Table of Contents

		Related publications	iii
		Notice	iii

Introduction			vii

		About the reference set	vii

		DocuPrint 96/DocuPrint 96MX Laser Printing System document set	vii

		What the message guide contains	x

		How the message guide is organized	xi

		The conventions used in this guide	xii

1.	CP (COMPRESS command) messages		1-1

2.	DSR (disk save and restore command) messages		2-1

3.	FD (forms compilation) messages		3-1

4.	HIP (host interface processor) messages		4-1

5.	IFU (Interpress font utility) messages		5-1

6.	OSS (operating system software) messages		6-1

		OS Level 0: Confirmation	6-1

		OS Level 1: Information	6-10

		OS Level 2: Routine Maintenance	6-45

		OS Level 3: Printer problem	6-72

		OS Level 4: System or tape problem	6-81

		OS Level 6: Job integrity	6-86

		OS Level 7: System problem	6-109

		OS Level 8: Probable severe software error	6-115

		OS Level 9: Probable severe hardware error	6-123

7.	PDL (job source library compilation) messages		7-1

8.	PG (PURGE command) messages		8-1

9.	PR (HARDCOPY graphics printing command) messages		9-1

10. PSC (printer subsystem controller command) messages			10-1

11.	SCALE command messages		11-1

12.	SFS (status file services command) messages		12-1

XEROX DOCUPRINT 96/DOCUPRINT 96MX LPS MESSAGE GUIDE

Page 5

Image 5

Contents

April 1998 721P85650 Page Related Publications Number Related publications Xerox Docuprint 96/DOCUPRINT 96MX LPS Message Guide Table of Contents Summary sheet error messages System verification error messagesXerox support services DocuPrint 96/DocuPrint 96MX LPS additional messages Xerox DocuPrint 96/DocuPrint 96MX LPS Operator Guide IntroductionAbout the reference set Xerox DocuPrint 96/DocuPrint 96MX Xerox DocuPrint 96/DocuPrint 96MX LPS PDL ReferenceLPS System Generation Guide LPS Operations Reference User Guide What the message guide contains How the message guide is organized Conventions used in this guide CP1010 Compress now restoring the print file CP Compress command messagesCP1800 Compress processor aborting CP1900 Insufficient working memory for compress CP7010 Unable to compress this disk. Use DSR Compress Mode CP2720 Invalid start commandCP9100 File integrity error. Edit and print CPR000.TMP CP2700 Invalid keyin DS2020 Mount and ready DSR volume nnnn DSR disk save and restore command messagesDS3020 DSR Version 2.0 unable to run on this configuration DS2010 Mount and ready DSR tape DS8040 6250 not supported, defaulting to DS8010 Tape error xxxx...DSR abortedDS9010 Disk error xxxx...DSR aborted DS9030 File structure integrity error...DSR aborted DS9060 Invalid DSR.SAF detected DS9040 System error...DSR abortedDS9050 File structure integrity error on xx...DSR aborted Page FD forms compilation messages FD2720 Key-in too long. Reenter FD4500 Error in reading magnetic tapeFD2730 Parameter too long. Reenter FD2740 FSL not found or invalid option, check and retry FD Forms Compilation Messages Page HIP host interface processor messages HP0090 Job concatenation mode is ‘ON’ HP0085 Concatenated job operator display mode is ‘OFF’HP0095 Job concatenation mode is ‘OFF’ HP0130 Log file reset HP1010 Input starting report jid HP0210 Transmission aborted JOB IDHP1020 Input report complete jid HP1030 Output starting report jid HP1130 Buffer file allocation less than specified HP1160 Logging already enabledHP1140 Cannot abort jobs xxxx , yyyy, etc HP1150 Cannot start jobs HP1172 Log file empty, nothing to print HP1183 Invalid echo server specificationHP1180 No echo servers on list HP1181 Echo test started. Results available in nnn seconds HP1210 Host online. Accepting all jobs HP1207 Offline pending end of current active xns sessionHP1220 Host online. Accepting print jobs only HP1230 Host offline HP1298 XPS communications recovered HP1280 HIP reset not allowed. Invalid task stateHP1250 Transmission complete job id HP1260 Interface busy cannot send files HP1325 Command not permitted by current host HP1299 Xpaf communications recoveredHP1410 End of HIP diagnostic HP1300 Assuming negative confirmation HP2010 No host selected HP1420 End of test 3 analysisHP2020 Selected host not present on system HP2030 ALL not allowed at current logon level HP2121 Insufficient disk space for log print file HP2120 Insufficient disk space for host bufferingHP2130 Overwrite file name.type Confirm HP2140 Unable to process jobs list at this time-try again HP2165 Insufficient disk space for log files HP2160 Enter ‘HIP show log continue’ for moreHP2200 Rejected nonprint file transfer HP2210 File send not allowed HP2310 Reenter command HP2300 Command error at part of command in errorHP2320 Invalid command with current host type HP2330 Invalid command with no host specified HP2420 Defer hip diagnostic until OCS queue idle HP2346 Command not allowed on system UIHP2344 Cannot change job does not exist HP2345 Cannot change output file already exists HP8100 HIP dynamic memory allocation failure reload HP5000 Host restarted. Trying to reestablish communications HP8250 Fatal protocol violation detected HP9410 Data to host transfer error. See host for reasonHP9200 Interface failure unable to receive data HP9210 Interface failure failed to go offline HP9430 Host timed out in test 3. See host for reason HP9420 Host not communicating. See host for reasonHP9431 Line no. n is open HP9432 Line no. n is shorted IFU Interpress font utility messages IF1102 Adding xxxx point IF1100 Font familyIF1105 Building font file xxxx point size n, orientation y IF1200 Family %0 %1 %2 already exists in directory IF1415 Volume IF1410 Start of volumeIF1420 on next volume IF1421 Continuation volume IF1504 Adding as rendered character IF1503 Replacing with substitute characterIF1600 Consolidating IPM files IF1601 