Invalid parameter Plines command | Xerox DocuPrint 96MX manual

	DOCUPRINT 96/DOCUPRINT 96MX LPS ADDITIONAL MESSAGES

	Invalid parameter - PLINES command.
	A PLINES command has an invalid parameter. The report definition
	file may be corrupt.
Action	If the problem persists, call Xerox Customer Service.

	Invalid parameter - WIDTH command.
	A WIDTH command has an invalid parameter. The report definition
	file may be corrupt.
Action	If the problem persists, call Xerox Customer Service.

	Invalid path or filename to audit files.
	The path or filename requested to contain the audit log formatted text
	is incorrect.
Action	If the problem persists, call Xerox Customer Service.

	Invalid record address for Get Direct.
	TBD
Action	If the problem persists, call Xerox Customer Service.

	Invalid report field name.
	Dialog has requested a field name for the Audit Log list that is not
	supported.
Action	If the problem persists, call Xerox Customer Service.

	Invalid response for BTEXT DAR default reporting parameter.
	The default reporting parameter is incorrectly specified.
Action	Check JSL or DJDE in the job stream to ensure that all BTEXT DAR
	keywords and parameters are correct.

	Invalid response for BTEXT DDE duplicates check enablement
	parameter.
	The duplicates check enablement parameter is incorrectly specified.
Action	Check JSL or DJDE in the job stream to ensure that all BTEXT DDE
	keywords and parameters are correct.

	Invalid response for BTEXT LDT stale date parameter.
	The stale date parameter is incorrectly specified.
Action	Check JSL or DJDE in the job stream to ensure that all BTEXT LDT
	keywords and parameters are correct.

XEROX DOCUPRINT 96/DOCUPRINT 96MX LPS MESSAGE GUIDE

15-45

Page 315

Image 315

Xerox DocuPrint 96MX manual Invalid parameter Plines command, Invalid parameter Width command, Invalid report field name

