Monitoring the status, Led | Toshiba VF-AS1 manual

!

E6581301

8.2Monitoring the status

8.2.1Status monitor under normal conditions

In this mode, you can monitor the operation status of the inverter.

To monitor the inverter when it is normally running, press the MODE key twice and the current status is indicated on the LED display.

Setting procedure (EX.: operation at 60 Hz)

*1

*2

*3

*4

*5

*6

8 *7

*8

*9

[Note 4]

	Commun		Key	LED
	ication	Item displayed	Key	LED	Description
	ication	Item displayed	operated	display	Description
	No.		operated	display
	No.
		Standard monitor			The output frequency is displayed (during operation).
	-	Standard monitor			(When standard monitor display selection is set
	-	mode			(When standard monitor display selection is set
		mode			to [Output frequency])
					to [Output frequency])
	FE01	Setting monitor	MODE		The first basic parameter “History function ()” is
		mode			displayed.

	FE01	Status monitor mode	MODE		The rotating direction is displayed. (:Forward run,
	FE01	(Rotating direction)	MODE		:Reverse run)

	-	Frequency			The operation frequency command value is displayed.
		command value			(When =, Frequency command)
	-	Output current			The inverter output current (load current) is displayed.
					(When =, Output current)
	-	Input voltage (DC			The Inverter DC voltage (default setting: unit %) is
		detection)			displayed.(When =, Input voltage) [Note 3]
	-	Output voltage			The inverter output voltage (default setting: unit %) is
	-	Output voltage			displayed.(When =, output voltage)
	-	Torque			The torque is displayed.
	-	Torque			(When = torque)
		Regenerative			The regenerative braking resistance overload factor is
	-	braking resistance			displayed.
	-	overload factor			(When =, regenerative braking resistance
		(PBrOL data)			overload factor)
		Inverter overload			The inverter overload factor is displayed.
	-	factor			The inverter overload factor is displayed.
		(OL1 data)			(When =, inverter overload factor)
		(OL1 data)
		Motor overload			The motor overload factor (default setting: unit %) is
	-	Motor overload			displayed.
	-	factor			displayed.
		factor			(When =, Motor overload factor)
					(When =, Motor overload factor)
	FE00	Output frequency			The output frequency is displayed.

		Input terminal			The ON/OFF status of each of the control signal input
		Input terminal			terminals (F, R, ST, RES, S1, S2, S3, RR/S4) is
		information 1			terminals (F, R, ST, RES, S1, S2, S3, RR/S4) is
		information 1			displayed in bits.
					displayed in bits.
	FE06	Input terminal			The ON/OFF status of each of the optional control signal
		information 2			input terminals (LI1, LI2, LI3, LI4) is displayed in bits.
		Input terminal			The ON/OFF status of each of the optional control signal
		information 3			input terminals (LI5, LI6, LI7, LI8) is displayed in bits.
		Output terminal			The ON/OFF status of each of the control signal output
		information 1			terminals (OUT1, OUT2, FL) is displayed in bits.
	FE07	Output terminal			The ON/OFF status of each of the optional control signal
		Output terminal			output terminals (OUT3, OUT4, R1, OUT5, OUT6, R2,
		information 2			output terminals (OUT3, OUT4, R1, OUT5, OUT6, R2,
		information 2			R3, R4) is displayed in bits.
					R3, R4) is displayed in bits.
	(Continued overleaf)

H-2

Image 220

Toshiba VF-AS1 Monitoring the status, Status monitor under normal conditions, Setting procedure EX. operation at 60 Hz

