Toshiba VF-AS1 instruction manual Mode

! E6581301

[Note 7]

[Note 7]

[Note 7]

[Note 7]

[Note 8]

[Note 9]

8

(Continued)

Commun			Key		LED
ication	Item displayed							Description
		operated			display
No.
FE10	Past trip 1				￿￿￿⇔￿	Past trip 1 (displayed alternately at 0.5-sec. intervals)
FE11	Past trip 2				￿￿! ⇔￿	Past trip 2 (displayed alternately at 0.5-sec. intervals)
FE12	Past trip 3				￿￿￿⇔￿	Past trip 3 (displayed alternately at 0.5-sec. intervals)
FE13	Past trip 4				￿￿￿￿⇔￿	Past trip 4 (displayed alternately at 0.5-sec. intervals)
						The ON/OFF status of each of the cooling fan, circuit
						board capacitor, main circuit capacitor or part
						replacement alarm of cumulative operation time is
						displayed in bits.
	Part replacement					ON: ￿
FE79					￿￿￿￿￿￿!￿			￿￿￿￿￿￿!￿
	alarm information					OFF: ￿
							Cumulative		Cooling fan
						operation time			Control circuit board
									capacitor
									Main circuit capacitor
FE14	Cumulative operation				￿￿￿#￿	The cumulative operation time is displayed.
	time					(Indication of 0.1 represents 10 hours.)
-	Default display mode		MODE		￿￿￿! ￿	Status monitor mode (The code blinks if a trip occurs.)
		!	!	! !		Reverts to the first trip indication.
		!	!	×2

Note 1: If trouble occurs while the CPU is being initialized after the inverter is turned on or reset, the trip record retaining function does not record it but displays a status monitor item.

Note 2: Contents of status indications of *1, *2, *3, *4, *5, *6, *7, and *8 can be selected from 44 kinds of information. Contents of status indications that are set up at ￿￿￿￿~￿￿￿￿ (status monitor 1 to 8 display mode) are displayed.

Note 3: Items displayed when a trip occurs can be changed by pressing or key.

Note 4: You can switch between % and A (ampere)/V (volt), using the parameter %&￿￿ (current/voltage unit selection).

Note 5: The input voltage displayed is 1/ 2 times as large as the rectified DC input voltage.

Note 6: The number of bars displayed varies depending on the setting of ￿￿￿ (logic output/pulse train output selection). The bar representing the OUT-NO terminal is displayed only when logic output function is assigned to it.

If ￿￿￿ =￿:The bar representing OUT-NO is displayed.

If ￿￿￿ =￿:The bar representing OUT-NO is not displayed.

Note 7: Past rip records are displayed in the following sequence: 1 (latest trip record) ⇔2⇔3⇔4 (oldest trip record). If there is no trip record, ￿￿￿￿ is displayed.

Details on past trip record 1, 2, 3 or 4 can be displayed by pressing the ENT key when past trip 1, 2, 3 or 4 is displayed. ￿ For more details, refer to Section 8.2.2.

Note 8: The time elapsed before an end of part replacement alarm is issued is calculated from the average yearly ambient temperature, operation time and load current entered using ￿￿￿￿, and it is no more than an estimation, and therefore it should be used for reference purposes only.

Note 9: The cumulative operation time increments only when the machine is in operation.

Note 10: At the occurrence of a trip, maximum values are not always recorded and displayed for reasons of detecting time.

H-12