Contents

April 1998 721P85650 Page Related Publications Number Related publications Xerox Docuprint 96/DOCUPRINT 96MX LPS Message Guide Table of Contents DocuPrint 96/DocuPrint 96MX LPS additional messages System verification error messagesSummary sheet error messages Xerox support services Introduction About the reference setXerox DocuPrint 96/DocuPrint 96MX LPS Operator Guide LPS Operations Reference Xerox DocuPrint 96/DocuPrint 96MX LPS PDL ReferenceXerox DocuPrint 96/DocuPrint 96MX LPS System Generation Guide User Guide What the message guide contains How the message guide is organized Conventions used in this guide CP1900 Insufficient working memory for compress CP Compress command messagesCP1010 Compress now restoring the print file CP1800 Compress processor aborting CP2700 Invalid keyin CP2720 Invalid start commandCP7010 Unable to compress this disk. Use DSR Compress Mode CP9100 File integrity error. Edit and print CPR000.TMP DS2010 Mount and ready DSR tape DSR disk save and restore command messagesDS2020 Mount and ready DSR volume nnnn DS3020 DSR Version 2.0 unable to run on this configuration DS9030 File structure integrity error...DSR aborted DS8010 Tape error xxxx...DSR abortedDS8040 6250 not supported, defaulting to DS9010 Disk error xxxx...DSR aborted DS9040 System error...DSR aborted DS9050 File structure integrity error on xx...DSR abortedDS9060 Invalid DSR.SAF detected Page FD forms compilation messages FD2740 FSL not found or invalid option, check and retry FD4500 Error in reading magnetic tapeFD2720 Key-in too long. Reenter FD2730 Parameter too long. Reenter FD Forms Compilation Messages Page HIP host interface processor messages HP0130 Log file reset HP0085 Concatenated job operator display mode is ‘OFF’HP0090 Job concatenation mode is ‘ON’ HP0095 Job concatenation mode is ‘OFF’ HP1030 Output starting report jid HP0210 Transmission aborted JOB IDHP1010 Input starting report jid HP1020 Input report complete jid HP1150 Cannot start jobs HP1160 Logging already enabledHP1130 Buffer file allocation less than specified HP1140 Cannot abort jobs xxxx , yyyy, etc HP1181 Echo test started. Results available in nnn seconds HP1183 Invalid echo server specificationHP1172 Log file empty, nothing to print HP1180 No echo servers on list HP1230 Host offline HP1207 Offline pending end of current active xns sessionHP1210 Host online. Accepting all jobs HP1220 Host online. Accepting print jobs only HP1260 Interface busy cannot send files HP1280 HIP reset not allowed. Invalid task stateHP1298 XPS communications recovered HP1250 Transmission complete job id HP1300 Assuming negative confirmation HP1299 Xpaf communications recoveredHP1325 Command not permitted by current host HP1410 End of HIP diagnostic HP2030 ALL not allowed at current logon level HP1420 End of test 3 analysisHP2010 No host selected HP2020 Selected host not present on system HP2140 Unable to process jobs list at this time-try again HP2120 Insufficient disk space for host bufferingHP2121 Insufficient disk space for log print file HP2130 Overwrite file name.type Confirm HP2210 File send not allowed HP2160 Enter ‘HIP show log continue’ for moreHP2165 Insufficient disk space for log files HP2200 Rejected nonprint file transfer HP2330 Invalid command with no host specified HP2300 Command error at part of command in errorHP2310 Reenter command HP2320 Invalid command with current host type HP2345 Cannot change output file already exists HP2346 Command not allowed on system UIHP2420 Defer hip diagnostic until OCS queue idle HP2344 Cannot change job does not exist HP8100 HIP dynamic memory allocation failure reload HP5000 Host restarted. Trying to reestablish communications HP9210 Interface failure failed to go offline HP9410 Data to host transfer error. See host for reasonHP8250 Fatal protocol violation detected HP9200 Interface failure unable to receive data HP9432 Line no. n is shorted HP9420 Host not communicating. See host for reasonHP9430 Host timed out in test 3. See host for reason HP9431 Line no. n is open IFU Interpress font utility messages IF1200 Family %0 %1 %2 already exists in directory IF1100 Font familyIF1102 Adding xxxx point IF1105 Building font file xxxx point size n, orientation y IF1421 Continuation volume IF1410 Start of volumeIF1415 Volume IF1420 on next volume IF1601 Consolidating unreferenced character mapping tables IF1503 Replacing with substitute characterIF1504 Adding as rendered character IF1600 Consolidating IPM files IF2000 Aborting ADD IF1629 Parser errorIF2005 Terminated. Font profile contains syntax errors IF2010 Medium parameter must be a symbol IF2032 Wildcarding not permitted IF2025 Unknown parameter on ADD commandIF2030 Command not recognized IF2040 Move command was stopped by end of volume IF2060 IF2050 Please mount the next volume, numberIF2052 Wrong volume has been mounted IF2053 Wrong volume for this volume set has been mounted IF2090 Interpress font was not found IF2080 Reading IF2201 Please have n formatted floppies available IF2098 Are you sure you want to abort? enter ‘Y’ or ‘N’IF2099 Aborting at this time may corrupt the font structure IF2200 Do you have n floppy disks? IF2212 Wrong floppy has been mounted IF2220 Please enter the next floppy, numberIF2233 Incomplete Interpress font read missing font files IF2245 Font or character size exceeds standard format IF2237 Package %0 issued unknown message number %1IF2236 Response was received unsuccessfully IF2239 Font x already exists on system, renamed to y IF2306 Font profile x cannot be opened IF2304 Font profile name is required in ADD commandIF2318 Nonnumeric resolution parameter IF2250 Medium must be tape or cartridge IF2346 Family xxx not found in family directory IF2342 Operation code must be a symbolIF2336 Map x was not found in IPFNTS.SYS IF2344 Operation code must be read or write IF2422 Character mapping table x was not found IF2412 Point size was not found in Dcfonts statementIF2414 Files parameter was not found in Dcfonts statement IF2420 Label missing on MAP statement IF2440 Mapping table x was not found in IPFNTS.SYS IF2428 Orientation x was not found in easy valuesIF2434 Missing name parameter on fonts statement IF2438 Fset parameter x not found IF2704 Syntax error incomplete list IF2701 Syntax error expecting a comma afterIF2702 Syntax error unexpected comma at end of command IF2703 Syntax error expecting = after parm IF2711 Syntax error