Toshiba VF-AS1 instruction manual Display of trip information, Trip code display

! E6581301!

8.4Display of trip information

8.4.1Trip code display

If the inverter trips, an error code is displayed to suggest the cause. In the status monitor mode, the status when the

inverter trip is held.

■Display of trip information

Error code	Description	Communication/Error code
		Communication No.:FC90
￿￿￿￿	Overcurrent during acceleration	1
￿￿￿￿	Overcurrent during deceleration	2
￿￿￿￿	Overcurrent during fixed speed operation	3
￿￿￿￿￿	Overcurrent flowing in element during acceleration	37
	(Overheat)
￿￿￿￿￿	Overcurrent flowing in element during deceleration	38
	(Overheat)
￿￿￿￿￿	Overcurrent flowing in element during fixed speed	39
	(Overheat)
￿￿￿￿￿￿￿	U-phase arm overcurrent	5
￿￿￿￿￿￿￿	V-phase arm overcurrent	6
￿￿￿￿￿￿	W-phase arm overcurrent	7
￿￿￿￿￿	Overcurrent (Loaded side overcurrent at start time)	4
￿￿￿￿	Dynamic braking element overcurrent (200V-55kW or	36
	larger, 400V-90kW or larger)
￿￿￿￿	Overheating	16
￿￿￿￿	Thermal trip stop command from external device	46
￿￿￿￿￿	Inverter overload	13
￿￿￿￿￿	Motor overload	14
￿￿￿￿￿	Dynamic braking resistor overload	15
￿￿￿￿￿	Overvoltage during acceleration	10
￿￿￿￿￿	Overvoltage during deceleration	11
￿￿￿￿￿	Overvoltage during fixed speed operation	12
￿￿￿￿	Overtorque	32	8
￿￿￿￿	Low current operation	29
￿￿￿￿￿	Undervoltage (main circuit power supply)	30
￿￿￿	Emergency stop	17
￿￿￿￿￿￿	E E P ROM fault (writing error)	18
￿￿￿￿￿￿	Initial read error (parameter initialization)	19
￿￿￿￿￿￿	Initial read error (parameter initialization)	20
￿￿￿￿￿	Ground fault	33
￿￿￿￿￿		34
￿￿￿￿￿￿	Output phase failure	9
￿￿￿￿￿￿￿	Input phase failure	8
￿￿￿￿￿￿	Inverter RAM fault	21
￿￿￿￿￿￿	Inverter ROM fault	22
￿￿￿￿￿￿	CPU fault	23
￿￿￿￿￿￿	Communication time-out error	24
￿￿￿￿￿￿	Gate array fault	25
￿￿￿￿￿￿	Output current detector error	26
￿￿￿￿￿	Optional unit fault	27
￿￿￿￿￿	Tuning error except Etn1~3	40
￿￿￿￿￿	￿￿￿￿ tuning error	84
￿￿￿￿￿	￿￿￿￿ tuning error	85
￿￿￿￿￿	￿￿, ￿￿￿, ￿￿￿￿~￿￿￿ setting error	86
￿￿￿￿￿￿	Inverter type error	41
￿￿￿￿￿￿	Analog input terminal overvoltage	42
￿￿￿￿￿￿	Sequence error	43
￿￿￿￿￿￿	Encoder error	44
(Continued overleaf)

H-9