Consolidating unreferenced character mapping tables IF2005 Terminated. Font profile contains syntax errors IF1629 Parser errorIF2010 Medium parameter must be a symbol IF2000 Aborting ADD IF2030 Command not recognized IF2025 Unknown parameter on ADD commandIF2040 Move command was stopped by end of volume IF2032 Wildcarding not permitted IF2052 Wrong volume has been mounted IF2050 Please mount the next volume, numberIF2053 Wrong volume for this volume set has been mounted IF2060 IF2090 Interpress font was not found IF2080 Reading IF2099 Aborting at this time may corrupt the font structure IF2098 Are you sure you want to abort? enter ‘Y’ or ‘N’IF2200 Do you have n floppy disks? IF2201 Please have n formatted floppies available IF2233 Incomplete Interpress font read missing font files IF2212 Wrong floppy has been mountedIF2220 Please enter the next floppy, number IF2236 Response was received unsuccessfully IF2237 Package %0 issued unknown message number %1IF2239 Font x already exists on system, renamed to y IF2245 Font or character size exceeds standard format IF2318 Nonnumeric resolution parameter IF2304 Font profile name is required in ADD commandIF2250 Medium must be tape or cartridge IF2306 Font profile x cannot be opened IF2336 Map x was not found in IPFNTS.SYS IF2342 Operation code must be a symbolIF2344 Operation code must be read or write IF2346 Family xxx not found in family directory IF2414 Files parameter was not found in Dcfonts statement IF2412 Point size was not found in Dcfonts statementIF2420 Label missing on MAP statement IF2422 Character mapping table x was not found IF2434 Missing name parameter on fonts statement IF2428 Orientation x was not found in easy valuesIF2438 Fset parameter x not found IF2440 Mapping table x was not found in IPFNTS.SYS IF2702 Syntax error unexpected comma at end of command IF2701 Syntax error expecting a comma afterIF2703 Syntax error expecting = after parm IF2704 Syntax error incomplete list IF2709 Syntax error literal exceeds x characters IF2708 Syntax error unexpected token x encounteredIF2710 Syntax error hex value is out of range IF2711 Syntax error invalid hex value IF2730 Semantic error in statement IF2720 Syntax error in statementIF2790 Parser error next charcalled with invalid mode IF2791 Parser error invalid next char 2 call IF2852 Invalid Ftype parameter IF2859 Invalid resolution parameter on fonts statementIF2853 Invalid Interpress family name IF2854 Invalid mapping parameter on fonts statement IF2863 Invalid font mask in command IF2862 Invalid density switchIF2860 Invalid sections parameter IF2861 Invalid substitution parameter IF2904 JSL syntax err x string exceeding y chars IF2903 JSL syntax err x unclosed stringIF2905 JSL syntax err x invalid character IF2906 JSL syntax err x unclosed comment IF2911 JSL syntax err x unexpected punctuation y IF2910 JSL syntax err x expecting an equal sign after yIF2912 JSL syntax err x missing right parenthesis IF2913 JSL syntax err x invalid JSL statement y IF2951 JSL statement is too large to be processed IF2950 JSL file x will not openIF2960 JSL parse err x unexpected token type y, z IF2970 Invalid hardvalues parameter IF2973 No valid characters were found in character set IF4110 FIS master error aborting ADDIF2974 Character x is in the system reserved area IF2975 Contour fonts require RIP option aborting ADD IF4120 Easy values are invalid. fatal error in Interpress IF4111 FIS processing error aborting ADDIF4121 Easy values are invalid. fatal error in FIS master IF4112 Unable to create a font file, x aborting ADD IF7000 IF7104 IPFNTS.SYS open errorIF7100 Can‘t find IFUFSN.SYS resysgen and retry ADD IF7101 Font file x will not open IF7702 Error processing the font profile IF7701 Error generating font file x aborting ADDIF7703 Error processing temporary font profile IF7108 Temporary file x of decomposed FIS will not open IF7803 Character mapping table package error IF7800 Interpress decomposer initialization errorIF7705 Family name directory will not open IF7801 Interpress mapping file package ADD function failed IF7903 FFM ADD command failed on file IF7902 CMT package errorIF7904 FFM package will not open IF7905 Gtmu allocation of font request memory failed IF7911 IPM error IF7909 Sample command failed, retryIF7910 IPM FDR routine x has failed IF7912 IPM Fclose of file x has failed IF7930 Error occurred while reading decomposed FIS file IF7916 IPM package errorIF7931 Error occurred while accessing the CMT block IF8101 CMT calling sequence error IF8201 Error from IPMopen IF8103 CMT symbol table has overflowed by mapIF8202 Error from FFMopen IF8104 CMT entry table has overflowed by map IF8204 Error from DLMopen IF8203 Error from IPFopenIF8205 Error from IPMsetfamilymask IF8207 Error from IPMsetfontmask IF8211 Error from Ipfwriteblock Entry F8210 Error from IPFreadblock entryIF8212 Error from Ffmfindnext IF8213 Error from Ffmreadcurrent IF8215 Error from Ffmcurrfont REF IF8214 Error from DlmaddIF8216 Error from Dlmrewind IF8217 Error from Dlmreadseq IF8301 IPM calling sequence error IF8218 Error from FFMDeleteIF8307 Interpress decomposer easy value error IF8302 IPM disk family x is too big IF8402 FIS initiation failed with EMT return code IF8401 FIS font request failed with EMT return codeIF8403 FIS termination failed with EMT return code IF8404 Font set is larger than FontSetArraysize limit IF8502 Character x returned error code y IF8501 Fatal error has been detected in font requestIF8409 Missing font mapping header at file offset? IF8410 Tape file buffering has failed IF9001 IF9000IF9002 IF9003 IF9101 Read error on IPFNTS.SYS IF9099 Device errorIF9102 Write error on IPFNTS.SYS IF9103 Read error on IPFNTS.SYS OS Level 0 Confirmation OSS operating system