invalid hex value IF2708 Syntax error unexpected token x encounteredIF2709 Syntax error literal exceeds x characters IF2710 Syntax error hex value is out of range IF2791 Parser error invalid next char 2 call IF2720 Syntax error in statementIF2730 Semantic error in statement IF2790 Parser error next charcalled with invalid mode IF2854 Invalid mapping parameter on fonts statement IF2859 Invalid resolution parameter on fonts statementIF2852 Invalid Ftype parameter IF2853 Invalid Interpress family name IF2861 Invalid substitution parameter IF2862 Invalid density switchIF2863 Invalid font mask in command IF2860 Invalid sections parameter IF2906 JSL syntax err x unclosed comment IF2903 JSL syntax err x unclosed stringIF2904 JSL syntax err x string exceeding y chars IF2905 JSL syntax err x invalid character IF2913 JSL syntax err x invalid JSL statement y IF2910 JSL syntax err x expecting an equal sign after yIF2911 JSL syntax err x unexpected punctuation y IF2912 JSL syntax err x missing right parenthesis IF2970 Invalid hardvalues parameter IF2950 JSL file x will not openIF2951 JSL statement is too large to be processed IF2960 JSL parse err x unexpected token type y, z IF2975 Contour fonts require RIP option aborting ADD IF4110 FIS master error aborting ADDIF2973 No valid characters were found in character set IF2974 Character x is in the system reserved area IF4112 Unable to create a font file, x aborting ADD IF4111 FIS processing error aborting ADDIF4120 Easy values are invalid. fatal error in Interpress IF4121 Easy values are invalid. fatal error in FIS master IF7101 Font file x will not open IF7104 IPFNTS.SYS open errorIF7000 IF7100 Can‘t find IFUFSN.SYS resysgen and retry ADD IF7108 Temporary file x of decomposed FIS will not open IF7701 Error generating font file x aborting ADDIF7702 Error processing the font profile IF7703 Error processing temporary font profile IF7801 Interpress mapping file package ADD function failed IF7800 Interpress decomposer initialization errorIF7803 Character mapping table package error IF7705 Family name directory will not open IF7905 Gtmu allocation of font request memory failed IF7902 CMT package errorIF7903 FFM ADD command failed on file IF7904 FFM package will not open IF7912 IPM Fclose of file x has failed IF7909 Sample command failed, retryIF7911 IPM error IF7910 IPM FDR routine x has failed IF8101 CMT calling sequence error IF7916 IPM package errorIF7930 Error occurred while reading decomposed FIS file IF7931 Error occurred while accessing the CMT block IF8104 CMT entry table has overflowed by map IF8103 CMT symbol table has overflowed by mapIF8201 Error from IPMopen IF8202 Error from FFMopen IF8207 Error from IPMsetfontmask IF8203 Error from IPFopenIF8204 Error from DLMopen IF8205 Error from IPMsetfamilymask IF8213 Error from Ffmreadcurrent F8210 Error from IPFreadblock entryIF8211 Error from Ipfwriteblock Entry IF8212 Error from Ffmfindnext IF8217 Error from Dlmreadseq IF8214 Error from DlmaddIF8215 Error from Ffmcurrfont REF IF8216 Error from Dlmrewind IF8302 IPM disk family x is too big IF8218 Error from FFMDeleteIF8301 IPM calling sequence error IF8307 Interpress decomposer easy value error IF8404 Font set is larger than FontSetArraysize limit IF8401 FIS font request failed with EMT return codeIF8402 FIS initiation failed with EMT return code IF8403 FIS termination failed with EMT return code IF8410 Tape file buffering has failed IF8501 Fatal error has been detected in font requestIF8502 Character x returned error code y IF8409 Missing font mapping header at file offset? IF9003 IF9000IF9001 IF9002 IF9103 Read error on IPFNTS.SYS IF9099 Device errorIF9101 Read error on IPFNTS.SYS IF9102 Write error on IPFNTS.SYS OS Level 0 Confirmation OSS operating system software messages OS0202 Cluster xx selected ***cluster has no current trays OS0060 Resuming full performanceOS0200 Main tray selected OS0201 Cluster xx selected trays OS0411 Stitch is OFF OS0430 Set command acceptedOS0320 Output tray 2 selected OS0410 Separate is OFF OS0700 Cluster xx now deleted OS0510 Input stoppedOS0610 Spacing forward OS0620 Spacing backward OS0732 Finishing exerciser is starting requested print job OS0800 NVM update in progressOS0730 Finishing exerciser utility Successful Exit OS0731 Updating the IOT‘S memory with test profile info OS0840 Entering Lockout Mode OS0801 NVM update completeOS0830 Attention Light enabled OS0831 Attention Light disabled OS0860 Substituting color for color for this report OS0853 Mode xxx housing, -plexOS0855 After Print Quality Adjustment stop before printing OS0856 Print Quality Adjustment request has been canceled OS0870 Substituting color for all colors for all jobs OS0864 All ink substitutions have been canceledOS0865 Color ink substitution has been canceled OS0863 Substituting current dry ink for this report OS0875 Substituting color for all other inks for this job OS0990 Resetting the systemOS0873 Substituting color for color for this job OS0874 Substituting color for all other inks for all jobs OS Level 1 Information OS1006 Printer is not available Printer is being serviced OS1008 Printer is busy, command ignoredOS1007 Printer is busy OS1014 Output cannot be switched--Selected Tray is full OS1011 Starting diagnostic print jobOS1012 ALUN$ failed command ignored OS1013 Device offline, command ignored OS1030 Job xxxx has completed printing OS1020 Job xxxx has completed input phaseOS1031 Diagnostic print job completed OS1017 Physical device %0 substituted for logical device %1 OS1085 Billing report starting OS1072 Bar OFF, n count satisfied, reader is now enabledOS1073 Data1 = nn, Data2 = nn, Data3 = nn, Data4 = nn OS1080 Start accounting report OS1097 User report ending OS1102 Finishing Exerciser is reconnecting to the IOTOS1103 FEX Error, problem while restoring IOT Memory OS1096 Activity report ending OS1133 FEX Warning, number of pages is greater than OS1131 FEX Problem communicating with the IOT. ExitingOS1135 FEX Error, Form x.x does not exist. Exiting OS1132 NVM Finishing locations OS1136 Sheet rotation ‘0’ = None or ‘1’ = Rotate sheet OS1155 Request rejected, diagnostic job already in progressOS1170 Invalid command while offline OS1175 Command not allowed while **** is active OS1195 Undefined ink color OS1190 Invalid parameter, command ignoredOS1200 Command not allowed while HIP or SDI active OS1225 Automatic recovery initiated OS1255 Accounting disabled