Toshiba VF-AS1 instruction manual Integrating wattmeter, Trace data communication number

E6581301

■Trace data communication number

Communication	Function	Minimum setting	Setting/readout range	Default setting
No.		/readout unit
E000	Trace data 1~4 pointer	￿/￿	￿~￿￿	￿￿
E100￿	Data 1 of trace data 1	￿/￿	￿~￿￿￿￿	￿￿
￿	Data 2~99 of trace data 1	￿/￿	￿~￿￿￿￿	￿￿
E199￿	Data 100 of trace data 1	￿/￿	￿~￿￿￿￿	￿￿
E200￿	Data 1 of trace data 2	￿/￿	￿~￿￿￿￿	￿￿
￿	Data 2~99 of trace data 2	￿/￿	￿~￿￿￿￿	￿￿
E299￿	Data 100 of trace data 2	￿/￿	￿~￿￿￿￿	￿￿
E300￿	Data 1 of trace data 3	￿/￿	￿~￿￿￿￿	￿￿
￿	Data 2~99 of trace data 3	￿/￿	￿~￿￿￿￿	￿￿
E399￿	Data 100 of trace data 3	￿/￿	￿~￿￿￿￿	￿￿
E400￿	Data 1 of trace data 4	￿/￿	￿~￿￿￿￿	￿￿
￿	Data 2~99 of trace data 4	￿/￿	￿~￿￿￿￿	￿￿
E499￿	Data 100 of trace data 4	￿/￿	￿~￿￿￿￿	￿￿
Ex.) When operation frequency data is acquired through a communication device
Data acquired	(￿￿￿￿) h=8000 ￿ 8000×0.01Hz=80.0Hz

■Relationship between pointer and data

The table below shows the relationship between pointer (E000 set value) and trace data (1 to 4).

Pointer (E000 set value)	￿￿	￿￿	￿￿	~	￿￿￿	￿￿￿
Trace data 1'E100"E199(	E100	E101	E102	~	E198	E199
Trace data 2'E200"E299(	E200	E201	E202	~	E298	E299
Trace data 3'E300"E399(	E300	E301	E302	~	E398	E399
Trace data 4'E400"E499(	E400	E401	E402	~	E498	E499

6	<Example of setting> If E000 is set to ￿:
		(Earliest data)				(Latest data)
	Trace data 1	E102	~	E199,	E100,	E101
	Trace data 2	E202	~	E299,	E200,	E201
	Trace data 3	E302	~	E399,	E300,	E301
	Trace data 4	E402	~	E499,	E400,	E401

Note 1: Use the parameters ￿￿￿￿ through ￿￿￿￿￿to specify the types of trace data (1 to 4).

Note 2: Communication numbers E000 is automatically incremented by the inverter when data is traced continuously.

*In ordinary cases, these parameters do not need to be rewritten.

6.38Integrating wattmeter

￿￿￿￿: Integrating wattmeter retention selection

￿￿￿￿: Integrating wattmeter display unit selection

• Function

At the main power off ,it is selectable whether retention of integral output power values or not.

And also, the display unit is selectable.

The integrating wattmeter display can be cleared by external input signal by assignment of the terminal function. Input terminal function 74, 75 (Integrating wattmeter display clear)

Title	Function		Adjustment range	Default setting
￿￿￿￿	Integrating wattmeter retention selection	￿: Disabled		￿￿
		￿: Enabled
		￿: 1 = 1 kWh		Accoding to
		￿: 1	= 10 kWh
				model
￿￿￿￿	Integrating wattmeter display unit selection	￿: 1	= 100 kWh
				￿ Refer to
		￿: 1	= 1000 kWh
				page K-48.
		￿: 1	= 10000 kWh

F-80