Toshiba VF-AS1 instruction manual PROFIBUS/DeviceNet/CC

!				E6581301!
	Parameter setting
	Positive	Negative	Function	Operation output specifications (in case of positive logic)
	logic	logic
	￿￿￿	￿￿￿	Over-torque detection	ON:The state that torque component is ￿￿￿￿, ￿￿￿￿ set
				value or larger continued more than ￿￿￿￿ set value.
			Braking resistor	ON:A certain rate of braking resistor overload trip (￿￿￿)
	￿￿￿	￿￿￿		detection time is over.
			overload pre-alarm
				OFF:The detection time is within a certain limit.
	￿￿￿	￿￿￿	In emergency stop	ON:In emergency stop operation (￿ is indicated).
				OFF:The detection time is within a certain limit.
	￿￿￿	￿￿￿	In retry	ON:In retry operation (￿￿￿￿ is indicated).
				OFF:No retry operation is performed.
	￿￿￿	￿￿￿	Pattern operation	ON:In normal operation or pattern operation has finished.
			switching output	OFF:In pattern operation.
	￿￿￿	￿￿￿	PID deviation limit	ON:PID deviation is in ￿￿￿￿ or ￿￿￿￿ set value.
	￿￿￿	￿￿￿	Run/Stop	ON:Running frequency is output or DC injection breaking (￿￿)
				is performed.
			Serious failure (OCA,	ON:Serious failure (￿￿￿, ￿￿￿, ￿￿, phase failure, abnormal
				output, short-circuit) is detected.
	￿￿￿	￿￿￿	OCL, EF, phase failure,
				OFF:Inverter has recovered from serious failure. (Serious
			etc.)
				failure has been reset)
			Light failure (OL, OC1,	ON:Light failure (￿￿, ￿￿￿, ￿￿￿, ￿￿￿, ￿￿) is detected.
	￿￿￿	￿￿￿		OFF:Inverter has recovered from light failure. (Light failure has
			2, 3, OP)
				been reset)
			Commercial
	￿￿￿	￿￿￿	power/inverter	Refer to Section 6.19.
			switching output 1
			Commercial
	￿￿￿	￿￿￿	power/inverter	Refer to Section 6.19.
			switching output 2
	￿￿￿	￿￿￿	Cooling fan ON/OFF	ON:Cooling fan is in operation.
				OFF:Cooling fan is off operation.
	￿￿￿	￿￿￿	In jogging operation (In	ON:In jog run
			jog run)	OFF:In normal operation
			Operation	ON:In operation by terminal board.	7
	￿￿￿	￿￿￿	panel/terminal board
				OFF:In operation by operation panel.
			operation switching
			Cumulative operation	ON:Cumulative operation time is beyond the ￿￿￿￿ set value.
	￿￿￿	￿￿￿		OFF:Cumulative operation time is less than the ￿￿￿￿ set
			time alarm
				value.
	￿￿￿	￿￿￿	PROFIBUS/DeviceNet/CC-	ON:Communication error occurred.
			Link communication error	OFF:Communication error is canceled (reset).
			Forward/reverse	OFF:In forward operation. ON:In reverse operation.
	￿￿￿	￿￿￿		It output command status while operation is stopped.
			switching
				(When command status is not active, It will be "OFF")
				ON:In operable status (exclude during deceleration stop) or
	￿￿￿	￿￿￿	Ready for operation 1	operation can be started with frequency command input as an
				operation switching answer-back.
				OFF:In inoperable status.
				ON:In operable status or operation can be started with ST and
	￿￿￿	￿￿￿	Ready for operation 2	RUN signals and frequency command input.
				OFF:In inoperable status.
	￿￿￿	￿￿￿	Brake release (BR)	Output the braking signal according to the brake sequence.
				ON:More than one of alarm, pre-alarm, undervoltage, low
				current over-torque, poor control power supply, PID deviation
	￿￿￿	￿￿￿	In (pre-)alarm status	limit, abnormal frequency setting or torque limit have occurred
				or detected.
				OFF:All the alarms above are canceled.
	￿￿￿	￿￿￿	Forward speed limit	ON:Forward operation speed is ￿￿￿￿ set value or over.
			(torque control)	OFF:Forward operation speed is less than ￿￿￿￿ set value.
	￿￿￿	￿￿￿	Reverse speed limit	ON:Reverse operation speed is ￿￿￿￿set￿ value or over.
			(torque control)	OFF:Reverse operation speed is less than ￿￿￿￿ set value.
	￿￿￿	￿￿￿	Inverter healthy output	ON and OFF are alternately output at intervals of 1 second.
	￿￿￿	￿￿￿	RS485 communication	ON:Communication error occurred.
			error	OFF:Communication error is canceled (reset).
	￿￿￿	￿￿￿	Error code output 1
	￿￿￿	￿￿￿	Error code output 2
	￿￿￿	￿￿￿	Error code output 3	Output the error code in 6-bit.
	￿￿￿	￿￿￿	Error code output 4
	￿￿￿	￿￿￿	Error code output 5

G-7