Contents

New High-performance inverter Safety precautions Limits in purpose General Operation Transportation & installation Wiring Reference When retry function is selected Operations Maintenance and inspection II. Introduction Contents 13.1 13.214.3 14.4 24.1 24.224.3 25.1 36.2 36.336.4 36.5 10.6 10.6.110.6.2 12.1 Contents of the product code Check the productExplanation of the type and form written on the label Type Form Structure of the main body Names and functions 1 Outside view Mode key MON lamp RS485 connector/coverRUN lamp PRG lamp Main circuit terminal Switch Grounding terminal M5 screw Screw hole for EMC plateM5 screw E6581301 VFAS1-4300PL, 4370PL VFAS1-4132KPC VFAS1-4110KPCVFAS1-4160KPC VFAS1-4500KPC Control circuit terminal block Detaching the coverControl circuit terminal block is common to all equipment For details on all terminal functions, refer to Section E6581301 E6581301 Grounding capacitor switching method 200V! 18.5#22kW 400V! 22kW 200V/400V Class Small E6581301 Installing the DC reactor Comparisons with commercial power operation Adjusting the overload protection levelMotors Operation in the low-speed area Braking a motor when power supply is lost High-speed operation at and above 50Hz/60Hz rated frequencyMethod of lubricating load mechanisms Low loads and low inertia loads Inverters If power supply distortion is not negligible DisposalMeasure to take against leakage Current Effects of leakage current across ground Affects of leakage current by cable length Affects of leakage current across supply linesRemedies Installation Installation environment How to install Resistors Place far away from VF-AS1 Inverter Standard installation Side-by-side installation 4001Without top cover5001Without top cover 6001Without top cover Ambient temperature Continuous Ambient temperature 4001Without top cover4001With top cover F631=0 Output Carrier frequency Ambient temperature 4001With top cover5001With top cover With top cover 6001Without top cover Current E6581301 Installing more than one unit in a cabinet Connection equipment Wiring Control and main power supplyPreventing radio noise Standard connections Between PO and PC Standard connection diagram sink logic Standard connection diagram sink logic Standard connection diagram sink logic Standard connection diagram source logic Standard connection diagram source logic Standard connection diagram source logic Power supply and motor connections Description of terminalsMain circuit terminals Connection with peripheral equipment RES RR/S4 PLC VI/IOUT1 OUT2 +SU FLAFLB FLC Source logic Sink logic1Be sure to short across NO-CC SOURCE! INT/PLC 3 RS485 communication connector Operations Setting/monitor modes VF-AS1 has the following three setting/monitor modes Simplified operation of the VF-AS1 Example of standard connectionMccb OFF + RR/S4 CCA Frequency setting+ VI/II Setting the frequency using input voltage 0~10Vdc Setting the frequency using input voltage 0~±10Vdc+ VI/II CCA + RX CCA Press the Enter key to display the first extended parameter Default settingPress Key to change to Panel operation Set frequencyMotor starts Stop the motor Selecting a stop mode with the operation panel Example of operation panel controlDeceleration stop 1 Press the Stop key Press the Stop key again Searching and setting parameters Quick mode Easy How to set parameters Setting parameters in the selected quick mode Setting parameters in the standard setting mode Changed parameter search function Setting methods History functionHistory function Function Setting acceleration/deceleration time When load is smallWhen load is large Automatic acceleration/deceleration Manually setting acceleration/deceleration time Constant torque characteristics default settingIncreasing starting torque Automatic torque boost If vector control cannot be programmed Automatic torque boost and V/f control mode selectionIncreasing torque manually V/f constant control Setting parameters by operating method Automatic function settingFrequency Voltage/current Setting on Default Automatically programmed functions and parameter set values Command mode selection Frequency setting mode selection Selection of operation modeCommand mode selection VI/II input RR/S4 inputRX input Operation panel input Set this parameter at terminal board Any setting is valid Preset speed operationRun/stop Press the RUN and Stop keys On the operation panel Run/stop ON/OFF of terminals F-CC/R-CC Standby connection of terminals ST and CC Or 40~20mAdc Constant torque characteristics Normal way of use Selecting control modeControl mode selection Torque boost rate is adjusted automatically Decreasing output voltageMotor constant must be