software messages OS0200 Main tray selected OS0060 Resuming full performanceOS0201 Cluster xx selected trays OS0202 Cluster xx selected ***cluster has no current trays OS0320 Output tray 2 selected OS0430 Set command acceptedOS0410 Separate is OFF OS0411 Stitch is OFF OS0610 Spacing forward OS0510 Input stoppedOS0620 Spacing backward OS0700 Cluster xx now deleted OS0730 Finishing exerciser utility Successful Exit OS0800 NVM update in progressOS0731 Updating the IOT‘S memory with test profile info OS0732 Finishing exerciser is starting requested print job OS0830 Attention Light enabled OS0801 NVM update completeOS0831 Attention Light disabled OS0840 Entering Lockout Mode OS0855 After Print Quality Adjustment stop before printing OS0853 Mode xxx housing, -plexOS0856 Print Quality Adjustment request has been canceled OS0860 Substituting color for color for this report OS0865 Color ink substitution has been canceled OS0864 All ink substitutions have been canceledOS0863 Substituting current dry ink for this report OS0870 Substituting color for all colors for all jobs OS0873 Substituting color for color for this job OS0990 Resetting the systemOS0874 Substituting color for all other inks for all jobs OS0875 Substituting color for all other inks for this job OS Level 1 Information OS1007 Printer is busy OS1006 Printer is not available Printer is being servicedOS1008 Printer is busy, command ignored OS1012 ALUN$ failed command ignored OS1011 Starting diagnostic print jobOS1013 Device offline, command ignored OS1014 Output cannot be switched--Selected Tray is full OS1031 Diagnostic print job completed OS1020 Job xxxx has completed input phaseOS1017 Physical device %0 substituted for logical device %1 OS1030 Job xxxx has completed printing OS1073 Data1 = nn, Data2 = nn, Data3 = nn, Data4 = nn OS1072 Bar OFF, n count satisfied, reader is now enabledOS1080 Start accounting report OS1085 Billing report starting OS1103 FEX Error, problem while restoring IOT Memory OS1102 Finishing Exerciser is reconnecting to the IOTOS1096 Activity report ending OS1097 User report ending OS1135 FEX Error, Form x.x does not exist. Exiting OS1131 FEX Problem communicating with the IOT. ExitingOS1132 NVM Finishing locations OS1133 FEX Warning, number of pages is greater than OS1170 Invalid command while offline OS1155 Request rejected, diagnostic job already in progressOS1175 Command not allowed while **** is active OS1136 Sheet rotation ‘0’ = None or ‘1’ = Rotate sheet OS1200 Command not allowed while HIP or SDI active OS1190 Invalid parameter, command ignoredOS1225 Automatic recovery initiated OS1195 Undefined ink color OS1240 Status command inoperative OS1235 CLP Commands not allowed while printingOS1250 Accounting enabled OS1255 Accounting disabled OS1263 Form paper size out of range OS1262 Sysgen paper size out of rangeOS1264 Barcode sequence mismatch OS1265 Printer status request already in progress OS1271 Cannot nest command files. Check and retry OS1270 Command file abortedOS1272 Command file delaying OS1273 Command file resumed OS1290 Cluster file full OS1279 Command file error label not foundOS1283 Unexpected Barcode encountered OS1294 Invalid paper tray selected. Command ignored OS1292 Command ignored Main or Aux Cluster not selectedOS1295 Destination trays not configured for this command OS1293 Feed Main/Aux not in effect, unable to toggle OS1297 There are no current trays in any cluster OS1296 There is no stockset specified at this timeOS1298 Specified paper tray not present OS1300 Number of active forms is nn OS1323 Energy saver timeout is nn minutes OS1322 Lead edge screen setting is nnOS1324 Energy Saver mode is disabled OS1326 Already in lockout mode OS1336 XPS Accounting enabled OS1334 Printer alarm is n, level = nOS1337 XPS Accounting disabled OS1342 Currently not in Lockout Mode OS1380 Alignment is nn Scan Lines and nn Dots OS1381 Diagnostic alignment is x Scan lines and y DotsOS1390 Invalid Scan or Dot value. Retry Align OS1391 Invalid Scan or Dot value. Retry DAlign OS1410 Sample not allowed by JDE OS1417 Interpress master not found check Start commandOS1412 Cannot sample a secured file OS1415 Sample of Kanji fonts not allowed OS1421 Page spacing not allowed for N-1 report OS1450 Cannot space reports before Start commandOS1430 Block spacing not allowed by JDE OS1460 Cannot space if Reports is specified with Start CMD OS1520 Block spacing stopped by End-of-File OS1510 Page spacing stopped by End-of-ReportOS1530 Cannot backward space any more pages OS1535 Formatting WP Exception index OS1551 Inappropriate disk file type specified OS1550 Space or move function stopped by end of dataOS1552 File does not exist OS1553 Insufficient file space for status/accounting OS1559 File ‘nn.nn’ Deleted OS1554 Insufficient file space for accountingOS1557 Creating file x.IMG OS1560 Tape rewind complete OS1580 Can‘t print Ethernet error page missing fontOS1561 Font mapping does not exist for file-name.FNT OS1562 Font file not found for file-name.FNT OS1625 Local density problem rasterization in progress OS1590 Generating Ethernet errorOS1627 Local density problem rasterization complete OS1600 Input task not active OS1728 Btext command not supported without PC-UI OS1726 This system is not configured for this commandOS1700 Input processing not currently stopped OS1720 System is already Offline OS1730 Clear invalid with display, clear ignored OS1745 Reset in progress, key-in ignoredOS1750 Nothing to abort OS1760 Reel-to-reel tape unit selected OS1780 Online input is receiving data OS1809 Diagnostic print job aborted byOS1781 Online JDE/JDL Host and device type mismatch OS1800 Input processing aborting OS1821 Cannot get LUN assignment. SDI aborted OS1822 Cannot write to