Xerox DocuPrint 96/DocuPrint 96MX, Card

INTRODUCTION

Xerox DocuPrint 96/DocuPrint 96MX LPS PDL Reference

This reference contains the following information:

•Print Description Language components and processes

•Input processing functions

•Output processing functions

•PDL command summary

•Page formatting guidelines

•Character code assignment tables

•PDL programming information with step-by-step instructions

Xerox DocuPrint 96/DocuPrint 96MX	This reference contains the following information:
LPS System Generation Guide	•	Configuration options
	•	Configuration options
	•	Commands
	• OSS software installation, upgrade, and modification
Xerox DocuPrint 96/DocuPrint 96MX This reference contains the following information:
LPS Operations Reference	• Command syntax for operator and system administrator
	• Command syntax for operator and system administrator
		procedures
	•	LPS defaults
	•	LPS resources
	•	Command summaries
	• Communication and graphics on the LPS
	•	Command files

Xerox DocuPrint 96/DocuPrint 96MX LPS Forms Creation Guide

This reference contains the following information:

•Basic concepts for creating forms

•Coding and compiling for LPS Forms Description Language

•Sample form setup command sets

•Tips for successful forms creation

Xerox DocuPrint 96/DocuPrint 96MX This reference provides a quick reference of commonly-used LPS Operator Command Summary commands.

Card

Xerox DocuPrint 96/DocuPrint 96MX This reference contains the following information:

LPS Message Guide

• OSS and other messages

• Meaning and recovery procedures

viii	XEROX DOCUPRINT 96/DOCUPRINT 96MX LPS MESSAGE GUIDE

Page 8

Image 8

Xerox Xerox DocuPrint 96/DocuPrint 96MX LPS PDL Reference, LPS System Generation Guide, LPS Operations Reference, Card