set Output frequency Hz Base frequency Setting of V/f characteristic arbitrarily Setting of V/f control mode selection = V/f 5-point setting Setting of V/f control mode selection = PM control Base frequency voltage 5-point setting Output voltageOperating a permanent magnet motor VF5 VF4 VF3 VF1 VF2 Precautions on automatic torque boost mode or vector control Manual torque boost-increasing torque boost at low speeds Base frequencyManual torque boost Base frequency Base frequency voltage Maximum frequency Upper limit and lower limit frequenciesMaximum frequency Upper limit frequency Lower limit frequency Setting frequency command characteristics Preset speed operation speeds in 15 steps RR/S4 RR/S4-CC ST-CC OFF Selecting forward and reverse runs operation panel only Forward/reverse run selection Setting the electronic thermal Explanation of terms Using a VF motor motor for use with inverter First basic parameter History function is displayedPress either the key or the key to change the parameter to = motor rated current/inverter output rated current x Setting the motor overload starting level Motor 150%-overload time limitOperation frequency Frequency 01Hz *1 No less than Motor overload Inverter overload characteristics Changing the display unit % to a ampere/V volt Current/voltage unit selection Meter setting and adjustment VF-AS1 Regenerative braking resistance overload factor OLr data Adjustment is complete. and the frequency are displayed Press either Key to selectPress the Enter key to display the operation frequency Display returns to its original indications Select the AM terminal meter adjustment by pressing the key Press the Enter key to switch to the data display modeReturn the parameter setting to output current display Display mode. When standard monitor display selection = Gradient bias adjustment of analog monitor output PWM carrier frequency Trip-less intensification Refer to .4.4, Current reduction curve Below 130% Operation and application of the auto-restart function Synchronized acceleration/deceleration signal An example of setting when = Dynamic regenerative braking For abrupt motor stop Connecting an external braking resistor optional External braking resistor with a thermal fuse optional When a using braking resistor without thermal fuse Capacities of 400V-200kW or more Selection of braking resistor option and braking unit VFAS1-4280KPC Minimum resistance of connectable braking resistors Standard default setting Factory default setting50Hz default setting = 60Hz default setting = Default setting = Reset of user-defined parameters =Acceleration/deceleration time setting 0.01 to 600.0 sec. = Acceleration/deceleration time setting 0.1 to 6000 sec. = Automatic edit function Press Key to selectKey to change the parameter displayed. Press Key to search for parameters in reverse direction Quick mode/standard setting mode switching function = Quick modeStandard setting mode Easy key function Operation panel/remote key function = Shortcut key function =Peak hold function = Low-speed signal Low-speed signal output frequency Low-speed signal output InvertedConnection diagram SW1 set to sink logic P24 OUT1 or OUT2 Output terminal setting Parameter setting of frequency and detection band Parameter setting of output terminal selection Input signal selection Parameter settingForward run signal Reverse run signal Valid command Command from the terminal board ST-CC Output frequency Hz Set frequency Panel key Forward runCC Jog run Terminal function selection Setting of contact input terminal functionModifying input terminal functions PLC Connection method 1 a-contact input Servo lock status Basic parameters Using the V/f adjustment function Adjustment rateManual torque boost Base frequency Thermal protection level S1-CC S2-CC Parameters selected 5-point setting VF3 frequency 5-point setting VF3 voltage V/f 5-point settingSwitching with input terminal board = Automatic switching by means of switching frequencies = Priority is given to Command set With Operation frequency DC braking DC braking start frequency DC braking current DC brakingDC braking time Forward/reverse DC braking priority control ~ ~ ~ ~ Motor shaft fixing control E6581301 Operation signal F-CC SW1 set to sink logic Time s Time limit for lower-limit frequency operation Jog run mode ST-CC S3-CC Status monitor mode «Sample sequence diagram 2 Adjustment with pulse signals» Adjustment with pulse signals Parameter-setting example Jump frequency Jump frequency jumping resonant frequenciesJumping width Preset speed operation frequency 8 to Preset speed operation frequenciesPreset speed operation frequencies 8 to Trip-less intensification Output