Video/Voice Port Configuration, 17-45 | Polycom 2000/4000 specification

Polycom RMX 2000 Administrator’s Guide

Video/Voice Port Configuration

The Video/Voice Port Configuration enables you to configure the RMX Resource Capacity and if in MPM+ System Card Configuration Mode, to select the capacity method.

Flexible Resource Capacity Mode

All resources are initially allocated as CIF video ports as it is a resolution commonly supported by all endpoints.

The administrator can allocate some or all of these resources as Voice resources and let the system allocate the remaining Video resources automatically as participants connect to conferences. The system automatically allocates resources according to the connecting participant’s endpoint type, capabilities and line rate.

If the system runs out of voice ports, voice endpoints cannot connect to available video ports. Conversely, video endpoints cannot connect to available voice ports.

Flexible Resource Capacity mode is available and is the default selection in both MPM and MPM+ System Card Configuration Modes. It is the only allocation method in MPM System Card Configuration Mode.

Fixed Resource Capacity

Fixed Resource Capacity enables the administrator to allocate the number of resources available to each video connection type and Audio Only connections in advance. In Fixed Resource Capacity mode, the system is always in a known state, and when used in conjunction with the Resource Report, it gives the administrator precise control over resource allocation and optimization. For more information, see "Forcing Video Resource Allocation to CIF Resolution” on page 16-50.

Fixed Resource Capacity mode is available only in MPM+ System Card

Configuration Modes.

If all resources allocated to a specific endpoint type are in use and an endpoint of that specific type tries to connect to the RMX, the RMX first attempts to connect the endpoint at the next highest resolution. If not resources are available at that level the RMX begins search for connection resolutions at progressively decreasing resolutions.

Example: In a system that has 10 SD ports allocated and in use:

17-45

Image 527

Polycom 2000/4000 manual Video/Voice Port Configuration, Flexible Resource Capacity Mode, Fixed Resource Capacity, 17-45

