Schneider Electric 58 TRX manual ATV58 Type FVC Specifications, 118

Altivar® 58 TRX AC Drives

Type FVC Specifications

ATV58 TYPE FVC SPECIFICATIONS

Environmental Specifications

Enclosure type	ATV58HU18N4 to U90N4: IP21/open type controllers according to Standard EN50178.
	ATV58HD12N4 to D79N4: Type 1 with conduit entry kit.◆
Resistance to vibrations	According to IEC 60068-2-6: 1.5 mm zero to peak from 3 to 13 Hz, 1 gn from 13 to 200 Hz
Resistance to shocks	According to IEC 60068-2-27: 15 g, 11 ms
Ambient pollution degree	ATV58HU18N4–D23N4: Pollution degree 2 conforming to IEC 600664-1, EN50718 and NEMA ICS-1, Annex A.
	ATV58HD28N4–D79N4: Pollution degree 3 according to IEC 600664-1, EN50718 and NEMA ICS-1, Annex A.
	Protect the drive controller against dust, corrosive gas, and falling liquid.
Max. relative humidity	95% maximum, non-condensing and without dripping according to IEC 60068-2-3. Provide heating system if there is
	condensation.
Maximum ambient	Storage: -25 to +65 °C (-13 to +149 °F)
temperature	Operation: Drive controllers ATV58HU18N4 to U90N4:
	-10 to +50 °C (+14 to 122 °F) without derating
	-10 to +60 °C (+14 to 140 °F) with fan kit▲ and derating of the current	2.2% per °C above 50 °C
	Drive controllers ATV58HD12N4 to D79N4:
	-10 to +40 °C (+14 to 104 °F) without derating
	-10 to +50 °C (+14 to 122 °F) with fan kit▲ and derating of the current	2.2% per °C above 40 °C
Altitude	3300 ft (1000 m) maximum without derating; derate the output current by 1% for each additional 330 ft (100 m)
Operational position	Vertical, ±10°, with power terminals at the bottom.
◆ See page 33.
▲ See page 33.

NOTE: Discoloration of drive controller plastic pieces will occur if exposed to direct sunlight.

Electrical Specifications

Input voltage	400 V -15% to 460 V + 20% three phase input
Input frequency	50/60 Hz ±5%
Output voltage	Three-phase output, maximum voltage equal to input voltage
Galvanic isolation	Galvanic isolation between power and control (inputs, outputs, supplies)
Output frequency	0 to 60 Hz (configurable to 450 Hz with programming options)◆
Switching frequency	4 kHz, configurable with programming options◆
	ATV58HU18N4–D23N4:
	0.5 - 1 - 2 - 4 - 8 kHz without derating
	12 - 16 kHz with derating in steady state
	12 - 16 kHz without derating and with reduced duty cycle ▲
	ATV58HD28N4–D46N4:
	0.5 - 1 - 2 - 4 kHz without derating
	8 - 12 kHz with derating in steady state
	8 - 12 kHz without derating and with reduced duty cycle▲
	ATV58HD54N4–D79N4:
	0.5 - 1 - 2 kHz without derating
	4 - 8 kHz with derating in steady state
	4 - 8 kHz without derating and with reduced duty cycle▲
Speed range	1:100 Open loop. 1:1000 Closed loop.
Speed regulation	1% of rated motor speed without adjustments or feedback.
	±0.01% of rated motor speed with appropriate encoder feedback.
Efficiency	97% at full load typical.
Displacement power	98% through speed range.
factor
Motor control algorithm	Sensorless flux vector control with a pulse width modulated (PWM) output wave form.
Braking torque	30% of nominal motor torque without dynamic braking (typical value). Up to 150% with dynamic braking option.
Transient output current	160% of nominal NEC rated motor current for 60 seconds (for constant torque ratings).
	110% of nominal motor current for 60 seconds (for variable torque ratings).
Transient motor torque	200% of nominal motor torque (typical value at ±10%) for 2 seconds.
	170% of nominal motor torque (typical value at ±10%) for 60 seconds.

◆Accessories are described starting on page 26.

▲The drive controller can be configured to reduce switching frequency if the drive thermal state reaches 95%. When the drive thermal state returns to 70%, the switching frequency returns to the set value. If the duty cycle (drive controller run time) does not exceed 60% (36 second maximum for a 60 second cycle) derating is not required.

118

© 2000–2003 Schneider Electric All Rights Reserved 09/2003