Contents

April 1998 721P85650 Page Related publications Related Publications Number Xerox Docuprint 96/DOCUPRINT 96MX LPS Message Guide Table of Contents System verification error messages Summary sheet error messagesXerox support services DocuPrint 96/DocuPrint 96MX LPS additional messages Xerox DocuPrint 96/DocuPrint 96MX LPS Operator Guide IntroductionAbout the reference set Xerox DocuPrint 96/DocuPrint 96MX LPS PDL Reference Xerox DocuPrint 96/DocuPrint 96MXLPS System Generation Guide LPS Operations Reference User Guide What the message guide contains How the message guide is organized Conventions used in this guide CP Compress command messages CP1010 Compress now restoring the print fileCP1800 Compress processor aborting CP1900 Insufficient working memory for compress CP2720 Invalid start command CP7010 Unable to compress this disk. Use DSR Compress ModeCP9100 File integrity error. Edit and print CPR000.TMP CP2700 Invalid keyin DSR disk save and restore command messages DS2020 Mount and ready DSR volume nnnnDS3020 DSR Version 2.0 unable to run on this configuration DS2010 Mount and ready DSR tape DS8010 Tape error xxxx...DSR aborted DS8040 6250 not supported, defaulting toDS9010 Disk error xxxx...DSR aborted DS9030 File structure integrity error...DSR aborted DS9060 Invalid DSR.SAF detected DS9040 System error...DSR abortedDS9050 File structure integrity error on xx...DSR aborted Page FD forms compilation messages FD4500 Error in reading magnetic tape FD2720 Key-in too long. ReenterFD2730 Parameter too long. Reenter FD2740 FSL not found or invalid option, check and retry FD Forms Compilation Messages Page HIP host interface processor messages HP0085 Concatenated job operator display mode is ‘OFF’ HP0090 Job concatenation mode is ‘ON’HP0095 Job concatenation mode is ‘OFF’ HP0130 Log file reset HP0210 Transmission aborted JOB ID HP1010 Input starting report jidHP1020 Input report complete jid HP1030 Output starting report jid HP1160 Logging already enabled HP1130 Buffer file allocation less than specifiedHP1140 Cannot abort jobs xxxx , yyyy, etc HP1150 Cannot start jobs HP1183 Invalid echo server specification HP1172 Log file empty, nothing to printHP1180 No echo servers on list HP1181 Echo test started. Results available in nnn seconds HP1207 Offline pending end of current active xns session HP1210 Host online. Accepting all jobsHP1220 Host online. Accepting print jobs only HP1230 Host offline HP1280 HIP reset not allowed. Invalid task state HP1298 XPS communications recoveredHP1250 Transmission complete job id HP1260 Interface busy cannot send files HP1299 Xpaf communications recovered HP1325 Command not permitted by current hostHP1410 End of HIP diagnostic HP1300 Assuming negative confirmation HP1420 End of test 3 analysis HP2010 No host selectedHP2020 Selected host not present on system HP2030 ALL not allowed at current logon level HP2120 Insufficient disk space for host buffering HP2121 Insufficient disk space for log print fileHP2130 Overwrite file name.type Confirm HP2140 Unable to process jobs list at this time-try again HP2160 Enter ‘HIP show log continue’ for more HP2165 Insufficient disk space for log filesHP2200 Rejected nonprint file transfer HP2210 File send not allowed HP2300 Command error at part of command in error HP2310 Reenter commandHP2320 Invalid command with current host type HP2330 Invalid command with no host specified HP2346 Command not allowed on system UI HP2420 Defer hip diagnostic until OCS queue idleHP2344 Cannot change job does not exist HP2345 Cannot change output file already exists HP5000 Host restarted. Trying to reestablish communications HP8100 HIP dynamic memory allocation failure reload HP9410 Data to host transfer error. See host for reason HP8250 Fatal protocol violation detectedHP9200 Interface failure unable to receive data HP9210 Interface failure failed to go offline HP9420 Host not communicating. See host for reason HP9430 Host timed out in test 3. See host for reasonHP9431 Line no. n is open HP9432 Line no. n is shorted IFU Interpress font utility messages IF1100 Font family IF1102 Adding xxxx pointIF1105 Building font file xxxx point size n, orientation y IF1200 Family %0 %1 %2 already exists in directory IF1410 Start of volume IF1415 VolumeIF1420 on next volume IF1421 Continuation volume IF1503 Replacing with substitute character IF1504 Adding as rendered characterIF1600 Consolidating IPM files IF1601 Consolidating unreferenced character mapping tables IF1629 Parser error IF2005 Terminated. Font profile contains syntax errorsIF2010 Medium parameter must be a symbol IF2000 Aborting ADD IF2025 Unknown parameter on ADD command IF2030 Command not recognizedIF2040 Move command was stopped by end of volume IF2032 Wildcarding not permitted IF2050 Please mount the next volume, number IF2052 Wrong volume has been mountedIF2053 Wrong volume for this volume set has been mounted IF2060 IF2080 Reading IF2090 Interpress font was not found IF2098 Are you sure you want to abort? enter ‘Y’ or ‘N’ IF2099 Aborting at this time may corrupt the font structureIF2200 Do you have n floppy disks? IF2201 Please have n formatted floppies available IF2233 Incomplete Interpress font read missing font files IF2212 Wrong floppy has been mountedIF2220 Please enter the next floppy, number IF2237 Package %0 issued unknown message number %1 IF2236 Response was received unsuccessfullyIF2239 Font x already exists on system, renamed to y IF2245 Font or character size exceeds standard format IF2304 Font profile name is required in ADD command IF2318 Nonnumeric resolution parameterIF2250 Medium must be tape or cartridge IF2306 Font profile x cannot be opened IF2342 Operation code must be a symbol IF2336 Map x was not found in IPFNTS.SYSIF2344 Operation code must be read or write IF2346 Family xxx not found in family directory IF2412 Point size was not found in Dcfonts statement IF2414 Files parameter was not found in Dcfonts statementIF2420 Label missing on MAP statement IF2422 Character mapping table x was not found IF2428 Orientation x was not found in easy values IF2434 Missing name parameter on fonts statementIF2438 Fset parameter x not found IF2440 Mapping table x was not found in IPFNTS.SYS IF2701 Syntax error expecting a comma after IF2702 Syntax error unexpected comma at end of commandIF2703 Syntax error expecting = after parm IF2704 Syntax error