Contents

Version 5.0.1 January 2010 DOC2518C Polycom RMX 2000/4000 Administrator’s Guide Patent Pending Regulatory Notices RMX 2000 complies with IDA standards G0916-07 Table of Contents Table of Contents Iii Entry Queues, Ad Hoc Conferences and SIP Factories Address Book Operator Assistance & Participant Move Conference and Participant Monitoring Vii Viii Call Flows 15-1 RMX Manager Application 16-1 RMX Administration and Utilities 17-56 ISDN/PSTN Xii Xiii Ad Hoc Conferencing and External Database Authentication Xiv Connecting to the Alternate Management NetworkProcedure 2 Configure the Modem LPR Setting Value Entry Queue Meeting Rooms Standard Conferencing Conferencing Modes Supported resolutions Supplemental Conferencing Features Click the Conference Profiles button Viewing ProfilesTo list Conference Profiles RMX Management pane, expand the Rarely Used list Button Descriptions Name Profile Toolbar To define a new Profile Defining Profiles Field/Option Description Click the Advanced tab Define the following parameters New Profile Advanced dialog box opens At the End After Last Quits All the participants At the End When Last Participant Remains New Profile Video Quality dialog box opens Click the Video Quality tab People Video Definition Guide, H.239 on Content Video Definition New Profile Video Settings dialog box opens Click the Video Settings tab YES Is set to Flexible Mode Number of Video Participants Auto Layout Default Settings Number Available Video Layouts Video Windows Conference Profiles Select one of the Skin options Field/Option Description Parameter Description Modifying an Existing ProfileTo modify the Profile Properties Conference Profile is deleted Deleting a Conference ProfileTo delete a Conference Profile Video Session Modes Dynamic Continuous Presence CP Mode Continuous Presence CP Conferencing High Definition Video Switching Mode 2CIF/WCIF Video Resolutions in CPCIF 512 x 288 pixels at 50 fps Additional Video Resolutions in MPM+ ModeAdditional Intermediate Video Resolutions 352 x 288 pixels at 50 fps HD1080 Setting the Maximum CP Resolution for ConferencingVideo Display with CIF, SD and HD Video Connections A 1X1 Video Layout CP Conferencing with H.263 4CIF 263 4CIF Guidelines Guidelines High Definition Video Switching To Modify the HD Video Switching Threshold Enabling HD Video SwitchingModifying the HD Video Switching Threshold Bit Rate Creating a High Definition Video Switching Profile Select the High Definition Video Switching check box To Create an HD Enabled Profile Monitoring High Definition Video Switching Conferences 239 Content Transmission Modes Endpoint Capabilities Content Protocol Cascade Links Defining Content Sharing Parameters for a ConferenceEntry Queues 5H.239 Content Options Guidelines for Sending Content to Legacy Endpoints Sending Content to Legacy Endpoints Interoperability with Polycom CMA and DMA Content Display on Legacy Endpoints Enabling the Send Content to Legacy Endpoints Option To modify system flags Legacyepcontentdefaultlayout Layout Flag Value Layout Flag Value Stopping a Content SessionClick OK Flag is updated in the Mcmsparameters list To end the current Content session Enabling the Automatic Switching Lecture ModeEnabling Lecture Mode Selecting the Conference Lecturer Restricting Content Broadcast to LecturerTo enable Lecture Mode for the Conference When enabled, the following rules apply Lecture Mode Monitoring To control the Lecture Mode during an Ongoing Conference Polycom RMX 2000/4000 Administrator’s Guide Closed Captions Guidelines MPM and MPM+ Card Configuration ModesClosed Captions To change the flag value New Flag field enter EnableclosedcaptionEnabling Closed Captions Media Encryption Guidelines Media Encryption Encryption Connection Conference AccessSetting Permitted Conference Participant Entry Queue Access YES To modify the Encryption flag Encryption Flag SettingsMove Guidelines Enabling Encryption at the Participant Level To enable encryption at the conference levelEnabling Encryption in the Profile To enable encryption at the participant level Monitoring the Encryption Status Causes of Packet Loss LPR Lost Packet RecoveryLost Packet Recovery Packet Loss Enabling Lost Packet Recovery Lost Packet Recovery Guidelines Monitoring Lost Packet Recovery Polycom RMX 2000/4000 Administrator’s Guide System Level Telepresence ModeRMX