Frequency Overvoltage stall protection Voltage Output voltage adjustment Supply voltage correction Reverse run prohibition Reverse run prohibition selection Drooping controlOutput voltage waveform selection Gain1 Braking function Light-load high-speed operation functionCreeping time Hoisting torque bias input Creepinjg frequency Acceleration/deceleration suspend function Reverse run Forward run Commercial power/inverter switching Stall control Timing chart example PID control switching Process lower limit PID control feedback control signal selectionPID control Differential D gain External connection Types of PID control interfaceProcess value DC0~10V RR/S4 CCA VI/II Setting the PID control Adjust PID control gainFast response Low proportional gain Adjusting the analog command voltage and current Setting motor constants Stop position control function Settings YESBase frequency Voltage Rated capacity Not set correctly. Check their Setting auto-tuning Examples of setting the motor constants Exciting strengthening coefficient Stall prevention factor Reference selection Torque controlSpeed limit torque=0 band E6581301 Torque limit Power Regenerative Running 10V +10V RX-CCA RR/S4 -CCA, VI/II-CCAVI/II-CCA Torque limit level Torque is h eld at a limit level evenAfter the mechanical brake is released Power running stall continuous trip detection time Regenerative braking stall prevention mode selectionStall prevention control switching Stall prevention function Current and speed control adjustment Max output voltage modulation rate Fine adjustment of frequency setting signal Operating a synchronous motor Acceleration S-pattern lower limit adjustment Deceleration S-pattern lower limit adjustmentAcceleration/deceleration Deceleration time Acceleration time Acceleration/deceleration switching signal Set frequency Pattern operation E6581301 Preset speed mode ~ Preset speed operation modesPattern operation finished OFF signal Function selection Setting of stall prevention level Stall prevention level Protection functions Emergency stop Emergency DC braking control time Output phase failure detection Output phase failure detection mode selection Function OFF ON! OFF Cooling fan control selection Cumulative operation time alarm setting Braking answer waiting time 33.18 VI/II analog input wire breakage detection level Rush current suppression relay activation time DC voltage Rush current suppression relay Refer to 5.19 for details Ground fault detection selection Override Disconnection detection of remote keypad Ex.1 = VI/II input, = disabled Ex.2 = VI/II input, = disabled Adjustment parameters SW2 0-10V/0-20mA side FM terminals setting exampleLarge gain Resetting method Operation panel parameter Value displayed Monitor-displayed or parameter-set frequency When is not , and is not When is not , and is disabledAn example of setting When is , and is Example of setting Tracing functions Trace selection Trace cycle Trace data To acquire trace data at the time of triggering = Acquisition of trace data Trace data communication number Integrating wattmeterRelationship between pointer and data Send waiting time 2-wire RS485 Communication function Wire RS485 No action Common to 2-wire RS485 and 4-wire AlarmAlarm No action TOSHIBA, Modbus E6581301 ~ ~ Response data INV → host Wiring Data Master → Slave Data Host →!INV Alarm No action Trip Toshiba Modbus E6581301 Traverse function My functionInput function target 11~ My function selection ETB003Z ETB004ZVEC007Z DEV002Z External operation Case of control panel operation command inputCase of control panel operation the frequency Functions of input terminals in case of sink logic Input terminal function selection RR/S4 Preset speedLI1~LI8 Inverter Input terminal Programmable controller COM Acceleration/deceleration2, V/f 2, torque limit Acceleration/deceleration3, V/f 3, torque limit Output terminal function Selection Low-speed signal Functions of output terminals incase of sink logicFLA FLB FLC OUT1 OUT2 E6581301 PROFIBUS/DeviceNet/CC Stop Response time setting Setup of input terminal operation timeAnalog input filter Setup of external speed command analog signal Setup by analog input signals RR/S4 terminal Running frequency characteristicConnection and calibration Frequency meter Setup by analog input signals VI/II terminal ~10Vdc Setup by analog input signals RX terminal Run/stop setup Screen composition in the status monitor mode Monitoring the operation status Setting procedure EX. operation at 60 Hz Monitoring the statusStatus monitor under normal conditions LED OFF Input terminal information Data bit of communicationNo. FE06 No. FE07 Unit times Display of detailed information on a past