OS1235 CLP Commands not allowed while printingOS1240 Status command inoperative OS1250 Accounting enabled OS1265 Printer status request already in progress OS1262 Sysgen paper size out of rangeOS1263 Form paper size out of range OS1264 Barcode sequence mismatch OS1273 Command file resumed OS1270 Command file abortedOS1271 Cannot nest command files. Check and retry OS1272 Command file delaying OS1279 Command file error label not found OS1283 Unexpected Barcode encounteredOS1290 Cluster file full OS1293 Feed Main/Aux not in effect, unable to toggle OS1292 Command ignored Main or Aux Cluster not selectedOS1294 Invalid paper tray selected. Command ignored OS1295 Destination trays not configured for this command OS1300 Number of active forms is nn OS1296 There is no stockset specified at this timeOS1297 There are no current trays in any cluster OS1298 Specified paper tray not present OS1326 Already in lockout mode OS1322 Lead edge screen setting is nnOS1323 Energy saver timeout is nn minutes OS1324 Energy Saver mode is disabled OS1342 Currently not in Lockout Mode OS1334 Printer alarm is n, level = nOS1336 XPS Accounting enabled OS1337 XPS Accounting disabled OS1391 Invalid Scan or Dot value. Retry DAlign OS1381 Diagnostic alignment is x Scan lines and y DotsOS1380 Alignment is nn Scan Lines and nn Dots OS1390 Invalid Scan or Dot value. Retry Align OS1415 Sample of Kanji fonts not allowed OS1417 Interpress master not found check Start commandOS1410 Sample not allowed by JDE OS1412 Cannot sample a secured file OS1460 Cannot space if Reports is specified with Start CMD OS1450 Cannot space reports before Start commandOS1421 Page spacing not allowed for N-1 report OS1430 Block spacing not allowed by JDE OS1535 Formatting WP Exception index OS1510 Page spacing stopped by End-of-ReportOS1520 Block spacing stopped by End-of-File OS1530 Cannot backward space any more pages OS1553 Insufficient file space for status/accounting OS1550 Space or move function stopped by end of dataOS1551 Inappropriate disk file type specified OS1552 File does not exist OS1554 Insufficient file space for accounting OS1557 Creating file x.IMGOS1559 File ‘nn.nn’ Deleted OS1562 Font file not found for file-name.FNT OS1580 Can‘t print Ethernet error page missing fontOS1560 Tape rewind complete OS1561 Font mapping does not exist for file-name.FNT OS1600 Input task not active OS1590 Generating Ethernet errorOS1625 Local density problem rasterization in progress OS1627 Local density problem rasterization complete OS1720 System is already Offline OS1726 This system is not configured for this commandOS1728 Btext command not supported without PC-UI OS1700 Input processing not currently stopped OS1760 Reel-to-reel tape unit selected OS1745 Reset in progress, key-in ignoredOS1730 Clear invalid with display, clear ignored OS1750 Nothing to abort OS1800 Input processing aborting OS1809 Diagnostic print job aborted byOS1780 Online input is receiving data OS1781 Online JDE/JDL Host and device type mismatch OS1822 Cannot write to diagnostic print file. TPJ aborted OS1820 Output processing is aborting current reportOS1821 Cannot get LUN assignment. SDI aborted OS1860 Endjob ignored, no data remains to be printed OS1830 Printing 1 copy of current reportOS1835 Printing all copies of report in sections OS1840 Printing all copies of report so far, ending job now OS1927 This system does not support Ethernet processing OS1930 System not configured for selected processOS1959 Partial set delivered to bin before switch occurred Adjustment OS1962 OS1963 Print quality adjustment is already pendingOS1964 No print quality adjustment is pending OS1965 Print quality adjustment was unsuccessful OS1972 FCG exiting unable to locate OS1970 FEX exiting. Unable to run during a print jobExiting. Unable to run during a print job OS1971 FCG exiting. FCG.Lib not present on the system OS1981 Print quality adjustment has been completed OS1980 Performing print quality adjustment OS1984 FCG exiting. Data value is out of range OS1990 Pre-format form using system default paper sizeOS1982 FCG exiting. Invalid profile encountered OS1983 FCG exiting. Failure to connect to the iot OS Level 2 Routine Maintenance OS2002 Check paper supply in TrayOS2003 Check paper supply in Tray Warming UP--BOTH Paper Trays not SET for Same Size OS2004 Paper trays not set for same size OS2008 OS2010 Mount input tape ‘CONTINUE I’ when readyOS2020 Mount next volume ‘CONTINUE I’ when ready OS2007 Empty sample output tray OS2050 All appropriate trays are empty OS2030 Tape at EOV ‘CONTINUE I’ will rewind tapeOS2042 Check paper supply in Tray OS2043 Check paper supply in Tray OS2055 Establishing communications with IOT OS2056 Finished establishing communications with IOTOS2060 Paper Tray 1 is empty OS2070 Paper Tray 2 is empty OS2080 Paper Tray x is emptyOS2090 Trays 1 or 2 must be used for transparencies OS2210 Bin x full OS2091 No available trays are readyOS2100 Main tray not ready OS2150 Display Y/N? OS2220 Output Tray 2 is full OS2230 Output tray is fullOS2259 No selected bin available for current paper size OS2261 Paper in selected tray too small. Change paper OS2260 Paper in selected tray too large. Change if desired OS2262 Paper in cluster xxxx is too large OS2263 Paper in cluster xxxx is too smallOS2282 Current feed cluster deleted OS2289 OS2288 Value. Change Select command or Con OOS2291 Response timeout cluster display stopped OS2295 Problem with stockset, see display below OS2296 Log printing not allowed until system status=’Idle OS2310 Bin x not readyOS2320 Bin 2 not ready OS2453 Invalid font index number for printable string OS2452 Problem with segment separator save fileOS2510 Color housing not ready OS2400 Printer misfeed detected. Check paper supply OS2560 Please clean the tape drive before next tape mount OS2512 Color housing not presentOS2513 Color housing is needed for this report OS2515 Black housing not ready OS2612 Invalid filetype for ink override file name OS2600 Tape volume out of sequence mount correct volumeOS2610 Improper ink-name list specification OS2611 More than 64 ink-names specified OS2613 Ink parameter required on sample command OS2615 File I/O errorOS2614 File not found OS2675 Abort the Report or Print Job OS2672 Enter PQA Command againOS2673 Enter the SUB INK Command or Abort the Print Job OS2674 Enter the PQA Start Command OS2677 No ink substitutions are in effect OS2681 Print