Telepresence Mode Guidelines Room Participant/Endpoint Level Conference Level TPX RPX RPX and TPX Video Layouts Number of Endpoints Layouts 2RPX and TPX Room System connected using RMX 2000/4000 Enabling Telepresence Select the required video layout To configure a participant/endpoint for Telepresence RPX TPX Saving an Ongoing Conference as a TemplateAny conference that is ongoing can be saved as a template To save an ongoing conference as a template To start an ongoing conference from a Template Starting an Ongoing Conference From a Template 3Cascaded Conferences Star Topology Cascading Conferences Star Topology 4Video Layouts in Cascaded Conferences Conference a Conference B To define a Cascade-Enabled Entry Queue Creating the Cascade-enabled Entry QueueCreating the cascade-enabled Entry Queue Creating a cascade-enabled Dial-out link Additional Conferencing Information To define the Dial-out Cascaded Link Creating the Dial-out Cascaded Link For Example 78485#24006#1234 Polycom RMX 2000/4000 Administrator’s Guide To enable cascaded links to connect without a password Enabling Cascaded Conferences without Password Conference B Destination Conference Monitoring Cascaded ConferencesConference a Linked Conference Additional Conferencing Information MIH Cascading allows Cascading Conferences H.239-enabled MIH TopologyMIH Cascading Levels Master and Slave Conferences MIH Cascading Guidelines Conference B Conference C Video Session Mode, Line Rate and Video Settings Level Content Sharing RMX to RMX Cascading Setting up MIH Cascading ConferencesConf Kbps 128 256 384 512 768 1024 1472 1920 Mode Dialing RMX 2000 Level Direction Master RMX Creating a Cascade Enabled Entry QueueDialing RMX 2000 Level Direction Additional Conferencing Information To define the dial-out cascade participant link Creating a Cascade Enabled Dial-out Participant LinkCreating the Cascaded Conferences 17New Participant Dial-out Cascade Link GatekeeperPrefix CascadeEnable Additional Conferencing Information MGC to MGC to RMX 2000 Cascading To MGC Setting the flags in the MGC Defining the Cascading Entry Queue in the MGC Click OK If you changed the flags, reset the MCU For Example 1002##12001##1234 Participant Properties Identification dialog box, enter aParticipant Name For Example FORCE1X1LAYOUTONCASCADEDLINK CONNECTION=YES default Setting the Flags on the RMXH263ANNEXT=YES default For more details, see the RMX 2000 to RMX 2000 Cascading Click OK Reset the MCU to apply the changesDefining the Cascade Enabled Entry Queue on the RMX Defining the Dial-out Participant on the RMX Defining the Cascading Conferences EQ ID MCU Prefix as Password Monitoring Participants in an MIH Cascaded Conference Starting and Monitoring MIH Cascading Conferences To monitor cascading enabled conferences To view the linked Participant Properties Viewing Participant Properties Additional Conferencing Information Meeting Rooms Meeting Room Name Default Line Rate Meeting Rooms List is displayed Meeting Rooms ListTo list Meeting Rooms Meeting Rooms button Meeting Room List columns include Toolbar Right-click Description Button Menu Meeting Room Toolbar & Right-click Menu To create a new meeting room Creating a New Meeting Room Entry Queues Entry Queues, Ad Hoc Conferences and SIP Factories Parameter Value Default Entry Queue properties Polycom RMX 2000/4000 Administrator’s Guide RMX Management Rarely Used pane, click Entry Queues Defining a New Entry QueueTo define a new Entry Queue Option Description Option Description ISDN/PSTN To view the list of Entry Queues Listing Entry QueuesClick OK New Entry Queue is added to the Entry Queues list To modify the EQ Setting a Transit Entry QueueModifying the EQ Properties Transit Entry Queue RMX Management Rarely Used pane click Entry Queues To cancel the Transit Entry Queue setting Ad Hoc Conferencing Gateway to Polycom Distributed Media Application DMA RMX Management Rarely Used pane, click SIP Factories SIP FactoriesCreating SIP Factories To create a new SIP Factory New Factory Properties Click OK New SIP Factory is added to the list Entry Queues, Ad Hoc Conferences and SIP Factories Address Book Displaying and Hiding the Address Book Viewing the Address Book Click the tab to re-open the Address Book To add a new participant to the Address Book Adding a Participant to the Address BookAdding a new participant to