tripPress this key to return to past trip Changing status monitor function MON1 MON2 Default Item displayed Marking Unit Panel FE56 01% FD85COUNT1 FD86 Display of trip information Trip code display Error code Description Communication/Error code Direction of rotation when the trip occurred is Monitor display at trippingFE01 Direction of rotation Displayed.Forward run, Reverse run Mode Display of alarm, pre-alarm, etc How to cope with the CE standard EMC directive Measures to satisfy the EMC directive Models with a built-in EMC filter Ex. Countermeasure inverter wiring E6581301 VFAS1-4160KPC~ 100 EMF3-4600J VFAS1-4355KPC~ 100 EMF3-4600J × Operation with external signals Power supply wiring Shielded cablessOUT2, CC Low-voltage directive Accessories for countermeasureMeasures to be taken to satisfy the low-voltage directive Measures to be taken to satisfy the UL/CSA standards AIC, Fuse and Wire sizes Applicable Inverter model 10.1 ! Selection of wiring materials and devices AWGVFAS1-4355KPC VFAS1-4400KPC MCC Magnetic contactor Input currentA Selection of wiring equipmentVoltage Applicable Without Inverter model Reactor Installation of a magnetic contactor Installation of an overload relayMagnetic contactor in the primary circuit Magnetic contactor in the secondary circuit Application and functions of options ACL E6581301 GTR7 Supply backup DCL Suppression Supply Filter *4 Backup CPS002Z Table of optional devices Functions of Add-on type options Functions of Plug-in type options PG feedback option 6 7 Model VEC004Z, VEC005Z, VEC006Z How to install Connection of a DC power supply and other electric units Connection of a single-phase 200V power supplyWhen using the inverter along with a DC power supply MCR-2550×5 parallel Required No required Connecting fans for a separate power supply Power consumed by the fansVFAS1 VFAS1-4200KPC4280KPC VFAS1-4355KPC, 4400KPC, 4500KPC Vector control Title Cation Function Adjustment range Speed Torque Control Reference Basic parameter 2/4 Communi Speed Torque Reference E6581301 Setting Braking ST-off Overload detect Function Disabled SelectionBasic parameter 4/4 Communi 0304 Dynamic braking Setting unit Default Write during ~155 *1 Disabled 0112 0110 Always on function selection ~155 *1 Disabled 0111Terminal function selection Communi Speed Torque Reference Vector control Title Function Adjustment range F 5-point setting CommuniDefault Speed Torque Reference Cation E6581301 DC braking Communi Default Speed Tripless intensification setup 2/2 Communi 0307 Selection Disabled Correction of supply voltage0308 Dynamic braking resistance ~1000 0.1 Disabled 0309 01~600.0kW 01/0.01 Disabled 0310 4enabled Enabled Functions for lift 2/2 Communi Process increasing rate speed type Motor constant Communi Speed Torque E6581301 Torque limit 2/2 Communi E6581301 Acceleration/deceleration 2 2/2 Communi E6581301 Bootp Dhcp E6581301 55~100% Disabled Protection functions 2/2 Communi Cation Function Adjustment range Meter output 2/2 Communi E6581301 Operation panel parameters 2/3 Communi Control 0751 Quick registration parameter ~999 *1 Enabled 0752 Quick registration parameter ~999 *1 Enabled 0753 07540755 Quick registration parameter ~999 *1 Enabled 0756 Quick registration parameter ~999 *1 600 Enabled Enabled RS485 Communication function 1/40TOSHIBA 1MODBUS 0812 Point 1 frequency ~ Hz 0.01 0813 Point 2 setting ~100%0814 Point 2 frequency ~ Hz 0.01 Vector control Title Communi Function Adjustment range Enabled Wire RS4850000~ Enabled 0842 0000~ Enabled 0843 E6581301 My function 1/5 Communi 2STN 4ANDN6ORN 22CLRN My function 3/5 Communi 1VI/II Control 0Disabled My function 5/5 Communi Communi Control Ion Function Communicat Trip retention 01Hz FD17 FE17 01% FE56 FD85 E6581301 E6581301 LOW 120 121 122 123124 125 126 127 242 243 244 245246 247 248 249 Torque Base Acc/dec Dynamic Models and their standard specifications Standard specifications small/medium capacity types Standard specifications large capacity types However, this is unnecessary for DC input specifications Common specification Voltage/frequency LED Outside dimensions and weight Outline drawing Fig. a Fig. G Fig. K Fig. O Before making a service call Trip information and remedies Trip causes/warnings and remedies Input voltage fluctuates abnormally E6581301 CPU2 E6581301 E6581301 Method of resetting causes of trip If the motor does not run while no trip message is displayed How to check other troubles More Regular inspection Check points Periodical inspection Check items Replacement of expendable parts Standard replacement cycles of principal parts Making a call for servicing Keeping the inverter in storage Warranty Disposal of the inverter