diagnostic print file. TPJ abortedOS1820 Output processing is aborting current report OS1835 Printing all copies of report in sections OS1830 Printing 1 copy of current reportOS1840 Printing all copies of report so far, ending job now OS1860 Endjob ignored, no data remains to be printed OS1959 Partial set delivered to bin before switch occurred OS1930 System not configured for selected processAdjustment OS1927 This system does not support Ethernet processing OS1964 No print quality adjustment is pending OS1963 Print quality adjustment is already pendingOS1965 Print quality adjustment was unsuccessful OS1962 Exiting. Unable to run during a print job OS1970 FEX exiting. Unable to run during a print jobOS1971 FCG exiting. FCG.Lib not present on the system OS1972 FCG exiting unable to locate OS1981 Print quality adjustment has been completed OS1980 Performing print quality adjustment OS1982 FCG exiting. Invalid profile encountered OS1990 Pre-format form using system default paper sizeOS1983 FCG exiting. Failure to connect to the iot OS1984 FCG exiting. Data value is out of range OS2003 Check paper supply in Tray OS Level 2 Routine MaintenanceOS2002 Check paper supply in Tray Warming UP--BOTH Paper Trays not SET for Same Size OS2004 Paper trays not set for same size OS2020 Mount next volume ‘CONTINUE I’ when ready OS2010 Mount input tape ‘CONTINUE I’ when readyOS2007 Empty sample output tray OS2008 OS2042 Check paper supply in Tray OS2030 Tape at EOV ‘CONTINUE I’ will rewind tapeOS2043 Check paper supply in Tray OS2050 All appropriate trays are empty OS2060 Paper Tray 1 is empty OS2055 Establishing communications with IOTOS2056 Finished establishing communications with IOT OS2090 Trays 1 or 2 must be used for transparencies OS2070 Paper Tray 2 is emptyOS2080 Paper Tray x is empty OS2100 Main tray not ready OS2091 No available trays are readyOS2150 Display Y/N? OS2210 Bin x full OS2259 No selected bin available for current paper size OS2220 Output Tray 2 is fullOS2230 Output tray is full OS2261 Paper in selected tray too small. Change paper OS2260 Paper in selected tray too large. Change if desired OS2282 Current feed cluster deleted OS2262 Paper in cluster xxxx is too largeOS2263 Paper in cluster xxxx is too small OS2291 Response timeout cluster display stopped OS2288 Value. Change Select command or Con OOS2295 Problem with stockset, see display below OS2289 OS2320 Bin 2 not ready OS2296 Log printing not allowed until system status=’IdleOS2310 Bin x not ready OS2510 Color housing not ready OS2452 Problem with segment separator save fileOS2400 Printer misfeed detected. Check paper supply OS2453 Invalid font index number for printable string OS2513 Color housing is needed for this report OS2512 Color housing not presentOS2515 Black housing not ready OS2560 Please clean the tape drive before next tape mount OS2610 Improper ink-name list specification OS2600 Tape volume out of sequence mount correct volumeOS2611 More than 64 ink-names specified OS2612 Invalid filetype for ink override file name OS2614 File not found OS2613 Ink parameter required on sample commandOS2615 File I/O error OS2673 Enter the SUB INK Command or Abort the Print Job OS2672 Enter PQA Command againOS2674 Enter the PQA Start Command OS2675 Abort the Report or Print Job OS2682 Change housing for printing in requested ink OS2681 Print Quality Adjustment is requiredOS2676 Ink substitution is not allowed by this job OS2677 No ink substitutions are in effect OS2705 Recovery in progress... keyin not allowed OS2683 Change housing for color printing orOS2691 Ensure proper stock is loaded for Print Job OS2692 Empty output tray OS2712 Command not allowed while task is running OS2710 Invalid command reenterOS2713 This command is no longer supported. See OS2715 Command ignored, retry later OS2733 Command not allowed while IOT is in service mode OS2732 Command not allowed until printer is cycled downOS2734 Command not allowed while in lockout mode OS2737 Command not supported in this configuration OS2740 JDE not found. Check and retry OS2745 Enter password for documentOS2741 JDL not found. Check and retry OS2750 Job not found. Check and retry OS2800 Move or space function complete OS2822 Do a reset before retrying operationOS2810 Start-up message from Job Tape follows OS2811 Following is a document-generated jobstart message OS2830 Enter ‘HIP END’ before starting another job OS2825 Complete Online Jobs. Then vary system offlineOS2840 Output must be stopped before spacing can be done OS2860 Approaching disk saturation OS2885 Max number of fonts exceeded OS2875 Disk saturation ended. Input resumingOS2900 RETRY, specifying another JDE/JDL OS2915 Security violation OS2910 No accounting file entry for departmentOS2921 Check finishing parameter NVM memory OS2922 Enter the Total number of sets to create OS2980 Function not available in this Logon class OS2990 Use ‘PROBLEM’ at earliest opportunity OS3001 Check printer doors and top covers OS Level 3 Printer problemOS3002 Paper Tray 1 fault--see message at printer OS3004 If fault continues--enter ‘PROBLEM’ OS3003 Paper Tray 2 fault--see message at printer OS3007 Check output--Dry ink may not be sticking to paper OS3005 Unusable sheets cleared to sample trayOS3006 Possible extra page in output. See printer message OS3008 Transparencies loaded--print simplex to sample tray Warming UP. Both Paper Trays not SET for Same SIZE. Press OS3010 Printer is warming up OS3013 Paper Tray 4 fault -- see message at printer OS3012 Paper Tray 3 fault -- see message at printer OS3026 If fault continues, enter ‘STITCH OFF’ OS3025 If fault continues enter ‘SEL TRAY’ or ‘ABORT O’ orOS3050 Stitcher is out of wire OS3040 Output offset failure. Set will not be offset OS3400 Printer