the Address Book Directly Ascii Define the following fields Only SIP Address, first select the type of alias and then enter Field Description SIP Only IP Only Define the following Advanced parameters AGC Cascaded Link If this participant is used as a link between Click the Add to Address book button Participant Properties window opens Participant’s Properties window appears When required, you can modify the participant’s propertiesModifying Participants in the Address Book To modify participant properties in the Address Book To search for participants in the Address Book Deleting Participants from the Address BookSearching the Address Book To delete participants from the Address Book To filter an address book field Filtering the Address Book To clear the filter and display all entries To define a New Group Participant GroupsAdding a New Group to the Address Book To delete a Group Deleting a Group from the Address Book To Modify a Group Modifying a Group in the Address Book To Export an Address Book Importing and Exporting Address BooksExporting an Address Book To Import and Address Book Importing an Address Book CMA Address Book Integration Guidelines RMX Side On the RMX menu, click Setup System ConfigurationIntegrating the Polycom CMA Address Book with the RMX External ContentSystem Flags Mcmsparametersuser dialog box opens Flag Description User ContentipPassword External Http//IP address of the CMA server Address Book Resources GuidelinesSystem Reservations Reservations RMX Management pane, click the Reservations button Using the Reservation CalendarTo open the Reservation Calendar Button Description Reservations ViewsToolbar Buttons Toolbar buttons functions are described in Table Single day is displayed Week ViewDay View Today View List View To change between Week and Day views Changing the Calendar View To change to List View To view Today the current date To return to Calendar View Scheduling Conferences Using Reservation CalendarCreating a New Reservation Open the Reservations Method III To interactively define the durationTo create a new reservation 2New Reservation Reserved Resources Click the Schedule tab 3New Reservation Schedule Tab First, second,...,last Sun-Sat Day 1-31 of every 1-12 months Field Description Click the Participants tab If 3 recurrences of the reservation are created ExampleConference Template name Sales Display Name for single scheduled occurrence Sales Viewing and Modifying Reservations Using the Week and Day views of the Reservations CalendarReservations can be accessed and managed via all the views Managing Reservations To change the Reservation’s End time To move the Reservation to another time slotTo change the Reservation’s Start time To delete all recurrences of a reservation Deleting ReservationsTo delete a single reservation Click the Delete Reservation button. or Reservations by Display Name Searching for Reservations using Quick SearchSelect Delete the series Click OK All occurrences of the Reservation are deleted All Reservations are displayed To clear the search and display all reservationsClear the Quick Search field Click Search Operator Conferences Operator Assistance & Participant Move Operator Conference Guidelines Defining the Components Enabling Operator Assistance Click the Conference Chairperson tab New Conference IVR Service Welcome dialog box opens Click the Video Services tab Click the Conference Password tabNew Conference IVR Service General dialog box opens New Conference IVR Service Roll Call dialog box opens Click the Operator Assistance tab New Conference IVR Service Dtmf Codes dialog box opens Polycom RMX 2000/4000 Administrator’s Guide New Entry Queue IVR Service Video Services dialog box opens New Entry Queue IVR Service Welcome dialog box opensNew Entry Queue IVR Service Conference ID dialog box opens Defining a Conference Profile for an Operator Conference 1New Profile General Parameters Line rate and use HD video 2New Profile Advanced Parameters Recording link which is not considered a participant 3New Profile Video Quality Parameters Content Settings To start a conference from the Conference pane Defining an Ongoing Operator Conference 4New Conference General Options Be used in the Routing Name Comma, colon and semicolon characters cannot Field Description New Conference Participants dialog box opens Right-click and select Save