incomplete list IF2708 Syntax error unexpected token x encountered IF2709 Syntax error literal exceeds x charactersIF2710 Syntax error hex value is out of range IF2711 Syntax error invalid hex value IF2720 Syntax error in statement IF2730 Semantic error in statementIF2790 Parser error next charcalled with invalid mode IF2791 Parser error invalid next char 2 call IF2859 Invalid resolution parameter on fonts statement IF2852 Invalid Ftype parameterIF2853 Invalid Interpress family name IF2854 Invalid mapping parameter on fonts statement IF2862 Invalid density switch IF2863 Invalid font mask in commandIF2860 Invalid sections parameter IF2861 Invalid substitution parameter IF2903 JSL syntax err x unclosed string IF2904 JSL syntax err x string exceeding y charsIF2905 JSL syntax err x invalid character IF2906 JSL syntax err x unclosed comment IF2910 JSL syntax err x expecting an equal sign after y IF2911 JSL syntax err x unexpected punctuation yIF2912 JSL syntax err x missing right parenthesis IF2913 JSL syntax err x invalid JSL statement y IF2950 JSL file x will not open IF2951 JSL statement is too large to be processedIF2960 JSL parse err x unexpected token type y, z IF2970 Invalid hardvalues parameter IF4110 FIS master error aborting ADD IF2973 No valid characters were found in character setIF2974 Character x is in the system reserved area IF2975 Contour fonts require RIP option aborting ADD IF4111 FIS processing error aborting ADD IF4120 Easy values are invalid. fatal error in InterpressIF4121 Easy values are invalid. fatal error in FIS master IF4112 Unable to create a font file, x aborting ADD IF7104 IPFNTS.SYS open error IF7000IF7100 Can‘t find IFUFSN.SYS resysgen and retry ADD IF7101 Font file x will not open IF7701 Error generating font file x aborting ADD IF7702 Error processing the font profileIF7703 Error processing temporary font profile IF7108 Temporary file x of decomposed FIS will not open IF7800 Interpress decomposer initialization error IF7803 Character mapping table package errorIF7705 Family name directory will not open IF7801 Interpress mapping file package ADD function failed IF7902 CMT package error IF7903 FFM ADD command failed on fileIF7904 FFM package will not open IF7905 Gtmu allocation of font request memory failed IF7909 Sample command failed, retry IF7911 IPM errorIF7910 IPM FDR routine x has failed IF7912 IPM Fclose of file x has failed IF7916 IPM package error IF7930 Error occurred while reading decomposed FIS fileIF7931 Error occurred while accessing the CMT block IF8101 CMT calling sequence error IF8103 CMT symbol table has overflowed by map IF8201 Error from IPMopenIF8202 Error from FFMopen IF8104 CMT entry table has overflowed by map IF8203 Error from IPFopen IF8204 Error from DLMopenIF8205 Error from IPMsetfamilymask IF8207 Error from IPMsetfontmask F8210 Error from IPFreadblock entry IF8211 Error from Ipfwriteblock EntryIF8212 Error from Ffmfindnext IF8213 Error from Ffmreadcurrent IF8214 Error from Dlmadd IF8215 Error from Ffmcurrfont REFIF8216 Error from Dlmrewind IF8217 Error from Dlmreadseq IF8218 Error from FFMDelete IF8301 IPM calling sequence errorIF8307 Interpress decomposer easy value error IF8302 IPM disk family x is too big IF8401 FIS font request failed with EMT return code IF8402 FIS initiation failed with EMT return codeIF8403 FIS termination failed with EMT return code IF8404 Font set is larger than FontSetArraysize limit IF8501 Fatal error has been detected in font request IF8502 Character x returned error code yIF8409 Missing font mapping header at file offset? IF8410 Tape file buffering has failed IF9000 IF9001IF9002 IF9003 IF9099 Device error IF9101 Read error on IPFNTS.SYSIF9102 Write error on IPFNTS.SYS IF9103 Read error on IPFNTS.SYS OSS operating system software messages OS Level 0 Confirmation OS0060 Resuming full performance OS0200 Main tray selectedOS0201 Cluster xx selected trays OS0202 Cluster xx selected ***cluster has no current trays OS0430 Set command accepted OS0320 Output tray 2 selectedOS0410 Separate is OFF OS0411 Stitch is OFF OS0510 Input stopped OS0610 Spacing forwardOS0620 Spacing backward OS0700 Cluster xx now deleted OS0800 NVM update in progress OS0730 Finishing exerciser utility Successful ExitOS0731 Updating the IOT‘S memory with test profile info OS0732 Finishing exerciser is starting requested print job OS0801 NVM update complete OS0830 Attention Light enabledOS0831 Attention Light disabled OS0840 Entering Lockout Mode OS0853 Mode xxx housing, -plex OS0855 After Print Quality Adjustment stop before printingOS0856 Print Quality Adjustment request has been canceled OS0860 Substituting color for color for this report OS0864 All ink substitutions have been canceled OS0865 Color ink substitution has been canceledOS0863 Substituting current dry ink for this report OS0870 Substituting color for all colors for all jobs OS0990 Resetting the system OS0873 Substituting color for color for this jobOS0874 Substituting color for all other inks for all jobs OS0875 Substituting color for all other inks for this job OS Level 1 Information OS1007 Printer is busy OS1006 Printer is not available Printer is being servicedOS1008 Printer is busy, command ignored OS1011 Starting diagnostic print job OS1012 ALUN$ failed command ignoredOS1013 Device offline, command ignored OS1014 Output cannot be switched--Selected Tray is full OS1020 Job xxxx has completed input phase OS1031 Diagnostic print job completedOS1017 Physical device %0 substituted for logical device %1 OS1030 Job xxxx has completed printing OS1072 Bar OFF, n count satisfied, reader is now enabled OS1073 Data1 = nn, Data2 = nn, Data3 = nn, Data4 = nnOS1080 Start accounting report OS1085 Billing report starting OS1102 Finishing Exerciser is reconnecting to the IOT OS1103 FEX Error, problem while restoring IOT MemoryOS1096 Activity report ending OS1097 User report ending OS1131 FEX Problem communicating with the IOT. Exiting OS1135 FEX Error, Form x.x does not exist. ExitingOS1132 NVM Finishing locations OS1133 FEX Warning, number of pages is greater than OS1155 Request rejected, diagnostic job already in progress OS1170 Invalid command while offlineOS1175 Command not allowed while **** is active OS1136 Sheet rotation ‘0’ = None or ‘1’ = Rotate sheet OS1190 Invalid parameter, command ignored OS1200 Command not allowed while HIP or SDI activeOS1225 Automatic