Quality Adjustment is requiredOS2682 Change housing for printing in requested ink OS2676 Ink substitution is not allowed by this job OS2692 Empty output tray OS2683 Change housing for color printing orOS2705 Recovery in progress... keyin not allowed OS2691 Ensure proper stock is loaded for Print Job OS2715 Command ignored, retry later OS2710 Invalid command reenterOS2712 Command not allowed while task is running OS2713 This command is no longer supported. See OS2737 Command not supported in this configuration OS2732 Command not allowed until printer is cycled downOS2733 Command not allowed while IOT is in service mode OS2734 Command not allowed while in lockout mode OS2750 Job not found. Check and retry OS2745 Enter password for documentOS2740 JDE not found. Check and retry OS2741 JDL not found. Check and retry OS2811 Following is a document-generated jobstart message OS2822 Do a reset before retrying operationOS2800 Move or space function complete OS2810 Start-up message from Job Tape follows OS2860 Approaching disk saturation OS2825 Complete Online Jobs. Then vary system offlineOS2830 Enter ‘HIP END’ before starting another job OS2840 Output must be stopped before spacing can be done RETRY, specifying another JDE/JDL OS2875 Disk saturation ended. Input resumingOS2885 Max number of fonts exceeded OS2900 OS2922 Enter the Total number of sets to create OS2910 No accounting file entry for departmentOS2915 Security violation OS2921 Check finishing parameter NVM memory OS2980 Function not available in this Logon class OS2990 Use ‘PROBLEM’ at earliest opportunity OS Level 3 Printer problem OS3002 Paper Tray 1 fault--see message at printerOS3001 Check printer doors and top covers OS3004 If fault continues--enter ‘PROBLEM’ OS3003 Paper Tray 2 fault--see message at printer OS3005 Unusable sheets cleared to sample tray OS3006 Possible extra page in output. See printer messageOS3007 Check output--Dry ink may not be sticking to paper OS3008 Transparencies loaded--print simplex to sample tray Warming UP. Both Paper Trays not SET for Same SIZE. Press OS3010 Printer is warming up OS3013 Paper Tray 4 fault -- see message at printer OS3012 Paper Tray 3 fault -- see message at printer OS3040 Output offset failure. Set will not be offset OS3025 If fault continues enter ‘SEL TRAY’ or ‘ABORT O’ orOS3026 If fault continues, enter ‘STITCH OFF’ OS3050 Stitcher is out of wire OS3700 Suspected page-delivery error. Check output OS3705 Suspected set delivery errorOS3400 Printer jam... see printer message OS3710 Set integrity problem. Partial set ejected OS4100 Printer is in diagnostic mode. Call for service OS Level 4 System or tape problem OS4201 Unable to complete operation. Check drive Is online, ‘CONTINUE I’ when ready* call for serviceOS4310 Irrecoverable tape read error during tape dump OS4200 OS4500 Bad block on input medium. Do one of the following If problem continues, run another jobOS4520 Input attempting recovery...tape not ready OS4650 Input has recovered to page boundary OS4700 System has no tape drive OS4651 Output has recovered to page boundaryOS4800 Power failure waiting for disk OS4810 System power-failure recovery in progress OS4820 Power interruption OS4990 System reliability log data being lost. Use ProblemOS4995 Use problem at earliest opportunity OS6007 Ethernet tape job from this host type not supported OS6006 Invalid Ethernet print procedure messageOS Level 6 Job integrity OS6005 Invalid Ethernet tape preamble format OSS Operating System Software Messages OS6101 Rtext file not found OS6090 Label error Illegal block length Continue or Abort?OS6050 Host requested job abort. Job terminated OS6080 LBLLIB.SYS file not found OS6104 Insufficient memory to process graphics OS6102 Disk read error Rtext fileOS6106 Djde processing error unable to read JDE tables OS6103 Insufficient memory for Rtext OS6193 Graphic data for page exceeds graphic memory OS6190 Graphic file xxxxxxx not foundOS6191 Graphic xxxxxx off page and will not be printed OS6192 Too many graphics for OS6196 Copy sensitive form xxxxxx uses graphics OS6195 Interleaved graphic xxxxxx read but not referenced Abort O- abort current report OS6450 Print file problem due to graphicsPrint 1 print one copy of current report Endjob print all copies of report so far, end OS6550 Data not formatted as specified space to next report OS6551 Problem found in block number nnOS6510 Barcode reader not found OS6520 Cannot read index page data block OS6562 Ink index out of range OS6555 Interpress data extraction errorOS6560 Error encountered during Interpress job OS6561 Interpress error code = nn OS6653 Successive page recovery stopped by end of report OS6650 Input has recovered to next report in jobOS6651 Output has recovered to next report in job OS6652 Output has recovered to next page boundary OS6680 Form paper size too large. Form will not be printed OS6700 Syntax error in DjdeOS6705 Djde error illegal page interleaved graphic callout OS6670 Form paper size too small. Form will not be printed OS6711 Djde processing error JDE not found OS6706 Djde error illegal disk interleaved graphic calloutOS6709 Djde processing error SEF file not found OS6710 Djde processing error stockset file not found OS6720 Otext length exceeds limit...OTEXT ignored OS6712 Djde processing error JDL not found OS6721 Djde processing error invalid loadable PDE OS6722 Djde processing error maximum Forms/Fonts exceededOS6723 Djde processing error Insufficient memory for PDE OS6732 File x error-no card image data received OS6728 Djde processing error Feed stock not in stocksetOS6729 Djde proc. error Feed used but no stockset in effect OS6731 File x processing aborted-data format error OS6733 File x overflow-excess card image data lost OS6734 File processing error-invalid destination file nameOS6735 File processing error-illegal destination file type OS6736 File processing error-no label record OS6737 File processing error-security violation OS6738 No space on disk for fileOS6750 Insufficient dynamic memory for DJDE’s OS6755 Word processing merge job no merge file OS6754 Word processing merge job switch codes missingOS6756 Word processing document file I/O error OS6761 Too many SEF Font mapping errors OS6782 Paper size exceeds printer capability OS6820 Improper palette-name specificationOS6780 Unsupported JDL option may jeopardize job integrity OS6781 Unsupported Djde option encountered. See Oprinfo