Conference to Template Saving an Operator Conference to a TemplateTo save an ongoing Operator conference as a template Right-click and select Start Conference from Template Starting an Operator Conference from a TemplateClick the Start Conference from Template button. or Requesting Help Icon Status indication Description Participant Alerts List Audible AlarmsUsing Audible Alarms Move Guidelines Moving Participants Between Conferences Moving Participants Using drag and drop Moving a Participant Interactively Operator Assistance & Participant Move Conference Template Guidelines Conference Templates Clicking the tab opens the Conference Templates list Using Conference Templates Conferences List toolbar includes the following button Conference Template toolbar includes the following buttons Click the New Conference Template button Creating a New Conference TemplateCreating a new Conference Template from Scratch To create a new Conference Template New Template Participants dialog box opens Modify the fields of the General tab New Participant General tab opens New Participant Advanced tab opens Optional. Click the Information tab New Participant Information tab opens New Conference Template Information tab opens Saving an Ongoing Conference as a Template Polycom RMX 2000/4000 Administrator’s Guide Starting an Ongoing Conference From a Template Starting an Operator Conference from a Template Right-click and select Schedule Reservation from Template Scheduling a Reservation From a Conference TemplateReservation To schedule a Reservation from a Conference Template Conference Template and Reservation Name To delete Conference Templates Deleting a Conference TemplateSeries number 0000n of each reservation is appended to its Display Name Conference and Participant Monitoring General Monitoring To view the parameters of an ongoing conference Conference Level Monitoring Following information appears in the General tab Same line rate and use HD video Conference Properties Advanced dialog box opens Conference Properties Video Quality dialog box opens Following information appears in the Advanced tab Following information appears Click the Video Settings tab to list the video parameters Selecting a lecturer enables the Lecture Mode Requesting Help Icon Status indication Description Participant Alerts List Participant Properties Media Sources dialog box opens Participant Level MonitoringDisplaying Participants Properties IP Participant Properties Field Description Participant Status Capabilities used for the connection   Columns Channels Maximum network jitter since the channel was Field Description Click the Gatekeeper Status tab to view its parameters 11Participant Properties Gatekeeper Status Parameters Algorithm Monitoring ISDN/PSTN ParticipantsBit Rate Audio Participant Properties Media Sources dialog box is displayed To view the participant’s properties during a conference Field Description 14Participant Properties H.221 Parameters Polycom RMX 2000/4000 Administrator’s Guide 15ISDN/PSTN Participant Properties Connection Status 16ISDN/PSTN Participant Properties Channel Status MCU Participant Phone Number In a dial-in 10-1 Configuring the RMX to enable RecordingDefining the Recording Link 10-2 To define a Recording LinkClick OK Recording Link is added to the RMX unit 10-3 Enabling the Recording Features in a Conference IVR ServiceConference IVR Service Properties dialog box is displayed 10-4 To enable recording for a conferenceEnabling the Recording in the Conference Profile 10-5 Recording Link Encryption 10-6 Recording Link SettingsRecording Link Encryption Guidelines See Enabling the Recording in the Conference Profile on 10-7 Profile Setting RSS Setting Flag Setting Recording Link 10-8 Using the RMX Web Client to Manage the Recording ProcessTo manage the recording process using the right-click menu Managing the Recording Process Name Description 10-9 10-10 Using Dtmf Codes to Manage the Recording Process 10-11 Conference Recording with Codian IP VCRMonitoring the recording participant 10-12 11-1 Users, Connections and Notes 11-2 Listing UsersTo view the users currently defined in the system 11-3 Administrators can add new users to the systemAdding a New User 11-4 Deleting a User 11-5 Changing a User’s PasswordClick OK User’s password is changed 11-6 To disable a userDisabling a User To rename a user To