recovery initiated OS1195 Undefined ink color OS1235 CLP Commands not allowed while printing OS1240 Status command inoperativeOS1250 Accounting enabled OS1255 Accounting disabled OS1262 Sysgen paper size out of range OS1263 Form paper size out of rangeOS1264 Barcode sequence mismatch OS1265 Printer status request already in progress OS1270 Command file aborted OS1271 Cannot nest command files. Check and retryOS1272 Command file delaying OS1273 Command file resumed OS1290 Cluster file full OS1279 Command file error label not foundOS1283 Unexpected Barcode encountered OS1292 Command ignored Main or Aux Cluster not selected OS1294 Invalid paper tray selected. Command ignoredOS1295 Destination trays not configured for this command OS1293 Feed Main/Aux not in effect, unable to toggle OS1296 There is no stockset specified at this time OS1297 There are no current trays in any clusterOS1298 Specified paper tray not present OS1300 Number of active forms is nn OS1322 Lead edge screen setting is nn OS1323 Energy saver timeout is nn minutesOS1324 Energy Saver mode is disabled OS1326 Already in lockout mode OS1334 Printer alarm is n, level = n OS1336 XPS Accounting enabledOS1337 XPS Accounting disabled OS1342 Currently not in Lockout Mode OS1381 Diagnostic alignment is x Scan lines and y Dots OS1380 Alignment is nn Scan Lines and nn DotsOS1390 Invalid Scan or Dot value. Retry Align OS1391 Invalid Scan or Dot value. Retry DAlign OS1417 Interpress master not found check Start command OS1410 Sample not allowed by JDEOS1412 Cannot sample a secured file OS1415 Sample of Kanji fonts not allowed OS1450 Cannot space reports before Start command OS1421 Page spacing not allowed for N-1 reportOS1430 Block spacing not allowed by JDE OS1460 Cannot space if Reports is specified with Start CMD OS1510 Page spacing stopped by End-of-Report OS1520 Block spacing stopped by End-of-FileOS1530 Cannot backward space any more pages OS1535 Formatting WP Exception index OS1550 Space or move function stopped by end of data OS1551 Inappropriate disk file type specifiedOS1552 File does not exist OS1553 Insufficient file space for status/accounting OS1559 File ‘nn.nn’ Deleted OS1554 Insufficient file space for accountingOS1557 Creating file x.IMG OS1580 Can‘t print Ethernet error page missing font OS1560 Tape rewind completeOS1561 Font mapping does not exist for file-name.FNT OS1562 Font file not found for file-name.FNT OS1590 Generating Ethernet error OS1625 Local density problem rasterization in progressOS1627 Local density problem rasterization complete OS1600 Input task not active OS1726 This system is not configured for this command OS1728 Btext command not supported without PC-UIOS1700 Input processing not currently stopped OS1720 System is already Offline OS1745 Reset in progress, key-in ignored OS1730 Clear invalid with display, clear ignoredOS1750 Nothing to abort OS1760 Reel-to-reel tape unit selected OS1809 Diagnostic print job aborted by OS1780 Online input is receiving dataOS1781 Online JDE/JDL Host and device type mismatch OS1800 Input processing aborting OS1821 Cannot get LUN assignment. SDI aborted OS1822 Cannot write to diagnostic print file. TPJ abortedOS1820 Output processing is aborting current report OS1830 Printing 1 copy of current report OS1835 Printing all copies of report in sectionsOS1840 Printing all copies of report so far, ending job now OS1860 Endjob ignored, no data remains to be printed OS1930 System not configured for selected process OS1959 Partial set delivered to bin before switch occurredAdjustment OS1927 This system does not support Ethernet processing OS1963 Print quality adjustment is already pending OS1964 No print quality adjustment is pendingOS1965 Print quality adjustment was unsuccessful OS1962 OS1970 FEX exiting. Unable to run during a print job Exiting. Unable to run during a print jobOS1971 FCG exiting. FCG.Lib not present on the system OS1972 FCG exiting unable to locate OS1980 Performing print quality adjustment OS1981 Print quality adjustment has been completed OS1990 Pre-format form using system default paper size OS1982 FCG exiting. Invalid profile encounteredOS1983 FCG exiting. Failure to connect to the iot OS1984 FCG exiting. Data value is out of range OS2003 Check paper supply in Tray OS Level 2 Routine MaintenanceOS2002 Check paper supply in Tray OS2004 Paper trays not set for same size Warming UP--BOTH Paper Trays not SET for Same Size OS2010 Mount input tape ‘CONTINUE I’ when ready OS2020 Mount next volume ‘CONTINUE I’ when readyOS2007 Empty sample output tray OS2008 OS2030 Tape at EOV ‘CONTINUE I’ will rewind tape OS2042 Check paper supply in TrayOS2043 Check paper supply in Tray OS2050 All appropriate trays are empty OS2060 Paper Tray 1 is empty OS2055 Establishing communications with IOTOS2056 Finished establishing communications with IOT OS2090 Trays 1 or 2 must be used for transparencies OS2070 Paper Tray 2 is emptyOS2080 Paper Tray x is empty OS2091 No available trays are ready OS2100 Main tray not readyOS2150 Display Y/N? OS2210 Bin x full OS2259 No selected bin available for current paper size OS2220 Output Tray 2 is fullOS2230 Output tray is full OS2260 Paper in selected tray too large. Change if desired OS2261 Paper in selected tray too small. Change paper OS2282 Current feed cluster deleted OS2262 Paper in cluster xxxx is too largeOS2263 Paper in cluster xxxx is too small OS2288 Value. Change Select command or Con O OS2291 Response timeout cluster display stoppedOS2295 Problem with stockset, see display below OS2289 OS2320 Bin 2 not ready OS2296 Log printing not allowed until system status=’IdleOS2310 Bin x not ready OS2452 Problem with segment separator save file OS2510 Color housing not readyOS2400 Printer misfeed detected. Check paper supply OS2453 Invalid font index number for printable string OS2512 Color housing not present OS2513 Color housing is needed for this reportOS2515 Black housing not ready OS2560 Please clean the tape drive before next tape mount OS2600 Tape volume out of sequence mount correct volume OS2610 Improper ink-name list specificationOS2611 More than 64 ink-names specified OS2612 Invalid filetype for ink override file name OS2614 File not found OS2613 Ink parameter required on sample commandOS2615 File I/O error OS2672 Enter PQA Command again OS2673 Enter the SUB INK Command or Abort the Print JobOS2674 Enter the PQA