OS6850 Improper host type for XCS file OS6821 Improper color-name specificationOS6822 Improper catalog-name specification OS6851 Inconsistency between JDL and Start Command OS6908 Ordering has been reversed. Check ordered stock OS6900 Data on page exceeds page size. Check outputOS6905 Data origin off page. Check output OS6906 Graphic origin off page. Check output OS6951 Unable to rasterize local density problem OS6920 Line exceeded page limit. Line truncatedOS6949 Density exceeded, page won‘t be printed. Abort O or OS6960 Invalid font index for Rtext Guaranteed, therefore page will not be printedOS6977 Invalid cluster file detected. Default created OS6952 OS7160 Unable to read stockset file from disk OS7170 Translation file content is improperOS7190 Problem with file===== OS7100 PCC or translate table unreadable OS7300 Account form file not found/accounting can‘t print OS7210 Input cannot recover -not enough dynamic memoryOS7220 Input unable to initiate recovery OS7350 Unrecoverable I/O error in accounting file Action None Restart the jobOS7465 Printer not capable of printing 600 SPI output Not support 600 spi output. The job cannot be printed OS7610 Rtext File overflow OS7620 Cannot recover from Djde processing errorOS7551 Insufficient dynamic memory for PDE Table OS7600 DJDE/Delimiter file overflow OS7920 Graphic memory size exceeded. Report aborted OS7900 Font memory exceeded. Report aborted. Report errorOS7830 Insufficient dynamic memory for Fountainheads OS7910 Job too big for available memory-output OS7950 Unable to open print file... Enter Reset then REA OS7970 Feed stock not in stocksetOS7971 Feed stock specified, but no stockset in effect OS Level 8 Probable severe software error OS8010 Input found nothing to printOS8050 IPD internal initialization failure OS8052 IPD dynamic memory initialization failure OS8051 IPD communication initialization failure OS8200 Invalid Tmcb received from a task OS8100 Requested task already active Reboot the systemOS8251 System mailbox read/write error OS8300 Unable to access next file for sample print OS8500 System reliability log lost OS8410 Byte aligned disk I/O request... input abortingOS8420 Bad LBN on disk I/O... input aborting OS8430I Illegal address space on disk I/O...input aborting OS8560 Drive xxx not useable should be drive yyy OS8650 Input has recovered to next job in queueOS8651 Output has recovered to next job in queue OS8555 Drive xxx not useable wrong disk ID OS8704 Output task does not match IG/Printer type OS8800 Insufficient dynamic memory InputOS8852 Invalid font file header OS8855 Invalid form file header OS8860 Format error. Page will not be printedOS8960 File management initialization failure Reboot OS8970 Cannot open recovery file OS8990 Unable to initiate output task OS8980 Unable to initiate input taskOS8985 Unable to initiate HIP task OS8989 Unable to initiate output task OS9102 Unable to access COREIM.SYS OS Level 9 Probable severe hardware errorOS9050 Unexpected error detected by RIP. Enter OS9101 Unable to access RECTK$SYS OS9200 Hardware error-input drive. Call for service OS9103 Disk error with IPD message file, ETNMSG.SYS OS9300 Set-up error. Page won‘t be printed. Abort O or OS9210 Parity error on input medium OS9325 Imaging device error. Page won‘t be printed. Abort O OS9310 Output disk error. Page won‘t be printed. Abort O or 0S9420 Disk error Input OS9380 Printer failure. Enter ‘PROBLEM’, orOS9400 Fatal disk error Call for service do not Reboot OS9410 Memory parity errors Call for service OS9700 Error detected while going offline OS9551 Unable to recover from disk error. Resetting system OS9900 System cannot go Online OS9800 Hardware error/Disk Input. Call for serviceOS9920 No system log. Call for service OS9950 Memory is too degraded to use. Call for service OS9992 Driver task files not found OS9990 Fatal disk error reading device driversOS9989 Unable to acquire memory for device drivers OS9991 Invalid or destroyed task images OS9997 Unable to find system files OS9994 Unable to find system tasksOS9995 System not operational OS9996 Unable to read executive file OS9999 System can not be operated OS9998 Unable to acquire memory for initialization PD0200 JDL replaced PDL job source library compilation messagesPD0100 Noreplace specified PD0150 Replace specified PD0510 Source file is full PD0250 Replace denied by operatorPD0300 Nothing to print, PDL terminated PD0500 No source file will be created PD4500 Tape read error PD1110 JSL contains unsupported featuresPD1200 Use the IFU Ipfnts Command to compile Ipfnts PD2700 Operator command error, retry PD7400 Insufficient available disk space PD7050 Tape record size errorPD8200 and PD8210 Internal error in PDL PD7200 PDL internal table overflow PD9410 System is unable to access or perform any operation onIndicated file because of a fatal system disk error PD9500 Open error -Print File PD9520 Source output file open error PD9510 PDL restart error opening Save File PG Purge command messages PG1010 Purge processor active PG0217 Purging HIP Spool FilePG0300 Processing the entire disk except the Print File PG0310 Purging the following disks excluding print files PR Hardcopy graphics printing command messages PR2730 Vpos value out of range, check and retry PR2600 Not enough space on disk to hardcopyPR2710 Scale factor invalid, check and retry PR2720 Hpos value out of range, check and retry PR2985 Security violation PR9400 Error during file directory searchPR9500 Error during xcs file creation PR2780 No files found matching maskPage PSC printer subsystem controller command messages PS9012 Fatal ERROR*** Problem with SCSIOS.SYS File PS9001 CSI download error -CSI not loadedPS9010 Fatal ERROR***No header on RIPOS.SYS File PS9011 Fatal ERROR***Problem with RIPOS.SYS File PS9960 Download error SAN nn.nn PS9961 Download error SAN nn.nnPS9962 Operating in degraded mode RIP option not available 10-4 Scale command messages Enter Input file name or Return to exit Error n.n generating Output FileError n.n reading Input File Edim META-Code not supported Font file, xxxx, cannot be scaled extended metrics File, xxxx, can not be scaled unknown errorFile type in output name must be Font file xxxx cannot be scaled byte escapement Form File, xxxx, cannot be scaled TL/DL size Illegal switchFont scaling resulted in size mismatch Font xxxx is not alpha-numeric No input file name specified Restoring previous file, xxxx, due