jam... see printer message OS3700 Suspected page-delivery error. Check outputOS3705 Suspected set delivery error OS3710 Set integrity problem. Partial set ejected OS4100 Printer is in diagnostic mode. Call for service OS Level 4 System or tape problem OS4310 Irrecoverable tape read error during tape dump Is online, ‘CONTINUE I’ when ready* call for serviceOS4200 OS4201 Unable to complete operation. Check drive OS4520 Input attempting recovery...tape not ready If problem continues, run another jobOS4650 Input has recovered to page boundary OS4500 Bad block on input medium. Do one of the following OS4800 Power failure waiting for disk OS4651 Output has recovered to page boundaryOS4810 System power-failure recovery in progress OS4700 System has no tape drive OS4995 Use problem at earliest opportunity OS4820 Power interruptionOS4990 System reliability log data being lost. Use Problem OS Level 6 Job integrity OS6006 Invalid Ethernet print procedure messageOS6005 Invalid Ethernet tape preamble format OS6007 Ethernet tape job from this host type not supported OSS Operating System Software Messages OS6050 Host requested job abort. Job terminated OS6090 Label error Illegal block length Continue or Abort?OS6080 LBLLIB.SYS file not found OS6101 Rtext file not found OS6106 Djde processing error unable to read JDE tables OS6102 Disk read error Rtext fileOS6103 Insufficient memory for Rtext OS6104 Insufficient memory to process graphics OS6191 Graphic xxxxxx off page and will not be printed OS6190 Graphic file xxxxxxx not foundOS6192 Too many graphics for OS6193 Graphic data for page exceeds graphic memory OS6196 Copy sensitive form xxxxxx uses graphics OS6195 Interleaved graphic xxxxxx read but not referenced Print 1 print one copy of current report OS6450 Print file problem due to graphicsEndjob print all copies of report so far, end Abort O- abort current report OS6510 Barcode reader not found OS6551 Problem found in block number nnOS6520 Cannot read index page data block OS6550 Data not formatted as specified space to next report OS6560 Error encountered during Interpress job OS6555 Interpress data extraction errorOS6561 Interpress error code = nn OS6562 Ink index out of range OS6651 Output has recovered to next report in job OS6650 Input has recovered to next report in jobOS6652 Output has recovered to next page boundary OS6653 Successive page recovery stopped by end of report OS6705 Djde error illegal page interleaved graphic callout OS6700 Syntax error in DjdeOS6670 Form paper size too small. Form will not be printed OS6680 Form paper size too large. Form will not be printed OS6709 Djde processing error SEF file not found OS6706 Djde error illegal disk interleaved graphic calloutOS6710 Djde processing error stockset file not found OS6711 Djde processing error JDE not found OS6720 Otext length exceeds limit...OTEXT ignored OS6712 Djde processing error JDL not found OS6723 Djde processing error Insufficient memory for PDE OS6721 Djde processing error invalid loadable PDEOS6722 Djde processing error maximum Forms/Fonts exceeded OS6729 Djde proc. error Feed used but no stockset in effect OS6728 Djde processing error Feed stock not in stocksetOS6731 File x processing aborted-data format error OS6732 File x error-no card image data received OS6735 File processing error-illegal destination file type OS6734 File processing error-invalid destination file nameOS6736 File processing error-no label record OS6733 File x overflow-excess card image data lost OS6750 Insufficient dynamic memory for DJDE’s OS6737 File processing error-security violationOS6738 No space on disk for file OS6756 Word processing document file I/O error OS6754 Word processing merge job switch codes missingOS6761 Too many SEF Font mapping errors OS6755 Word processing merge job no merge file OS6780 Unsupported JDL option may jeopardize job integrity OS6820 Improper palette-name specificationOS6781 Unsupported Djde option encountered. See Oprinfo OS6782 Paper size exceeds printer capability OS6822 Improper catalog-name specification OS6821 Improper color-name specificationOS6851 Inconsistency between JDL and Start Command OS6850 Improper host type for XCS file OS6905 Data origin off page. Check output OS6900 Data on page exceeds page size. Check outputOS6906 Graphic origin off page. Check output OS6908 Ordering has been reversed. Check ordered stock OS6949 Density exceeded, page won‘t be printed. Abort O or OS6951 Unable to rasterize local density problemOS6920 Line exceeded page limit. Line truncated OS6977 Invalid cluster file detected. Default created Guaranteed, therefore page will not be printedOS6952 OS6960 Invalid font index for Rtext OS7190 Problem with file===== OS7170 Translation file content is improperOS7100 PCC or translate table unreadable OS7160 Unable to read stockset file from disk OS7220 Input unable to initiate recovery OS7210 Input cannot recover -not enough dynamic memoryOS7350 Unrecoverable I/O error in accounting file OS7300 Account form file not found/accounting can‘t print OS7465 Printer not capable of printing 600 SPI output Restart the jobNot support 600 spi output. The job cannot be printed Action None OS7551 Insufficient dynamic memory for PDE Table OS7620 Cannot recover from Djde processing errorOS7600 DJDE/Delimiter file overflow OS7610 Rtext File overflow OS7830 Insufficient dynamic memory for Fountainheads OS7900 Font memory exceeded. Report aborted. Report errorOS7910 Job too big for available memory-output OS7920 Graphic memory size exceeded. Report aborted OS7971 Feed stock specified, but no stockset in effect OS7950 Unable to open print file... Enter Reset then REAOS7970 Feed stock not in stockset OS8050 IPD internal initialization failure OS Level 8 