Parker Products COMPAX-M /-S (L) manual 224, Too hard E40

Appendix				COMPAX-M/S
Monitoring and limitation characteristics
No.	Cause	Action			Acknow-	Drive
					ledge with	volt.-free
E23	The current command is not allowed.	♦	Positioning command in the speed control mode.		Quit	no
		♦	Approach MZ in speed control mode.
		♦	Travel command when drive is switched off.
		♦	Hand +/- when an error is present.
		♦	More than 8 consecutive comparator commands
			(preparatory commands) in the data record
			memory.
E24	The speed selected is not valid.	Enter speed between 0...100%.			Quit	no
E25	The position selected is not valid.	Note end limits and "Software end limit monitoring"			Quit	no
		chapter in variant documentation.
E26	REPEAT without END or GOSUB	Insert END / RETURN command.			Quit	no
	without RETURN .
E27	Parameter must not be written.	Check parameter.			Quit	no
E29	Motor values missing.	Send unit to HAUSER.			Quit	yes
E30	Hardware fault.	Remove extreme external sources of fault.			Quit	yes
E31	Error in parameters.	Check parameter.			Quit	no
E32	Error in parameters.	Check parameter.			Quit	no
E33	Error in program memory.	Check data record memory.			Quit	no
E34	Error in program memory.	Check data record memory.			Quit	no
E35	Hardware fault.	Remove extreme external sources of fault.			Quit	no
E36	Hardware fault.	Faulty or incorrect unit hardware.			Power on	yes
E37	Auxiliary voltage +15 V missing.	Switch on again.			Power on	yes
E38	Voltage in intermediate circuit too	Increase braking and idle times / check mains power.			Quit	yes
	high; e.g. if braking output is too	COMPAX 25XXS: external ballast resistance
	high. Limits:	missing.
	COMPAX 25XXS: >400V	COMPAX 45XXS/85XXS: bridges X2/5 - X2/6
	COMPAX 10XXSL: >400V	missing.
	otherwise: >800V
		COMPAX 1000SL: Check value P134.
E39	Temperature too high (>85°), cycle	Increase acceleration times.			Quit	yes
	too hard.
E40	Input "Enable final stage" (45/85S: X3/1-/2; 1000SL X19/24-X19/12, 35XXM: X19/9-/10) not assigned				Quit	yes
	Only with COMPAX 35XXM, COMPAX 45XXS, COMPAX 85XXS and COMPAX 1000SL!
	Note!
	With E40 there is no braking delay; the final stage is immediately switched off.
	The input has a direct effect on the hardware.
E41	Final stage reports error.	Check motor and cable for ground fault, short circuit			Quit	yes
	COMPAX 35XXM: Short circuit of the	fault and function; remove extreme external sources
	ballast resistance or undervoltage	of fault.
	24V
	COMPAX 1000SL:
	Overvoltage or ballast switching
E42	Resolver / sensor error.	Check resolver cable and connector for correct			Quit	yes
		connections and faults.
		A special error code can be found in channel 67 of
		the optimization display. This means
		Error No. 1 ... 30: Sensor indicates error
		Error No. > 30:		COMPAX indicates error
		Error No. =160:		Sensor level too high
		Error No. =161: Sensor level too low
		(implement level adaptation using parameter P131)
E43	Output overloaded.	Check I/O cables, connectors and external circuits.			Quit	yes
		Note load limits (refer to start-up manual).
E44	Positive auxiliary voltage outside	Switch unit on again.			Power on	yes
	tolerances.
E45	Negative auxiliary voltage outside	Switch unit on again.			Power on	yes
	tolerances.
E46	Supply voltage +24V is too high.	Check +24V DC power unit.			Power on	yes
E47	Supply voltage +24V is too low.	Check +24V DC power unit.			Power on	yes

224

Please note: the operating instructions (pages 67 - 171) as well as the application examples (pages 225 - 237) can be found in the complete product manual which is available as PDF file on CD