Start Command OS2675 Abort the Report or Print Job OS2681 Print Quality Adjustment is required OS2682 Change housing for printing in requested inkOS2676 Ink substitution is not allowed by this job OS2677 No ink substitutions are in effect OS2683 Change housing for color printing or OS2705 Recovery in progress... keyin not allowedOS2691 Ensure proper stock is loaded for Print Job OS2692 Empty output tray OS2710 Invalid command reenter OS2712 Command not allowed while task is runningOS2713 This command is no longer supported. See OS2715 Command ignored, retry later OS2732 Command not allowed until printer is cycled down OS2733 Command not allowed while IOT is in service modeOS2734 Command not allowed while in lockout mode OS2737 Command not supported in this configuration OS2745 Enter password for document OS2740 JDE not found. Check and retryOS2741 JDL not found. Check and retry OS2750 Job not found. Check and retry OS2822 Do a reset before retrying operation OS2800 Move or space function completeOS2810 Start-up message from Job Tape follows OS2811 Following is a document-generated jobstart message OS2825 Complete Online Jobs. Then vary system offline OS2830 Enter ‘HIP END’ before starting another jobOS2840 Output must be stopped before spacing can be done OS2860 Approaching disk saturation OS2875 Disk saturation ended. Input resuming OS2885 Max number of fonts exceededOS2900 RETRY, specifying another JDE/JDL OS2910 No accounting file entry for department OS2915 Security violationOS2921 Check finishing parameter NVM memory OS2922 Enter the Total number of sets to create OS2990 Use ‘PROBLEM’ at earliest opportunity OS2980 Function not available in this Logon class OS3001 Check printer doors and top covers OS Level 3 Printer problemOS3002 Paper Tray 1 fault--see message at printer OS3003 Paper Tray 2 fault--see message at printer OS3004 If fault continues--enter ‘PROBLEM’ OS3007 Check output--Dry ink may not be sticking to paper OS3005 Unusable sheets cleared to sample trayOS3006 Possible extra page in output. See printer message OS3008 Transparencies loaded--print simplex to sample tray OS3010 Printer is warming up Warming UP. Both Paper Trays not SET for Same SIZE. Press OS3012 Paper Tray 3 fault -- see message at printer OS3013 Paper Tray 4 fault -- see message at printer OS3025 If fault continues enter ‘SEL TRAY’ or ‘ABORT O’ or OS3026 If fault continues, enter ‘STITCH OFF’OS3050 Stitcher is out of wire OS3040 Output offset failure. Set will not be offset OS3400 Printer jam... see printer message OS3700 Suspected page-delivery error. Check outputOS3705 Suspected set delivery error OS3710 Set integrity problem. Partial set ejected OS Level 4 System or tape problem OS4100 Printer is in diagnostic mode. Call for service Is online, ‘CONTINUE I’ when ready* call for service OS4310 Irrecoverable tape read error during tape dumpOS4200 OS4201 Unable to complete operation. Check drive If problem continues, run another job OS4520 Input attempting recovery...tape not readyOS4650 Input has recovered to page boundary OS4500 Bad block on input medium. Do one of the following OS4651 Output has recovered to page boundary OS4800 Power failure waiting for diskOS4810 System power-failure recovery in progress OS4700 System has no tape drive OS4995 Use problem at earliest opportunity OS4820 Power interruptionOS4990 System reliability log data being lost. Use Problem OS6006 Invalid Ethernet print procedure message OS Level 6 Job integrityOS6005 Invalid Ethernet tape preamble format OS6007 Ethernet tape job from this host type not supported OSS Operating System Software Messages OS6090 Label error Illegal block length Continue or Abort? OS6050 Host requested job abort. Job terminatedOS6080 LBLLIB.SYS file not found OS6101 Rtext file not found OS6102 Disk read error Rtext file OS6106 Djde processing error unable to read JDE tablesOS6103 Insufficient memory for Rtext OS6104 Insufficient memory to process graphics OS6190 Graphic file xxxxxxx not found OS6191 Graphic xxxxxx off page and will not be printedOS6192 Too many graphics for OS6193 Graphic data for page exceeds graphic memory OS6195 Interleaved graphic xxxxxx read but not referenced OS6196 Copy sensitive form xxxxxx uses graphics OS6450 Print file problem due to graphics Print 1 print one copy of current reportEndjob print all copies of report so far, end Abort O- abort current report OS6551 Problem found in block number nn OS6510 Barcode reader not foundOS6520 Cannot read index page data block OS6550 Data not formatted as specified space to next report OS6555 Interpress data extraction error OS6560 Error encountered during Interpress jobOS6561 Interpress error code = nn OS6562 Ink index out of range OS6650 Input has recovered to next report in job OS6651 Output has recovered to next report in jobOS6652 Output has recovered to next page boundary OS6653 Successive page recovery stopped by end of report OS6700 Syntax error in Djde OS6705 Djde error illegal page interleaved graphic calloutOS6670 Form paper size too small. Form will not be printed OS6680 Form paper size too large. Form will not be printed OS6706 Djde error illegal disk interleaved graphic callout OS6709 Djde processing error SEF file not foundOS6710 Djde processing error stockset file not found OS6711 Djde processing error JDE not found OS6712 Djde processing error JDL not found OS6720 Otext length exceeds limit...OTEXT ignored OS6723 Djde processing error Insufficient memory for PDE OS6721 Djde processing error invalid loadable PDEOS6722 Djde processing error maximum Forms/Fonts exceeded OS6728 Djde processing error Feed stock not in stockset OS6729 Djde proc. error Feed used but no stockset in effectOS6731 File x processing aborted-data format error OS6732 File x error-no card image data received OS6734 File processing error-invalid destination file name OS6735 File processing error-illegal destination file typeOS6736 File processing error-no label record OS6733 File x overflow-excess card image data lost OS6750 Insufficient dynamic memory for DJDE’s OS6737 File processing error-security violationOS6738 No space on disk for file OS6754 Word processing merge job switch codes missing OS6756 Word processing document file I/O errorOS6761 Too many SEF Font mapping errors OS6755 Word processing merge job no merge file OS6820 Improper palette-name specification OS6780 Unsupported