Probable severe software errorOS8010 Input found nothing to print OS8052 IPD dynamic memory initialization failure OS8051 IPD communication initialization failure OS8251 System mailbox read/write error OS8100 Requested task already active Reboot the systemOS8300 Unable to access next file for sample print OS8200 Invalid Tmcb received from a task OS8420 Bad LBN on disk I/O... input aborting OS8410 Byte aligned disk I/O request... input abortingOS8430I Illegal address space on disk I/O...input aborting OS8500 System reliability log lost OS8651 Output has recovered to next job in queue OS8650 Input has recovered to next job in queueOS8555 Drive xxx not useable wrong disk ID OS8560 Drive xxx not useable should be drive yyy OS8852 Invalid font file header OS8704 Output task does not match IG/Printer typeOS8800 Insufficient dynamic memory Input OS8960 File management initialization failure Reboot OS8860 Format error. Page will not be printedOS8970 Cannot open recovery file OS8855 Invalid form file header OS8985 Unable to initiate HIP task OS8980 Unable to initiate input taskOS8989 Unable to initiate output task OS8990 Unable to initiate output task OS9050 Unexpected error detected by RIP. Enter OS Level 9 Probable severe hardware errorOS9101 Unable to access RECTK$SYS OS9102 Unable to access COREIM.SYS OS9200 Hardware error-input drive. Call for service OS9103 Disk error with IPD message file, ETNMSG.SYS OS9300 Set-up error. Page won‘t be printed. Abort O or OS9210 Parity error on input medium OS9325 Imaging device error. Page won‘t be printed. Abort O OS9310 Output disk error. Page won‘t be printed. Abort O or OS9400 Fatal disk error Call for service do not Reboot OS9380 Printer failure. Enter ‘PROBLEM’, orOS9410 Memory parity errors Call for service 0S9420 Disk error Input OS9700 Error detected while going offline OS9551 Unable to recover from disk error. Resetting system OS9920 No system log. Call for service OS9800 Hardware error/Disk Input. Call for serviceOS9950 Memory is too degraded to use. Call for service OS9900 System cannot go Online OS9989 Unable to acquire memory for device drivers OS9990 Fatal disk error reading device driversOS9991 Invalid or destroyed task images OS9992 Driver task files not found OS9995 System not operational OS9994 Unable to find system tasksOS9996 Unable to read executive file OS9997 Unable to find system files OS9999 System can not be operated OS9998 Unable to acquire memory for initialization PD0100 Noreplace specified PDL job source library compilation messagesPD0150 Replace specified PD0200 JDL replaced PD0300 Nothing to print, PDL terminated PD0250 Replace denied by operatorPD0500 No source file will be created PD0510 Source file is full PD1200 Use the IFU Ipfnts Command to compile Ipfnts PD1110 JSL contains unsupported featuresPD2700 Operator command error, retry PD4500 Tape read error PD8200 and PD8210 Internal error in PDL PD7050 Tape record size errorPD7200 PDL internal table overflow PD7400 Insufficient available disk space Indicated file because of a fatal system disk error System is unable to access or perform any operation onPD9500 Open error -Print File PD9410 PD9520 Source output file open error PD9510 PDL restart error opening Save File PG Purge command messages PG0300 Processing the entire disk except the Print File PG0217 Purging HIP Spool FilePG0310 Purging the following disks excluding print files PG1010 Purge processor active PR Hardcopy graphics printing command messages PR2710 Scale factor invalid, check and retry PR2600 Not enough space on disk to hardcopyPR2720 Hpos value out of range, check and retry PR2730 Vpos value out of range, check and retry PR9500 Error during xcs file creation PR9400 Error during file directory searchPR2780 No files found matching mask PR2985 Security violationPage PSC printer subsystem controller command messages PS9010 Fatal ERROR***No header on RIPOS.SYS File PS9001 CSI download error -CSI not loadedPS9011 Fatal ERROR***Problem with RIPOS.SYS File PS9012 Fatal ERROR*** Problem with SCSIOS.SYS File PS9962 Operating in degraded mode RIP option not available PS9960 Download error SAN nn.nnPS9961 Download error SAN nn.nn 10-4 Scale command messages Error n.n reading Input File Error n.n generating Output FileEdim META-Code not supported Enter Input file name or Return to exit File type in output name must be File, xxxx, can not be scaled unknown errorFont file xxxx cannot be scaled byte escapement Font file, xxxx, cannot be scaled extended metrics Font scaling resulted in size mismatch Illegal switchFont xxxx is not alpha-numeric Form File, xxxx, cannot be scaled TL/DL size More than one white space character not supported Restoring previous file, xxxx, due to errorsNo dynamic memory No input file name specified Scaling bitmap Run font through fix on CD/IG Version 2 or higherScaling font xxxx to yyyy Scaling form Scaling logo Scaling headerScaling TL number n Scaling TL/DL nn 11-8 SF1200 Error in user created form file SFS status file services command messagesSF1000 Job completed successfully SF1100 Task abort SFS Status File Services Command Messages SF6010 Statement ignored SF4500 Cannot write on tape. Check tape and try againSF6020 Column ignored SF6030 Column SF6063 W length of content truncated SF6062 W default value assumed for ‘Length’SF6050 Cannot open file. Abort SF6051 Cannot do I/O to file. Abort SF6070 Value for ‘Width’ unspecified or exceeds limit SF6071 Value for ‘Content’ unspecifiedSF9500 Irrecoverable disk or conversion error 12-6 FCG exiting invalid profile encountered System verification error messagesDevices not accessible name, name FCG exiting failure to connect to the IOT FCG starting. VersionFCG exiting data value out of range Font memory