Parker Products COMPAX-M /-S (L) manual Appendix Compax components, 206

Accessories and options

COMPAX-M / -S

Hand-held terminal

9.8

Appendix: COMPAX components

Mains module for COMPAX-M (excluding COMPAX 35XXM)

NMD10

Up to 3 x 500 V AC mains supply connection; direct mains supply operation 10 kW cont. output

NMD20

As NMD10, but with 20 kW continuous output; external ballast resistances available in 3 sizes.

HDY and HJ motors

You will find information about our range of motors in the motor documentation.

Motor and resolver cable for HDY and HJ motors

You will find motor and resolver cables on Page 46.

HAUSER linear unit and initiator equipment

HLE

80mm / 100mm / 150mm edge length (ask for information material!)

HPLA

80mm / 120mm / 180mm edge length (ask for information material!)

Initiator equipment

IVD1/.

Initiator distr.connect. w. cables of the f. lengths [m]:2.5; 5; 7.5; 10; 12.5; 15; 20; 25; 30; 35; 40; 45; 50

Initiator

PNP induction proximity switch: IN HE 521 506 with 6m cable.

Accessories

BDF2/01

Hand-held terminal for configuring and operating COMPAX

BDF1/03

External control panel with housing and without cable

BDF1/02

External control panel for front plate installation without cable

SSK6/..

Interface cable between contr. panel and COMPAX av.- in the following lengths: 2.5; 5; 7.5; 10; 12.5; in [m]

SSU1/01

RS232 - RS485 converters used in conjunction with option F1

GBK16

COMPAX – motor cable for disposing of SinCos.

Encoder: GBK11/..

Encoder cable for connecting COMPAX with an encoder.

EAM4/01

Encoder distributor for creating an encoder bus.

BUS1/01 Bus termination for encoder bus

SSK4/..

Connector cable between COMPAX and encoder distributor.

SSK7/..

Connector cable between encoder distributors or from an encoder emulation.

ASS1/01

Monitor box for outputting internal measurement signals with D1 option.

SSK1/..

RS 232

Interface cable for PC COMPAX, available in the following lengths:

2.5; 5; 7.5; 10; in [m]

Ballast resistors

NMD20:

BRM4: 0.57 kW-1.5 kW (15Ω

)

COMPAX 25XXS:

BRM5/01: 250W (56Ω

)

COMPAX 45XXS/85XXS:

BRM6/01: 450W (22Ω

)

COMPAX 35XXM:

BRM7/01: 2 kW (10Ω

)

COMPAX 1000SL

BRM8/01: 60W (100Ω

)

AC power filter

NMD10 / COMPAX 45XXS/85XXS: NFI01/02

COMPAX

25XXS: NFI01/01 or NFI01/06 (≤ 10m motor cable)

COMPAX 35XXM: NFI01/04 or NFI01/05 (with additional COMPAX-M)

NMD20: NFI01/03

COMPAX 1000SL: NFI01/01 (<50m motor cable) or NFI01/02 (>50m motor cable)

Motor outp. throttle

For motor lines >20m: MDR01/01 (16A/2mH) • MDR01/02 (30A/1.1mH) • MDR01/03 (>30A/0.64mH)

Ass. angle bracket:

MTS2: for indirect wall installation (heat sink in separate heat chamber) of COMPAX 02/05/15XXM

Fan set for NMD

Fan set for NMD10 and NMD20 to increase max. brake performance

ServoManager

To read and write COMPAX parameters and programs

Bus terminal

BUS1/01: Encoder bus

BUS2/01: HEDA

BUS3/01: Profibus

BUS4/01: RS485

BUS6/01: Encoder terminal for COMPAX 1000SL

Options

F1

4-wire RS485 interface

F5

2-wire RS485 interface

F2

Interbus S interface

F3

Profibus

F7

CS31

F8

CANopen

F4

CANbus

E2

Encoder interface with line terminator for individual connections.

E3

Encoder simulation for resolver

E4

Encoder interface without line terminator for creating an encoder bus.

E7

Analogue speed specification

only for COMPAX XX6X and COMPAX XX70 or for SPEED SYNC with COMPAX XX00!

A1

Absolute value sensor/HEDA

Cable to COMPAX: GBK1/.. lengths: 2.5; 5; 7.5; 10; 12.5; 15; 20; 25; 30; 35; 40; 45; 50 [m]

A4

HEDA f. COMPAX 1000SL

Cable COMPAX/COMPAX: SSK14/.. lengths :2.5; 5; 7.5; 10; 12.5; 15; 20; 25; 30; 35; 40; 45; 50 [m]

D1

D/A monitor

To output the measurement signals, you will need monitor box ASS1/01.

S1

Sensor interface for SinCos, single-turn or multi-turn

S2

Programmable sensor interface for SinCos multi-turn

S3

Sensor–interface for linear motors (cable: GBK18)

206