! E6581301 G-4
7
■ Table of setting of contact input terminal function
Parameter setting
Function
Parameter setting
Function
Positive
logic
Negative
logic
Positive
logic
Negative
logic
! !
! !  No function is assigned !
!
Simple positioning (positioning loop)
! !
! !  F: Forward run command !
!
Integrating wattme ter displa y clear
! !
! !  R: Reverse run command !
!
Trace back trigger signal
! !
! !  ST: Standby !
!
Light-load high-speed operation
prohibitive signal
! !
! !  RES: Reset !
!
No function assigned
!
! S1: Preset speed 1 !
!
No function assigned
!
! S2: Preset speed 2 !
!
No function assigned
!
! S3: Preset speed 3 !
!
Binary data write
!
! S4: Preset speed 4 !
!
Motor operated pot mop set (up) *1
!
! Jog run !
!
Motor operated pot mop set (down) *1
!
 Emergency stop !
!
Motor operated pot mop set (clear)
!
 DC braking !
!
No function assigned
!

Acceleration/dec eleration s witching 1 *2
!
!
No function assigned
!

Acceleration/dec eleration s witching 2 *2
!
!
Forward/reverse selection
!
 V/f switching signal 1
*2

 Run/stop command
*3
!
 V/f switching signal 2
*2

 Commercial power/INV switching
!
! Torque limit switching signal 1
*2

 Frequency reference priority switching
!
! Torque limit switching signal 2
*2

 VI/II terminal priority
!
 PID control OFF selection 
 Command terminal board priority
!
 Pattern operation group 1 
 Permission of parameter editing
!
 Pattern operation selection 2 
 Speed/Torque switching
!
! Pattern operation continuation signal 
 No function assigned
!
 Pattern operation trigger signal 
 No function assigned
!
 External thermal error 
 No function assigned
!
 Communication priority cancel 
 No function assigned
!
 HD operation retention 
 Rapidest deceleration command
!
 PID differentiation/integration clear 
 Preliminary excitation
*4
!
! PID forward/reverse switching 
 Braking request
!
! Forced continuous operation 
 No function assigned
!
 Specified speed operation 
 Brake answer back input
!

Acceleration/dece leration su spend sign al

 No function assigned
!
 Power failure synchronized signal 
 Traverse permission signal
!
 My function RUN signal 
 (reservation)
!
 Auto-tuning signal ���  V/f ratio switching
!
 Speed gain switching   Manual torque boost switching signal
!
! Servo lock signal
*1: Valid when HOQF(Frequency setting mode selection 1) is set at  (Motor operat ed pot mop setting).
The frequency setting range is between =~WN(Upper limit frequency). The a cceleration/deceleration time with respect
to the frequency setting remains CEE/FGE, unless switching between accele ration and deceleration is performed.
*2: To switch acceleration/deceleration pattern, V/f pattern, torque limit 1~4, give the following signals to switching functions.
Switching signal 1 Switching signal 2
Acceleration/deceleration1, V/f 1, torque limit 1 OFF OFF
Acceleration/deceleration2, V/f 2, torque limit 2 ON OFF
Acceleration/deceleration3, V/f 3, torque limit 3 OFF ON
Acceleration/deceleration4, V/f 4, torque limit 4 ON ON
*3: If , (F: Forward run command) or , (R: Reverse run command) is a ssigned at the same time, this function has a
priority.
*4: After the motor slows down and comes to a full stop at a pre-excitation command, th e motor is set free momentarily to
bring it into a pre-excitation state.
This function should not be used when H is set to or . Or the inverte r might malfunction.
*5: Do not set the function " Permission of parameter editing" into the parameter H~H (without option)
and~H. If it is setted, can not reset the setting.