missing Banks xx, xy, xz Updates Non-Volatile Memory locations Operating in degraded modeNo font memory available No graphics memory 13-4 Summary sheet error messages Feature requires RIP option Curved lines Appearance error messageDocument generated error message = errorString Form file not found fileTypefileName Feature requires RIP option diagonal linesFeature requires RIP option graphic figures/lines System does not handle graphics Unexpected error detected by RIP I/O error code nBOverlapping form copy ranges on one Appearance warning messages Font interpressFontName substituted for interpressFontName Master Error page n Operator not implemented operator- nameGraphic image off paper on page n at nn.nnn, nn.nnn Inches nn.nnn,nn.nnn cm Paper selection error medium n undefined by master Master error page n the form, logo, or image specifiedWrong format Master has the wrong format String off paper on page n at nn.nnn,nn.nnn inches Specified color not implemented Fatal error messages Malformed installed font fileTypelocalFontName is an old Insufficient disk space for image file O/I error code nBFont update No resources graphics exceed memory configuration Too many Unexpected RIP errors encountered Too many errors in documentOperator requested job abort Parse failure stack underflow Unknown state discovered during attempted Mark Recovery Unexpected error. Code = nVirtual memory limit exceeded Xdps interface requested job termination Cluster clusterName, Paper stockTypestock Informational messagesDefine CLUsters and load papers as follows Document generated comment page n = commentString Mapped from character nB, set nB Document printing terminated due to errorsError sheet only document not printed due to errors Xerox EPS Print Service of April-86 Message follows the ... Font Problem ... messageSubstituting n point rotated n degrees characters Document documentName Master error messages Font problem form font fileTypelocalFontName not found Font problem font interpressFontName unknownFont problem number of data fonts exceeds n on this Form problem form image fileTypelocalImageName not Insert file not found fileTypefileName Illegal operator ordering Fset must precede FgetInvalid operator ordering Show precedes first font set Invalid type for arguments of operator operatorName Printing curtailed due to errors Blank due to errorsMaster not well-formed bad document header Nested rendered characters not supported Composed operator Parse Failure invalid parsing after endParse failure Mark not found during COUNT/UNMARK Operation Parse failure unrecognized operator n Problem with insert file invalid file folder fileTypeProperty name not found during Getp operation Zero divide attempted Too many Page Warnings on this Master warning messagesMaster Warning page n Processing nested too deep System problem messages Disk error with graphic samples vector Disk error recording errors all messages lostRecovered from system rollover Unrecoverable disk error reading master HST file 14-25 14-26 DocuPrint 96/DocuPrint 96MX LPS additional messages Fault and * hint messagesHow the messages are organized Operating system messages OSxxxx General action to take Numbered DocuPrint 96/DocuPrint 96MX LPS messages Protocol Error 544 Signal expected but not received546 Queue has no entries 547 Second NAK detected 555 Invalid communications id or unsupported mode 554 Can’t set Terminal Emulation Mode timerClear To Send timeout 552 Can’t post Smcomm message Frame error detected 559 Data Set Ready timeout561 Parallel device I/O error 565 Receive Line Signal Detect timeout 569 Can’t kill Terminal Emulation Mode timer 567 Parity error while receiving570 Invalid ESS signal ID Invalid paper status update 1538 Configuration file cannot be found 574 Invalid custom signal data1539 Config file read error 1541 No keyword in configuration data 1547 Invalid directory type in config record 1546 Missing directory name in config record1548 Invalid index type in config record 1549 Missing file name in config record 1560 Comm parameters specify invalid frame in config file 1559 Missing baud rate from config data1554 Invalid comm device must be 1 or 1555 Invalid parity must be NONE, ODD, or Even 1561 Cannot create UI Dirty File UI cannot run 1567 Windows resource handle for Cursors not installed1562 Cannot open UI Dirty File UI cannot run 1563 Cannot read UI Dirty File UI cannot run 1568 No record types specified for console log report 1572 Console log path specified in config file invalid1569 Console log report type out of range 1570 Console log report type not specified 3550 Unable to read last Console Log Data record 3548 Unable to allocate memory for file view3549 Unable to allocate memory for Console Log write buffer 3554 Console Log data file not open 3553 Console Log file wrap failed3564 Invalid client data buffer handle 3566 Missing or invalid data to format 3579 Console is being transferred to the ESS 3578 Console Log is being formatted for printingMessages 4037 through Through These are general messages Through 4504 Couldn’t start MGD timerContains object and data variable information for action Processing 9045 Memory free error 9041 Invalid access request code9042 Memory lock failure 9043 Memory unlock failure 9050 Dialog Release error 9049 Not a maintenance file9051 Software version error 9055 Disk I/O error code 9061 Index file error code 9060 No data file on re-open error9065 DDB file open error 9066 Cannot return file status 9537 Can’t allocate memory 9541 Memory re-allocate error9538 Can’t lock memory 9539 Can’t unlock memory System error has caused the log print request to be Accelerated access attempt on file unsuccessfully closedAttempt to access variable length records from