connector to be injected as the input signal for band-stop filter 2	numbers	FS=177	P051	= 40
	(G152)		1	Type: L2	Offline
		0 = connector K0000
		1 = connector K0001
		etc.

Speed controller droop

P630

*

(G151)

Source for influencing quantity for speed droop

Selection of connector to be injected as the influencing quantity

0 = connector K0000

1 = connector K0001 etc.

All connector numbers

1

Ind: None

FS=162

Type: L2

P052 = 3

P051 = 40 Offline

Setting the speed controller I component

Function: When the binector selected in P695 switches state from log. "0" to log. "1", the I component of the speed controller is set to the

	value of the connector selected in P631.
	With this function it is possible, for example, to use the same signal (binector) to control controller enabling commands and
	setting of the I component.	All connector
P631	Source for setting value for speed controller integrator		Ind: None	P052 = 3
*	Selection of connector to be injected as the setting value for the I	numbers	FS=0	P051 = 40
		1	Type: L2	Offline
(G152)	component
	0 = connector K0000
	1 = connector K0001
	etc.

Setting values for configuring the setpoint processing function and ramp-function generator

Limitation at ramp-function generator output (setpoint limitation)

(see also Section 8, Sheet G136 of Operating Instructions 6RX1700-0AD**)

The effective limitations are:

Upper limit:		Minimum value of P300 and the four connectors selected with P632
Lower limit:		Maximum value of P301 and the four connectors selected with P633
Note:	The limiting values for both the positive and negative setpoint limits can have a positive or negative sign. The negative setpoint
	limit, for example, can therefore be parameterized to a positive value and the positive setpoint limit to a negative value.
P632	Source for variable positive limitation at ramp-function generator		All connector		Ind: 4	P052 = 3
*	output		numbers		FS=1	P051 = 40
(G137)	Selection of connectors to be injected at the variable positive limitation at		1		Type: L2	Offline
	the ramp-function generator output (setpoint limitation).
	0 = connector K0000
	1 = connector K0001
	etc.
P633	Source for variable negative limitation at ramp-function generator		All connector		Ind: 4	P052 = 3
*	output		numbers		FS=9	P051 = 40
(G137)	Selection of connectors to be injected at the variable negative limitation at		1		Type: L2	Offline
	the ramp-function generator output (setpoint limitation).
	0	= connector K0000
	...
	8	= connector K0008
	9 = value as set in parameter P632 ∗ (−1)
	10 = connector K0010
	etc.
10-64				SIEMENS Energy & Automation
		SIMOREG DC Master Base Drive Panel Operating Instructions