Siemens 6RA70 specifications 10-73

PNU

Description

Value range [Unit] Steps

No. indices Factory setting Type

See Change (Access / Status)

P714	Source for selection of sign reversal at "Analog selectable input 1"
*	Selection of binector to control sign reversal at the analog input ("1" state
(G113)	= reverse sign)
	0 = binector B0000
	1 = binector B0001
	etc.
P715	Filtering time for "Analog selectable input 1"
(G113)	Note: Hardware filtering of approximately 1 ms is applied as standard.
P716	Source for enabling of "Analog selectable input 1"
*	Selection of binector to control enabling of the analog input ("1" state =
(G113)	enabled)
	0 = binector B0000
	1 = binector B0001
	etc.
P717	Resolution of "Analog selectable input 1"
*	See P707
(G113)

All binector numbers	Ind: None	P052	= 3
1	FS=0	P051	= 40
	Type: L2	Offline

0 to 10000	Ind: None	P052	= 3
[ms]	FS=0	P051	= 40
1ms	Type: O2	Online
All binector numbers	Ind: None	P052	= 3
1	FS=1	P051	= 40
	Type: L2	Offline

10 to 14	Ind: None	P052	= 3
[Bit]	FS=12	P051	= 40
1 bit	Type: O2	Offline

Analog input terminals 8 / 9 (analog selectable input 2)

P721	Normalization of "Analog selectable input 2"
FDS	This parameter specifies the percentage value which is generated for an
	input voltage of 10V (or an input current of 20mA) at the analog input.
(G114)	The following generally applies:
	For voltage input:
	P721 [%] =10 V ∗ Y		X .. Input voltage in volts
		X	Y .. % value which is generated for input
	With current input:		voltage X
	P721 [%] = 20 mA ∗ Y		X .. Input current in mA
		X	Y .. % value which is generated for input
			current X
P722	Offset for "Analog selectable input 2"
(G114)
P723	Mode of signal injection at "Analog selectable input 2"
*	0 =	Injection of signal with sign
(G114)	1 =	Injection of absolute value of signal
	2 =	Injection of signal with sign, inverted
	3 =	Injection of absolute value of signal, inverted
P724	Source for selection of sign reversal at "Analog selectable input 2"
*	Selection of binector to control sign reversal at the analog input ("1" state
(G114)	= reverse sign)
	0 = binector B0000
	1 = binector B0001
	etc.
P725	Filtering time for "Analog selectable input 2"
(G114)	Note: Hardware filtering of approximately 1 ms is applied as standard.
P726	Source for enabling of "Analog selectable input 2"
*	Selection of binector to control enabling of the analog input ("1" state =
(G114)	enabled)
	0 = binector B0000
	1 = binector B0001
	etc.

-1000.0 to 1000.0	Ind: 4	P052	= 3
[%]	FS=100.0	P051	= 40
0.1%	Type: I2	Online

-200.00 to 199.99	Ind: None	P052	= 3
[%]	FS=0.00	P051	= 40
0.01%	Type: I2	Online
0 to 3	Ind: None	P052	= 3
1	FS=0	P051	= 40
	Type: O2	Offline
All binector numbers
	Ind: None	P052	= 3
1	FS=0	P051	= 40
	Type: L2	Offline
0 to 10000
	Ind: None	P052	= 3
[ms]	FS=0	P051	= 40
1ms	Type: O2	Online
All binector numbers	Ind: None	P052	= 3
1	FS=1	P051	= 40
	Type: L2	Offline

SIEMENS Energy & Automation	10-73
SIMOREG DC Master Base Drive Panel Operating Instructions