to errorsMore than one white space character not supported No dynamic memory Scaling form Run font through fix on CD/IG Version 2 or higherScaling bitmap Scaling font xxxx to yyyy Scaling TL/DL nn Scaling headerScaling logo Scaling TL number n 11-8 SF1100 Task abort SFS status file services command messagesSF1200 Error in user created form file SF1000 Job completed successfully SFS Status File Services Command Messages SF6030 Column SF4500 Cannot write on tape. Check tape and try againSF6010 Statement ignored SF6020 Column ignored SF6051 Cannot do I/O to file. Abort SF6062 W default value assumed for ‘Length’SF6063 W length of content truncated SF6050 Cannot open file. Abort SF6071 Value for ‘Content’ unspecified SF9500 Irrecoverable disk or conversion errorSF6070 Value for ‘Width’ unspecified or exceeds limit 12-6 System verification error messages Devices not accessible name, nameFCG exiting invalid profile encountered Font memory missing Banks xx, xy, xz FCG starting. VersionFCG exiting failure to connect to the IOT FCG exiting data value out of range No graphics memory Operating in degraded modeUpdates Non-Volatile Memory locations No font memory available 13-4 Summary sheet error messages Appearance error message Document generated error message = errorStringFeature requires RIP option Curved lines Feature requires RIP option diagonal lines Feature requires RIP option graphic figures/linesForm file not found fileTypefileName Unexpected error detected by RIP I/O error code nB Overlapping form copy ranges on oneSystem does not handle graphics Appearance warning messages Inches nn.nnn,nn.nnn cm Master Error page n Operator not implemented operator- nameFont interpressFontName substituted for interpressFontName Graphic image off paper on page n at nn.nnn, nn.nnn Master has the wrong format Master error page n the form, logo, or image specifiedPaper selection error medium n undefined by master Wrong format String off paper on page n at nn.nnn,nn.nnn inches Specified color not implemented Fatal error messages No resources graphics exceed memory configuration Insufficient disk space for image file O/I error code nBMalformed installed font fileTypelocalFontName is an old Font update Parse failure stack underflow Too many errors in documentToo many Unexpected RIP errors encountered Operator requested job abort Xdps interface requested job termination Unexpected error. Code = nUnknown state discovered during attempted Mark Recovery Virtual memory limit exceeded Document generated comment page n = commentString Informational messagesCluster clusterName, Paper stockTypestock Define CLUsters and load papers as follows Document printing terminated due to errors Error sheet only document not printed due to errorsMapped from character nB, set nB Document documentName Message follows the ... Font Problem ... messageXerox EPS Print Service of April-86 Substituting n point rotated n degrees characters Master error messages Form problem form image fileTypelocalImageName not Font problem font interpressFontName unknownFont problem form font fileTypelocalFontName not found Font problem number of data fonts exceeds n on this Invalid type for arguments of operator operatorName Illegal operator ordering Fset must precede FgetInsert file not found fileTypefileName Invalid operator ordering Show precedes first font set Nested rendered characters not supported Blank due to errorsPrinting curtailed due to errors Master not well-formed bad document header Operation Parse Failure invalid parsing after endComposed operator Parse failure Mark not found during COUNT/UNMARK Zero divide attempted Problem with insert file invalid file folder fileTypeParse failure unrecognized operator n Property name not found during Getp operation Master warning messages Master Warning page n Processing nested too deepToo many Page Warnings on this System problem messages Unrecoverable disk error reading master HST file Disk error recording errors all messages lostDisk error with graphic samples vector Recovered from system rollover 14-25 14-26 Operating system messages OSxxxx Fault and * hint messagesDocuPrint 96/DocuPrint 96MX LPS additional messages How the messages are organized General action to take Numbered DocuPrint 96/DocuPrint 96MX LPS messages 547 Second NAK detected 544 Signal expected but not receivedProtocol Error 546 Queue has no entries 552 Can’t post Smcomm message 554 Can’t set Terminal Emulation Mode timer555 Invalid communications id or unsupported mode Clear To Send timeout 565 Receive Line Signal Detect timeout 559 Data Set Ready timeoutFrame error detected 561 Parallel device I/O error Invalid paper status update 567 Parity error while receiving569 Can’t kill Terminal Emulation Mode timer 570 Invalid ESS signal ID 1541 No keyword in configuration data 574 Invalid custom signal data1538 Configuration file cannot be found 1539 Config file read error 1549 Missing file name in config record 1546 Missing directory name in config record1547 Invalid directory type in config record 1548 Invalid index type in config record 1555 Invalid parity must be NONE, ODD, or Even 1559 Missing baud rate from config data1560 Comm parameters specify invalid frame in config file 1554 Invalid comm device must be 1 or 1563 Cannot read UI Dirty File UI cannot run 1567 Windows resource handle for Cursors not installed1561 Cannot create UI Dirty File UI cannot run 1562 Cannot open UI Dirty File UI cannot run 1570 Console log report type not specified 1572 Console log path specified in config file invalid1568 No record types specified for console log report 1569 Console log report type out of range 3548 Unable to allocate memory for file view 3549 Unable to allocate memory for Console Log write buffer3550 Unable to read last Console Log Data record 3566 Missing or invalid data to format 3553 Console Log file wrap failed3554 Console Log data file not open 3564 Invalid client data buffer handle Through These are general messages 3578 Console Log is being formatted for printing3579 Console is being transferred to the ESS Messages 4037 through Processing 4504 Couldn’t start MGD timerThrough Contains object and data variable information for action 9043 Memory unlock failure 9041 Invalid access request code9045 Memory free error 9042 Memory lock failure 9055 Disk I/O error code 9049 Not a maintenance file9050 Dialog Release error 9051 Software version error 