enable a userEnabling a User Renaming a User 11-8 11-9 ConnectionsViewing the Connections List To list the users who are currently connected to the MCU Controlling the user sessions includes User and Connection Management in Enhanced Security ModeManaging the user login process includes Managing RMX users includes Renaming Users Managing the RMX UsersUser Types Disabling/Enabling Users 11-12 Managing the User Login ProcessImplementing Strong Passwords Password Character Composition 11-13 Implementing Password Re-Use / History RulesPassword Length 11-14 Defining Password AgingDefining Password Change Frequency 11-15 Forcing Password ChangeTemporary User Lockout User Lockout 11-16 User Login RecordUser Lockout is an Audit Event Sessions per User Connection TimeoutControlling RMX User Sessions Management Sessions per System 11-18 Session TimeoutErase Session History After Logout 11-19 Using NotesTo create a note 11-20 To open or edit a noteTo delete a note 12-1 Network Services Management Network Primary IP Network ServicesTwo IP Services are defined for the RMX Management Network Default IP Service Conferencing Service 12-3 Default IP Service Conferencing ServiceTo view or modify the Management Network Service Modifying the Management Network 12-4 Management Network Properties IP dialog box opensModify the following fields 12-5 12-6 12-7 12-8 Click the Routers tab Modify the following fields 12-9 DNS Click the DNS tab Modify the following fields12-10 12-11 RMX 2000 only Click the LAN Ports tab 12-12 View or modify the following fields 12-13 Modifying the Default IP Network ServiceFast Configuration Wizard To view or modify the Default IP Service 12-14 Default IP Service Networking IP dialog box opens 12-15 12-16 12-17 Click the Gatekeeper tab Modify the following fields 12-18 12-19 12-20 12-21 12-22 12-23 TOS 12-24 12-25 Click the SIP Servers tab Modify the following fields Send Certificate 12-26 Username@domain name 12-27 12-28 Click the Security tab Modify the following fields 12-29 Ethernet Settings RMX 4000 Only 12-30 Modify the following field 12-31 To monitor signaling status2IP Network Services Properties RMX CS IP IP Network Monitoring 12-32 12-33 3IP Network Services Properties H.323Click the H.323 tab H.323 tab displays the following fields 12-34 12-35 4IP Network Services Properties SIP Servers External Entities Default Management Network ServiceIPv6 Guidelines RMX Internal Addresses 12-37 12-38 Network SecurityNetwork Separation RMX 12-39 To enable Network SeparationEnabling Network Separation 12-40 Enter the Default Router IP Address 12-41 12-42 Click LoginRMX Web Client Welcome screen is displayed 12-43 ISDN/PSTN Network ServicesSupported Capabilities and Conferencing Features Non Supported Capabilities and Conferencing Features 12-44 Adding/Modifying ISDN/PSTN Network ServicesObtaining ISDN/PSTN required information 12-45 To Add an ISDN/PSTN Network Service 12-46 Click Next 12-47 12-48 12-49 Click Next Span Definition dialog box is displayed 12-50 12-51 Click Save & Continue 12-52 Click Save & Close Modifying an ISDN/PSTN Network ServiceMove the slider to the required setting To Modify an ISDN/PSTN Network Service 12-54 Span DefinitionPhones Spans 12-55 12-56 13-1 IVR Services 13-2 IVR Services ListTo view the IVR Services list Button Button Name Descriptions IVR Services Toolbar13-3 Languages button Conference IVR Services list, click the Add SupportedAdding Languages To add a language 13-5 To upload messages to the MCU Message Message Type Category 13-6 13-7 13-8 13-9 Defining a New Conference IVR ServiceDefining a New Conference IVR Service To define a new Conference IVR Service IVR 13-10 13-11 13-12 13-13 13-14 13-15 Message Type Description 13-16 13-17 13-18 13-19 Roll Call Record 13-20 Ivrrollcallusetonesinsteadof 13-21Roll Call Description Message 13-22 Video Description Services 13-23 Operation Dtmf String Permission 13-24 13-25 13-26 New Entry Queue IVR Service Global dialog box opens Entry Queues IVR ServiceDefining a New Entry Queue IVR Service To set up a new Entry Queue IVR Service 13-28 13-29 13-30 Select the voice messages 13-31 13-32 To select the default Conference IVR ServiceIVR Service button To select the Default Entry Queue IVR Service 13-33 ServiceTo modify the properties of an IVR Service To replace the Music file Install Music File window opensReplacing the