Toshiba VF-AS1 instruction manual E6581301

							E6581301
	<Basic operating>
	Step		Setting				Parameter
	1	Set the pattern operation selection			￿￿￿￿=￿ (Disabled)
		parameter at “Enabled.”			￿ (Pattern operation enabled, setting in seconds)
					￿ (Pattern operation enabled, setting in minutes)￿
	2	Set all necessary operation frequencies.			￿￿￿~￿￿￿		(Preset speed operation frequencies 1~7)
		In addition, set frequencies for preset			￿￿￿￿~￿￿￿￿ (Preset speed operation frequencies 8~15)
		speed operation.			￿￿￿￿		(Preset speed operation mode selection)
					￿￿￿￿~￿￿￿￿ (Preset speed operation frequency 1~15
							operation mode)
	3	Set the required operation time at each of			￿￿￿￿~￿￿￿￿ (Operating time at each speed)
		the set operation frequencies. Using
		￿￿￿￿, select the unit of time to be set
		(second or minute).
	4	Set the sequence of each speed.
		This sequence following three methods.
		(1) Select a run/stop operation from the			→ ￿￿￿￿=￿ (Patterned operation canceled during stop)
			pattern operation mode.		* Pattern operation is reset by stop/switching
						operation before operating restarts.
						=￿ (Patterned operation continued during stop)
					* Pattern operation is started by stop/switching
						operation. The system stops temporarily on
						completion of every routine, then proceeds to the
						next routine.
		(2) Select a pattern group, and then set			→ ￿￿￿￿		(Number of repetitions of pattern group
			the sequence of each speed.		1)
6					￿￿￿￿~￿￿￿￿ (Pattern group 1 selection 1~8)
					￿￿￿￿		(Number of repetitions of pattern group
		(3) According to the required parameter			2)
			group, select pattern operation		￿￿￿￿~￿￿￿￿ (Pattern group 2 selection 1~8)
			selection 1 or 2 from input terminal		→ ￿￿￿￿~￿￿￿￿=￿￿, ￿￿ (Pattern operation selection 1)
			function selection ￿￿￿￿ to ￿￿￿￿.				=￿￿, ￿￿ (Pattern operation selection 2)
			Selecting pattern operation				=￿￿, ￿￿ (Pattern operation
			continuation signals makes it possible				continuation signal)
			to select a start/stop method.				=￿￿, ￿￿ (Pattern operation trigger
							signal)
	5	Monitor displayed during pattern operation
		Specify the pattern operation monitor item (￿￿ to ￿￿) that you want to display as a status monitor item
		(￿￿￿￿ to ￿￿￿￿). This setting makes the inverter display the pattern operating status.
			Condition	Marking			Specification
			Pattern and pattern group	￿￿￿￿		(A): Number of the pattern group
					(A) (B)	(B): Number of the pattern
			Pattern group – remaining	￿￿￿￿￿		Indicates that pattern operation has been
			number of repetitions			performed 123 times.
			Operation preset speed	￿￿		Frequency reference with preset speed 1 data.
			Remaining time of the current	￿￿￿￿		Current pattern is finished in 1234 sec.
						Operation time is set for infinity or the system
			pattern operation	￿￿￿￿
						is waiting for the next step command.

F-56