9066 Cannot return file status 9060 No data file on re-open error9061 Index file error code 9065 DDB file open error 9539 Can’t unlock memory 9541 Memory re-allocate error9537 Can’t allocate memory 9538 Can’t lock memory Boundary must be selected for 0 reams Accelerated access attempt on file unsuccessfully closedSystem error has caused the log print request to be Attempt to access variable length records from AUD File Mgr AUD File Mgr disk read/write error Attempting completion but no completion phase record existsAttempting to update too many files within a transaction AUD File Mgr disk full error Name AUD File Mgr file close errorAUD File Mgr file create i/o error AUD file Mgr extended file not found AUD File Mgr file owner already set AUD File Mgr file not foundAUD File Mgr file not open AUD File Mgr file table full AUD File Mgr operation not allowed at this time AUD File Mgr lock errorAUD File Mgr pre-image i/o error AUD File Mgr pre-image open error AUD File Mgr Supplemental index damaged AUD File Mgr unrecoverable errorAUD File Mgr update or Delete can’t be done because record Extended Get/Step Audit Log formatting no files selected Audit Log reconciliation errorAudit Log sequence error Audit Log stale date fault Btext signal text invalid response Btext signal unrecognized not PAG or RPTBtext signal Page Detail text invalid Btext signal text invalid Cannot allocate memory for report audit heading record Cannot access memory for report format bufferCannot allocate memory for report phase record Cannot allocate memory for format list Cannot open in-process file for crash recovery Cannot allocate memory for report phase record during crashRecovery Cannot find input phase to match output phase Command sequence error, record number not equal to last +1 Command sequence error, Fgrpheader not 1stCommand sequence error, group not larger than last Command sequence error, number out of range Corrupt report definition file Completed reports not finished transferring from In-ProcessLog Corrupt Master Directory file Empty delete list EOR-Output but no output phase record existsError changing directory Error closing report format output file Error writing AUD File Mgr cache buffer Error extending AUD File Mgr fileError opening report format output file Error writing formatted report to file Failure to create AUD File Mgr Directory Master file Expanded Memory Manager reports error to BtreiveFailed to establish communication with the Printer Failure to create AUD File Mgr Audit Log file Failure to open AUD File Mgr Audit Log file Failure to create DDL window for auditorFailure to initialize Btrieve Failure to insert heading record into in-process audit file FCG Exiting FCG.LIB not present on system FCG Exiting Invalid commandFailure to stop AUD file Mgr FCG Exiting Duplicate Profile Entries FCG Exiting Invalid profile-not enough parameters File cannot be accessedFCG Exiting Invalid Profile-Output or input not specified FCG Exiting Invalid profile-too many parameters Filename has invalid extension File could not be found. Ensure that the file name is validFilename has too many characters Filename has invalid characters Inconsistent key flags between key segments Filter file read / open errorIncompatible mode error while opening AUD File Mgr file Filter limit reached by Extended Get/Next operation Insufficient data buffer reading Master Directory file for In-process record read is not Log HeaderIn-process record read is not Page Detail Copy Invalid audit log data set parameter Invalid command syntax ARxInvalid AUD File Mgr op code Invalid audit log data request parameter Invalid parameter Acumincr command Invalid key type when creating or extending fileInvalid parameter Acumclear command Invalid parameter Acumdecr command Invalid parameter Ftext command Invalid parameter Fposl commandInvalid parameter Fposn command Invalid parameter Ftitle command Invalid response for Btext DDE duplicates check enablement Invalid parameter Plines commandInvalid parameter Width command Invalid response for Btext DAR default reporting parameter IP Header record not read while completing Audit Log Previous Key not found reading in-process file for completion copyKey not found reading in-process file for deletion Key value modified by another application during Get Next Maximum number of report reruns exceeded Displayed/saved. If the problem persists, call for ServiceDisplayed/saved. Use a backup log Master directory device full error No reports for this job No transactions specified when file initializedSaved. Call for Service No Master Directory file found File Mgr buffers PAG Btext signal received before RPT Btext signalPrinter failed to send configuration Number of accelerated files exceeds number of available AUD Sheet delivery signal but no output phase record exists Read error during saveReport definition file read / open error Select Download Controller or enter PSC when you wish Target filename already exists SOR-input received out of sequence already in input phaseOr Print request has been cancelled Specified file does not exist Diskette has insufficient space. The System is unable to Printed/displayed/saved. Call for ServicePrinted/displayed/saved. Use a backup log Printed/displayed/saved Too many audit jobs to list. Try filter UI is reaching its memory limit. Close any windows orMenus that are not being used Too many audit reports to list. Try Jobs or filter Variable length portion of page unreadable by Step Direct Waste Management signal but no output phase record existsWrite error during save Unable to write the File. Try again 15-56 Xerox Customer Support Center Xerox support services Xerox Font Center Xerox Customer Service Support Center Glossary Glossary GLOSSARY-3 Glossary GLOSSARY-5 Glossary GLOSSARY-7 Glossary GLOSSARY-9 Glossary Glossary Glossary Glossary Glossary Glossary Glossary Glossary Glossary Glossary Glossary Glossary Glossary Glossary Glossary Glossary Hpos IpsLaser Ppm Lpi Glossary Glossary

Invalid parameter - PLINES command.

Invalid parameter - WIDTH command.

Invalid path or filename to audit files.

Invalid record address for Get Direct.

Invalid report field name.

Invalid response for BTEXT DAR default reporting parameter.

Invalid response for BTEXT DDE duplicates check enablement

parameter.

Invalid response for BTEXT LDT stale date parameter.

XEROX DOCUPRINT 96/DOCUPRINT 96MX LPS MESSAGE GUIDE