Music File Adding a Music File 13-35 13-36 To define the format settings for audio messagesCreating Audio Prompts and Video Slides Recording an Audio Message 13-37 Attributes list, select 16.000 kHz, 16Bit, Mono 13-38 To record a new audio message 13-39 13-40 Creating a Welcome Video SlideTo record additional messages, repeat steps 1 to To create a welcome video slide Message Type Message Text File Name Default IVR Prompts and Messages13-41 13-42 13-43 NID 13-44 Ivrmessagevolume Volume Control of IVR Messages, Music and Roll CallTo control the volume of IVR music, messages and Roll Call Ivrmusicvolume 13-46 Ivrrollcallvolume 14-1 Call Detail Record CDR Utility 14-2 CDR FileCDR File Formats CDR File Contents 14-4 14-5 Viewing, Retrieving and Archiving Conference InformationViewing the Conference Records To open the CDR utility 14-6 Refreshing the CDR ListTo refresh the CDR list Menu Option Button Action Retrieving and Archiving Conference CDR RecordsTo retrieve and archive CDR records 14-7 14-8 15-1 Call FlowsDirect Dialing 15-2 Dialing from H.323 Endpoints 15-3 Dialing string 15-4 Dialing from SIP Endpoints 15-5 Gateway IVROptional 15-6 Dialing from ISDN/PSTN Endpoints 15-7 MCU prefix in Gkgw Profile ID 15-8 Interoperability with CMA 15-9 Connection Indications 15-10 Gateway Functionality 15-11 15-12 Configuring the Gateway Components on the RMXDefining the IVR Service for Gateway Calls To define a new Conference IVR Service for gateway calls 15-13 15-14 15-15 15-16 Defining the Conference Profile for Gateway CallsTo define a Conference Profile for Gateway Sessions RMX Management Rarely Used pane, click Gateway Profiles Define the required settings for Encryption and LPRDefining the Gateway Profile To define a new Gateway Profile 15-18 15-19 15-20 15-21 Displaying the Connection Information System ConfigurationClick OK New Gateway Profile is added to the list 15-22 Monitoring Ongoing Gateway SessionsGateway Session Parameters 15-23 Connected Participant Parameters 15-24 Dialing to Polycom DMA 15-25 To set up the Meeting Room for direct dialing 15-26 16-1 Installing the RMX Manager 16-2 Click the Install RMX Manager link 16-3 16-4 Click All Programs Polycom RMX Manager Starting the RMX Manager ApplicationTo use the browser To use the Windows Start menu Click Start Programs 16-6 Connecting to the MCU 16-7 To connect the RMX Manager to an MCU 16-8 16-9 RMX Manager Main Screen 16-10 MCUs Pane 16-11 Conferences PaneMCUs Toolbar MCUs toolbar contains the following buttons Starting a new conference RMX ManagementConferences list toolbar contains the following buttons Monitoring conferences 16-13 List PaneStatus Bar System Alerts MCU State Address BookParticipant Alerts Port Usage Gauges 16-15 Adding MCUs to the MCUs ListConference Templates To add an RMX unit 443 16-16MCU IP FieldDescription 16-17 Start a Reservation Administrator’s Guide, Meeting Rooms onStarting a Conference Starting a Conference from the Conferences Pane 16-19 New Conference General dialog box opens Click the New Reservation button Starting a ReservationTo start a conference from the Reservation Calendar Reservation Calendar is displayed 16-21 16-22 Monitoring Conferences 16-23 Grouping the Participants by MCU 16-24 Start Monitoring/Stop Monitoring 16-25 Modifying the MCU PropertiesTo view and/or modify the MCU Properties To Remove an MCU from the list Disconnecting an MCURemoving an MCU from the MCUs Pane To disconnect an MCU 16-27 Changing the RMX Manager LanguageMCU icon is removed from the MCUs pane To select a language 16-28 Installing RMX Manager for Secure Communication ModeTo install the RMX Manager RMX Management pane, click IP Network Services 16-29 Clear the Secured RMX Communication check boxClick OK Click the DNS tab Enter the Local Domain Name 16-30 Create a Certificate Request 16-31 Set the RMX to Secure Communication Mode 16-32 16-33 Using an Internal Certificate Authority 16-34 Certificate Export Wizard is displayedSelect Base-64 encoded X.509 .CER 16-35 16-36 Successful export message is displayed Click the OK button 17-1 System and Participant Alerts 17-2 System AlertsTo view the System Alerts list 17-3 17-4 Participant AlertsTo view the Participants Alerts list 17-5 System ConfigurationModifying System Flags 17-6 Mcmsparameters tab, the following flags can be modified 17-7 Externaldb Externaldblogin17-8 Version 