AUD File Mgr Boundary must be selected for 0 reams Attempting to update too many files within a transaction Attempting completion but no completion phase record existsAUD File Mgr disk full error AUD File Mgr disk read/write error AUD File Mgr file create i/o error AUD File Mgr file close errorAUD file Mgr extended file not found Name AUD File Mgr file not open AUD File Mgr file not foundAUD File Mgr file table full AUD File Mgr file owner already set AUD File Mgr pre-image i/o error AUD File Mgr lock errorAUD File Mgr pre-image open error AUD File Mgr operation not allowed at this time AUD File Mgr update or Delete can’t be done because record AUD File Mgr unrecoverable errorExtended Get/Step AUD File Mgr Supplemental index damaged Audit Log sequence error Audit Log reconciliation errorAudit Log stale date fault Audit Log formatting no files selected Btext signal Page Detail text invalid Btext signal unrecognized not PAG or RPTBtext signal text invalid Btext signal text invalid response Cannot allocate memory for report phase record Cannot access memory for report format bufferCannot allocate memory for format list Cannot allocate memory for report audit heading record Recovery Cannot allocate memory for report phase record during crashCannot find input phase to match output phase Cannot open in-process file for crash recovery Command sequence error, group not larger than last Command sequence error, Fgrpheader not 1stCommand sequence error, number out of range Command sequence error, record number not equal to last +1 Log Completed reports not finished transferring from In-ProcessCorrupt Master Directory file Corrupt report definition file Error changing directory EOR-Output but no output phase record existsError closing report format output file Empty delete list Error opening report format output file Error extending AUD File Mgr fileError writing formatted report to file Error writing AUD File Mgr cache buffer Failed to establish communication with the Printer Expanded Memory Manager reports error to BtreiveFailure to create AUD File Mgr Audit Log file Failure to create AUD File Mgr Directory Master file Failure to initialize Btrieve Failure to create DDL window for auditorFailure to insert heading record into in-process audit file Failure to open AUD File Mgr Audit Log file Failure to stop AUD file Mgr FCG Exiting Invalid commandFCG Exiting Duplicate Profile Entries FCG Exiting FCG.LIB not present on system FCG Exiting Invalid Profile-Output or input not specified File cannot be accessedFCG Exiting Invalid profile-too many parameters FCG Exiting Invalid profile-not enough parameters Filename has too many characters File could not be found. Ensure that the file name is validFilename has invalid characters Filename has invalid extension Incompatible mode error while opening AUD File Mgr file Filter file read / open errorFilter limit reached by Extended Get/Next operation Inconsistent key flags between key segments In-process record read is not Page Detail In-process record read is not Log HeaderCopy Insufficient data buffer reading Master Directory file for Invalid AUD File Mgr op code Invalid command syntax ARxInvalid audit log data request parameter Invalid audit log data set parameter Invalid parameter Acumclear command Invalid key type when creating or extending fileInvalid parameter Acumdecr command Invalid parameter Acumincr command Invalid parameter Fposn command Invalid parameter Fposl commandInvalid parameter Ftitle command Invalid parameter Ftext command Invalid parameter Width command Invalid parameter Plines commandInvalid response for Btext DAR default reporting parameter Invalid response for Btext DDE duplicates check enablement IP Header record not read while completing Audit Log Key not found reading in-process file for deletion Key not found reading in-process file for completion copyKey value modified by another application during Get Next Previous Displayed/saved. Use a backup log Displayed/saved. If the problem persists, call for ServiceMaster directory device full error Maximum number of report reruns exceeded Saved. Call for Service No transactions specified when file initializedNo Master Directory file found No reports for this job Printer failed to send configuration PAG Btext signal received before RPT Btext signalNumber of accelerated files exceeds number of available AUD File Mgr buffers Report definition file read / open error Read error during saveSelect Download Controller or enter PSC when you wish Sheet delivery signal but no output phase record exists Or Print request has been cancelled SOR-input received out of sequence already in input phaseSpecified file does not exist Target filename already exists Printed/displayed/saved. Use a backup log Printed/displayed/saved. Call for ServicePrinted/displayed/saved Diskette has insufficient space. The System is unable to Menus that are not being used UI is reaching its memory limit. Close any windows orToo many audit reports to list. Try Jobs or filter Too many audit jobs to list. Try filter Write error during save Waste Management signal but no output phase record existsUnable to write the File. Try again Variable length portion of page unreadable by Step Direct 15-56 Xerox Customer Support Center Xerox support services Xerox Font Center Xerox Customer Service Support Center Glossary Glossary GLOSSARY-3 Glossary GLOSSARY-5 Glossary GLOSSARY-7 Glossary GLOSSARY-9 Glossary Glossary Glossary Glossary Glossary Glossary Glossary Glossary Glossary Glossary Glossary Glossary Glossary Glossary Glossary Glossary Laser HposIps Ppm Lpi Glossary Glossary

Xerox DocuPrint 96MX manual Table of Contents

Models: DocuPrint 96MX

XEROX DOCUPRINT 96/DOCUPRINT 96MX LPS MESSAGE GUIDE