JDL option may jeopardize job integrityOS6781 Unsupported Djde option encountered. See Oprinfo OS6782 Paper size exceeds printer capability OS6821 Improper color-name specification OS6822 Improper catalog-name specificationOS6851 Inconsistency between JDL and Start Command OS6850 Improper host type for XCS file OS6900 Data on page exceeds page size. Check output OS6905 Data origin off page. Check outputOS6906 Graphic origin off page. Check output OS6908 Ordering has been reversed. Check ordered stock OS6949 Density exceeded, page won‘t be printed. Abort O or OS6951 Unable to rasterize local density problemOS6920 Line exceeded page limit. Line truncated Guaranteed, therefore page will not be printed OS6977 Invalid cluster file detected. Default createdOS6952 OS6960 Invalid font index for Rtext OS7170 Translation file content is improper OS7190 Problem with file=====OS7100 PCC or translate table unreadable OS7160 Unable to read stockset file from disk OS7210 Input cannot recover -not enough dynamic memory OS7220 Input unable to initiate recoveryOS7350 Unrecoverable I/O error in accounting file OS7300 Account form file not found/accounting can‘t print Restart the job OS7465 Printer not capable of printing 600 SPI outputNot support 600 spi output. The job cannot be printed Action None OS7620 Cannot recover from Djde processing error OS7551 Insufficient dynamic memory for PDE TableOS7600 DJDE/Delimiter file overflow OS7610 Rtext File overflow OS7900 Font memory exceeded. Report aborted. Report error OS7830 Insufficient dynamic memory for FountainheadsOS7910 Job too big for available memory-output OS7920 Graphic memory size exceeded. Report aborted OS7971 Feed stock specified, but no stockset in effect OS7950 Unable to open print file... Enter Reset then REAOS7970 Feed stock not in stockset OS8050 IPD internal initialization failure OS Level 8 Probable severe software errorOS8010 Input found nothing to print OS8051 IPD communication initialization failure OS8052 IPD dynamic memory initialization failure OS8100 Requested task already active Reboot the system OS8251 System mailbox read/write errorOS8300 Unable to access next file for sample print OS8200 Invalid Tmcb received from a task OS8410 Byte aligned disk I/O request... input aborting OS8420 Bad LBN on disk I/O... input abortingOS8430I Illegal address space on disk I/O...input aborting OS8500 System reliability log lost OS8650 Input has recovered to next job in queue OS8651 Output has recovered to next job in queueOS8555 Drive xxx not useable wrong disk ID OS8560 Drive xxx not useable should be drive yyy OS8852 Invalid font file header OS8704 Output task does not match IG/Printer typeOS8800 Insufficient dynamic memory Input OS8860 Format error. Page will not be printed OS8960 File management initialization failure RebootOS8970 Cannot open recovery file OS8855 Invalid form file header OS8980 Unable to initiate input task OS8985 Unable to initiate HIP taskOS8989 Unable to initiate output task OS8990 Unable to initiate output task OS Level 9 Probable severe hardware error OS9050 Unexpected error detected by RIP. EnterOS9101 Unable to access RECTK$SYS OS9102 Unable to access COREIM.SYS OS9103 Disk error with IPD message file, ETNMSG.SYS OS9200 Hardware error-input drive. Call for service OS9210 Parity error on input medium OS9300 Set-up error. Page won‘t be printed. Abort O or OS9310 Output disk error. Page won‘t be printed. Abort O or OS9325 Imaging device error. Page won‘t be printed. Abort O OS9380 Printer failure. Enter ‘PROBLEM’, or OS9400 Fatal disk error Call for service do not RebootOS9410 Memory parity errors Call for service 0S9420 Disk error Input OS9551 Unable to recover from disk error. Resetting system OS9700 Error detected while going offline OS9800 Hardware error/Disk Input. Call for service OS9920 No system log. Call for serviceOS9950 Memory is too degraded to use. Call for service OS9900 System cannot go Online OS9990 Fatal disk error reading device drivers OS9989 Unable to acquire memory for device driversOS9991 Invalid or destroyed task images OS9992 Driver task files not found OS9994 Unable to find system tasks OS9995 System not operationalOS9996 Unable to read executive file OS9997 Unable to find system files OS9998 Unable to acquire memory for initialization OS9999 System can not be operated PDL job source library compilation messages PD0100 Noreplace specifiedPD0150 Replace specified PD0200 JDL replaced PD0250 Replace denied by operator PD0300 Nothing to print, PDL terminatedPD0500 No source file will be created PD0510 Source file is full PD1110 JSL contains unsupported features PD1200 Use the IFU Ipfnts Command to compile IpfntsPD2700 Operator command error, retry PD4500 Tape read error PD7050 Tape record size error PD8200 and PD8210 Internal error in PDLPD7200 PDL internal table overflow PD7400 Insufficient available disk space System is unable to access or perform any operation on Indicated file because of a fatal system disk errorPD9500 Open error -Print File PD9410 PD9510 PDL restart error opening Save File PD9520 Source output file open error PG Purge command messages PG0217 Purging HIP Spool File PG0300 Processing the entire disk except the Print FilePG0310 Purging the following disks excluding print files PG1010 Purge processor active PR Hardcopy graphics printing command messages PR2600 Not enough space on disk to hardcopy PR2710 Scale factor invalid, check and retryPR2720 Hpos value out of range, check and retry PR2730 Vpos value out of range, check and retry PR9400 Error during file directory search PR9500 Error during xcs file creationPR2780 No files found matching mask PR2985 Security violationPage PSC printer subsystem controller command messages PS9001 CSI download error -CSI not loaded PS9010 Fatal ERROR***No header on RIPOS.SYS FilePS9011 Fatal ERROR***Problem with RIPOS.SYS File PS9012 Fatal ERROR*** Problem with SCSIOS.SYS File PS9962 Operating in degraded mode RIP option not available PS9960 Download error SAN nn.nnPS9961 Download error SAN nn.nn 10-4 Scale command messages Error n.n generating Output File Error n.n reading Input FileEdim META-Code not supported Enter Input file name or Return to exit File, xxxx, can not be scaled unknown error File type in output name must beFont file xxxx cannot be scaled byte escapement Font file, xxxx, cannot be scaled extended metrics Illegal