Toshiba VF-AS1 instruction manual Stop

	!					E6581301
		Parameter setting
		Positive	Negative		Function	Operation output specifications (in case of positive logic)
		logic	logic
		￿￿￿	￿￿￿	Error code output 6
		￿￿￿	￿￿￿	Specified data output 1
		￿￿￿	￿￿￿	Specified data output 2
		￿￿￿	￿￿￿	Specified data output 3
		￿￿￿	￿￿￿	Specified data output 4		Output of the designated data in 7-bit.
		￿￿￿￿	￿￿￿￿	Specified data output 5
		￿￿￿￿	￿￿￿￿	Specified data output 6
		￿￿￿￿	￿￿￿￿	Specified data output 7
		￿￿￿￿	￿￿￿￿	Light load output		ON:Load is equal to ￿￿￿￿~￿￿￿￿ set values or less.
		￿￿￿￿	￿￿￿￿	Heavy load output		ON:Load is larger than ￿￿￿￿~￿￿￿￿ set value.
		￿￿￿￿	￿￿￿￿	Positive torque limit		ON:Positive torque is over the positive torque limit level.
		￿￿￿￿	￿￿￿￿	Negative torque limit		ON:Negative torque is over the positive torque limit level.
		￿￿￿￿	￿￿￿￿	Output for external rush		ON:External rush suppression relay is actuated.
				suppression relay
		￿￿￿￿	￿￿￿￿	Completion of stop		ON:Stop positioning has been completed.
				positioning
		￿￿￿￿	￿￿￿￿	L-STOP		ON:Operation at the lower limit frequency is performed
						continuously.
		￿￿￿￿	￿￿￿￿	Power failure		ON:Power failure synchronized operation is performed.
				synchronized operation
		￿￿￿￿	￿￿￿￿	Traverse in progress		ON:Traverse operation is performed.
		￿￿￿￿	￿￿￿￿	Traverse deceleration in		ON:Traverse deceleration operation is performed.
				progress
		￿￿￿￿	￿￿￿￿	Part replacement alarm		Alarm:The time of replacement of parts is approaching.
		￿￿￿￿	￿￿￿￿	Over-torque pre-alarm		ON: 70% of the ￿￿￿￿ or ￿￿￿￿ setting level is detected.
		￿￿￿￿	￿￿￿￿	Frequency command 1/		ON:Frequency command selection 2 is selected.
				2 selection
		￿￿￿￿	￿￿￿￿	Failure FL (Except		ON:A trip other than emergency stop has occurred.
				emergency stop)
		￿￿￿￿	￿￿￿￿	My function output 1		ON:My function output 1 is ON.
7		￿￿￿￿	￿￿￿￿	My function output 2		ON:My function output 2 is ON.
		￿￿￿￿	￿￿￿￿	My function output 3		ON:My function output 3 is ON.
		￿￿￿￿	￿￿￿￿	My function output 4		ON:My function output 4 is ON.
		￿￿￿￿	￿￿￿￿	My function output 5		ON:My function output 5 is ON.
		￿￿￿￿	￿￿￿￿	My function output 6		ON:My function output 6 is ON.
		￿￿￿￿	￿￿￿￿	My function output 7		ON:My function output 7 is ON.
		￿￿￿￿	￿￿￿￿	My function output 8		ON:My function output 8 is ON.
		￿￿￿￿	￿￿￿￿	My function output 9		ON:My function output 9 is ON.
		￿￿￿￿	￿￿￿￿	My function output 10		ON:My function output 10 is ON.
		￿￿￿￿	￿￿￿￿	My function output 11		ON:My function output 11 is ON.
		￿￿￿￿	￿￿￿￿	My function output 12		ON:My function output 12 is ON.
		￿￿￿￿	￿￿￿￿	My function output 13		ON:My function output 13 is ON.
		￿￿￿￿	￿￿￿￿	My function output 14		ON:My function output 14 is ON.
		￿￿￿￿	￿￿￿￿	My function output 15		ON:My function output 15 is ON.
		￿￿￿￿	￿￿￿￿	My function output 16		ON:My function output 16 is ON.
		￿￿￿￿	￿￿￿￿	Always OFF (for terminal		Output signal always OFF
				signal tests)
		Note 1: “ON” in positive logic			: Open collector output transistor or relay is turned on.
		“OFF” in positive logic			: Open collector output transistor or relay is turned off.
		“ON” in negative logic			: Open collector output transistor or relay is turned off.
		“OFF” in negative logic : Open collector output transistor or relay is turned on.
		Note 2: Alarm output check conditions are as follows.
		(1) Undervoltage detected :To be checked during operation.
		(2) Low current detected			: To be checked during operation command.
		(3) Overtorque detected			: To be checked always.

■Sink logic/source logic

Sink logic and source logic (logic of input/output terminal) can be switched to each other.

￿ For details, refer to Section 2.3.2.

G-8