switch Font scaling resulted in size mismatchFont xxxx is not alpha-numeric Form File, xxxx, cannot be scaled TL/DL size Restoring previous file, xxxx, due to errors More than one white space character not supportedNo dynamic memory No input file name specified Run font through fix on CD/IG Version 2 or higher Scaling bitmapScaling font xxxx to yyyy Scaling form Scaling header Scaling logoScaling TL number n Scaling TL/DL nn 11-8 SFS status file services command messages SF1200 Error in user created form fileSF1000 Job completed successfully SF1100 Task abort SFS Status File Services Command Messages SF4500 Cannot write on tape. Check tape and try again SF6010 Statement ignoredSF6020 Column ignored SF6030 Column SF6062 W default value assumed for ‘Length’ SF6063 W length of content truncatedSF6050 Cannot open file. Abort SF6051 Cannot do I/O to file. Abort SF6070 Value for ‘Width’ unspecified or exceeds limit SF6071 Value for ‘Content’ unspecifiedSF9500 Irrecoverable disk or conversion error 12-6 FCG exiting invalid profile encountered System verification error messagesDevices not accessible name, name FCG starting. Version FCG exiting failure to connect to the IOTFCG exiting data value out of range Font memory missing Banks xx, xy, xz Operating in degraded mode Updates Non-Volatile Memory locationsNo font memory available No graphics memory 13-4 Summary sheet error messages Feature requires RIP option Curved lines Appearance error messageDocument generated error message = errorString Form file not found fileTypefileName Feature requires RIP option diagonal linesFeature requires RIP option graphic figures/lines System does not handle graphics Unexpected error detected by RIP I/O error code nBOverlapping form copy ranges on one Appearance warning messages Master Error page n Operator not implemented operator- name Font interpressFontName substituted for interpressFontNameGraphic image off paper on page n at nn.nnn, nn.nnn Inches nn.nnn,nn.nnn cm Master error page n the form, logo, or image specified Paper selection error medium n undefined by masterWrong format Master has the wrong format Specified color not implemented String off paper on page n at nn.nnn,nn.nnn inches Fatal error messages Insufficient disk space for image file O/I error code nB Malformed installed font fileTypelocalFontName is an oldFont update No resources graphics exceed memory configuration Too many errors in document Too many Unexpected RIP errors encounteredOperator requested job abort Parse failure stack underflow Unexpected error. Code = n Unknown state discovered during attempted Mark RecoveryVirtual memory limit exceeded Xdps interface requested job termination Informational messages Cluster clusterName, Paper stockTypestockDefine CLUsters and load papers as follows Document generated comment page n = commentString Mapped from character nB, set nB Document printing terminated due to errorsError sheet only document not printed due to errors Message follows the ... Font Problem ... message Xerox EPS Print Service of April-86Substituting n point rotated n degrees characters Document documentName Master error messages Font problem font interpressFontName unknown Font problem form font fileTypelocalFontName not foundFont problem number of data fonts exceeds n on this Form problem form image fileTypelocalImageName not Illegal operator ordering Fset must precede Fget Insert file not found fileTypefileNameInvalid operator ordering Show precedes first font set Invalid type for arguments of operator operatorName Blank due to errors Printing curtailed due to errorsMaster not well-formed bad document header Nested rendered characters not supported Parse Failure invalid parsing after end Composed operatorParse failure Mark not found during COUNT/UNMARK Operation Problem with insert file invalid file folder fileType Parse failure unrecognized operator nProperty name not found during Getp operation Zero divide attempted Too many Page Warnings on this Master warning messagesMaster Warning page n Processing nested too deep System problem messages Disk error recording errors all messages lost Disk error with graphic samples vectorRecovered from system rollover Unrecoverable disk error reading master HST file 14-25 14-26 Fault and * hint messages DocuPrint 96/DocuPrint 96MX LPS additional messagesHow the messages are organized Operating system messages OSxxxx General action to take Numbered DocuPrint 96/DocuPrint 96MX LPS messages 544 Signal expected but not received Protocol Error546 Queue has no entries 547 Second NAK detected 554 Can’t set Terminal Emulation Mode timer 555 Invalid communications id or unsupported modeClear To Send timeout 552 Can’t post Smcomm message 559 Data Set Ready timeout Frame error detected561 Parallel device I/O error 565 Receive Line Signal Detect timeout 567 Parity error while receiving 569 Can’t kill Terminal Emulation Mode timer570 Invalid ESS signal ID Invalid paper status update 574 Invalid custom signal data 1538 Configuration file cannot be found1539 Config file read error 1541 No keyword in configuration data 1546 Missing directory name in config record 1547 Invalid directory type in config record1548 Invalid index type in config record 1549 Missing file name in config record 1559 Missing baud rate from config data 1560 Comm parameters specify invalid frame in config file1554 Invalid comm device must be 1 or 1555 Invalid parity must be NONE, ODD, or Even 1567 Windows resource handle for Cursors not installed 1561 Cannot create UI Dirty File UI cannot run1562 Cannot open UI Dirty File UI cannot run 1563 Cannot read UI Dirty File UI cannot run 1572 Console log path specified in config file invalid 1568 No record types specified for console log report1569 Console log report type out of range 1570 Console log report type not specified 3550 Unable to read last Console Log Data record 3548 Unable to allocate memory for file view3549 Unable to allocate memory for Console Log write buffer 3553 Console Log file wrap failed 3554 Console Log data file not open3564 Invalid client data buffer handle 3566 Missing or invalid data to format 3578 Console Log is being formatted for printing 3579 Console is being transferred to the ESSMessages 4037 through Through These are general messages 4504 Couldn’t start MGD timer ThroughContains object and data variable information for action Processing 9041 Invalid access request code 9045 Memory free error9042 Memory lock failure 9043 Memory unlock failure 9049 Not a maintenance file 9050 Dialog Release error9051 Software version error 9055 Disk I/O error code 9060 No data file on re-open error 9061 Index file error code9065 DDB file open error 9066 Cannot return file status 9541 Memory re-allocate error 9537 Can’t allocate memory9538 Can’t lock memory 9539 Can’t unlock memory Accelerated access attempt on file unsuccessfully closed System error has caused the log print request to beAttempt to access variable length records from AUD File Mgr Boundary must be selected for 0 reams Attempting completion but no completion phase record exists Attempting to update too many files within a transactionAUD File Mgr disk full error AUD File Mgr disk read/write error AUD File Mgr file close error AUD File Mgr file create i/o errorAUD file Mgr extended file not found Name AUD File Mgr file not found AUD File Mgr file not openAUD File Mgr file table full AUD File Mgr file owner already set AUD File Mgr lock error AUD File Mgr pre-image i/o errorAUD File Mgr pre-image open error AUD File Mgr operation not allowed at this time AUD File Mgr unrecoverable error AUD File Mgr update or Delete can’t be done because recordExtended Get/Step AUD File Mgr Supplemental index damaged Audit Log reconciliation error Audit Log sequence errorAudit Log stale date fault Audit Log formatting no files selected Btext signal unrecognized not PAG or RPT Btext signal Page Detail text invalidBtext signal text invalid Btext signal text invalid response Cannot access memory for report format buffer Cannot allocate memory for report phase recordCannot allocate memory for format list Cannot allocate memory for report audit heading record Cannot allocate memory for report phase record during crash RecoveryCannot find input phase to match output phase Cannot open in-process file for crash recovery Command sequence error, Fgrpheader not 1st Command sequence error, group not larger than lastCommand sequence error, number out of range Command sequence error, record number not equal to last +1 Completed reports not finished transferring from In-Process LogCorrupt Master Directory file Corrupt report definition file EOR-Output but no output phase record exists Error changing directoryError closing report format output file Empty delete list Error extending AUD File Mgr file Error opening report format output fileError writing formatted report to file Error writing AUD File Mgr cache buffer Expanded Memory Manager reports error to Btreive Failed to establish communication with the PrinterFailure to create AUD File Mgr Audit Log file Failure to create AUD File Mgr Directory Master file Failure to create DDL window for auditor Failure to initialize BtrieveFailure to insert heading record into in-process audit file Failure to open AUD File Mgr Audit Log file FCG Exiting Invalid command Failure to stop AUD file MgrFCG Exiting Duplicate Profile Entries FCG Exiting FCG.LIB not present on system File cannot be accessed FCG Exiting Invalid Profile-Output or input not specifiedFCG Exiting Invalid profile-too many parameters FCG Exiting Invalid profile-not enough parameters File could not be found. Ensure that the file name is valid Filename has too many charactersFilename has invalid characters Filename has invalid extension Filter file read / open error Incompatible mode error while opening AUD File Mgr fileFilter limit reached by Extended Get/Next operation Inconsistent key flags between key segments In-process record read is not Log Header In-process record read is not Page DetailCopy Insufficient data buffer reading Master Directory file for Invalid command syntax ARx Invalid AUD File Mgr op codeInvalid audit log data request parameter Invalid audit log data set parameter Invalid key type when creating or extending file Invalid parameter Acumclear commandInvalid parameter Acumdecr command Invalid parameter Acumincr command Invalid parameter Fposl command Invalid parameter Fposn commandInvalid parameter Ftitle command Invalid parameter Ftext command Invalid parameter Plines command Invalid parameter Width commandInvalid response for Btext DAR default reporting parameter Invalid response for Btext DDE duplicates check enablement IP Header record not read while completing Audit Log Key not found reading in-process file for completion copy Key not found reading in-process file for deletionKey value modified by another application during Get Next Previous Displayed/saved. If the problem persists, call for Service Displayed/saved. Use a backup logMaster directory device full error Maximum number of report reruns exceeded No transactions specified when file initialized Saved. Call for ServiceNo Master Directory file found No reports for this job PAG Btext signal received before RPT Btext signal Printer failed to send configurationNumber of accelerated files exceeds number of available AUD File Mgr buffers Read error during save Report definition file read / open errorSelect Download Controller or enter PSC when you wish Sheet delivery signal but no output phase record exists SOR-input received out of sequence already in input phase Or Print request has been cancelledSpecified file does not exist Target filename already exists Printed/displayed/saved. Call for Service Printed/displayed/saved. Use a backup logPrinted/displayed/saved Diskette has insufficient space. The System is unable to UI is reaching its memory limit. Close any windows or Menus that are not being usedToo many audit reports to list. Try Jobs or filter Too many audit jobs to list. Try filter Waste Management signal but no output phase record exists Write error during saveUnable to write the File. Try again Variable length portion of page unreadable by Step Direct 15-56 Xerox support services Xerox Customer Support Center Xerox Customer Service Support Center Xerox Font Center Glossary Glossary GLOSSARY-3 Glossary GLOSSARY-5 Glossary GLOSSARY-7 Glossary GLOSSARY-9 Glossary Glossary Glossary Glossary Glossary Glossary Glossary Glossary Glossary Glossary Glossary Glossary Glossary Glossary Glossary Glossary Laser HposIps Lpi Ppm Glossary Glossary

Xerox Xerox DocuPrint 96/DocuPrint 96MX LPS PDL Reference, LPS System Generation Guide, Card

Models: DocuPrint 96MX

Xerox DocuPrint 96/DocuPrint 96MX LPS PDL Reference