4.x and earlier enter the IP 17-9 17-10 17-11 17-12 17-13 17-14 17-15 17-16 17-17 Manually Adding and Deleting System FlagsTo add a flag Flag and Value Description Following flags can be manually added to17-18 17-19 17-20 17-21 17-22 17-23 17-24 17-25 17-26 17-27 Sendwideresto To delete a flag17-28 17-29 Legacyepcontentdefaultlayout Flag Values 17-30 Flag Range Default Network SecurityJitcmode System Flag 17-31 Timoutin Minutes Userlockout YES Alive Timeout SessionWindowin Minutes Lastlogin YES Attempts User 17-32 17-33 Range Default Password ManagementForce YES YES/NO Strong Password Policy Minpassword 17-34 Auto Layout ConfigurationCustomizing the Default Auto Layout Default Auto Layout is controlled by 11 flags CPLAYOUT1X2VER Default Value Possible Values17-35 CPLAYOUT1X1 CPLAYOUT1X2 CPLAYOUT1X2HOR 17-36 AUTOLAYOUT5 17-37Predefined 17-38 RMX TimeAltering the clock To Alter the RMX Time 17-39 17-40 Resource ManagementResource Capacity 17-41 Resource Capacity Modes 17-42 Resolution/fps Video Resources UsedResource Usage Continuous Presence WVGA/30 WVGA/25 17-43WCIF/25 WSIF/30 WSIF/60 WCIF/60 High Definition Video SwitchingVoice 17-44 17-45 Video/Voice Port ConfigurationFlexible Resource Capacity Mode Fixed Resource Capacity 17-46 Configuring the Video/Voice Resources in MPM Mode Flexible Resource Capacity Configuring the Video/Voice Resources in MPM+ ModeTo allocate Audio Only ports in MPM+ mode RMX menu, click Setup Video/Voice Port Configuration 17-48 To allocate resources in Fixed Resource Capacity mode 17-49 Resource Type MaximumAudio Only 17-50 17-51 Forcing Video Resource Allocation to CIF Resolution 17-52 To cancel the forcing of CIF resourceTo force CIF resource 17-53 Main toolbar, click Administration Resource ReportResource Report Displaying the Resource Report Column Description Resource Report Display in Flexible Resource Capacity ModeExample An RMX 2000 in Flexible Resource Capacity Mode has 17-54 17-55 Resource Report is displayed as followsPort Gauges 17-56 Resource Report in Fixed Resource Capacity ModeExample An RMX 2000 in Fixed Resource Capacity Mode has 17-57 ISDN/PSTN 17-58 Setting the Port Usage ThresholdPort Usage To Set the Port Usage Threshold 17-59 SIP Dial-in Busy Notification 17-60 Port Usage Gauges 17-61 Port Gauges in Flexible/Fixed Capacity ModesAudio Ports Gauge Video Ports Gauge 17-62 System InformationTo view the System Information properties box RMX 17-63 17-64 Private Mibs Snmp Simple Network Management ProtocolDetailed Description MIB Management Information Base Files Standard MIBs Alarm-MIBSupport for MIB-II Sections MIB H.341 H.323 320MCU-MIB 17-67 17-68 Traps 17-69 Status Trap Content 17-70 To enable Snmp optionDefining the Snmp Parameters in the RMX 17-71 17-72 Click the Traps tabRMX-SNMP Properties Traps dialog box opens 17-73 17-74 RMX-SNMP Properties Security dialog box opens 17-75 Accepted Host IP Address dialog box opensRMX Snmp Properties Security dialog box, click OK 17-76 Audible AlarmsUsing Audible Alarms Audible Alarm Permissions User Customization Configuring the Audible AlarmsWhen selected all audible alarms are immediately stopped Stop Repeating Message 17-78 User Customization window opens 17-79 Replacing the Audible Alarm FileDownload Audible Alarm File window opens 17-80 17-81 Multilingual SettingCustomizing the Multilingual Setting To customize the Multilingual Setting 17-82 Banners Configuration dialog box opensBanner Display and Customization Customizing Banners 17-83 Login Screen BannerBanner Display Customize the banners by modifying the following fields 17-84 17-85 Main Screen Banner 17-86 Backup and Restore GuidelinesSoftware Management 17-87 Using Software ManagementBackup Configuration dialog box opens Browse to the Backup Directory Path and then click Backup 17-88 Browse to the Install Path and then click Install 17-89 Using PingPing RMX To Ping a network entity from the RMX 17-90 Modify or complete the following fields 17-91 Notification SettingsTo configure the notifications 17-92 Following notification options are displayed 17-93 Logger Diagnostic Files Retrieving the Logger Files Following tasks can be performedFile name structure File name format Viewing the Logger File contents 17-96 AuditorAuditor Files Auditor Event History File Storage 17-97 Retrieving Auditor FilesAuditor Files dialog box is displayed 17-98 To retrieve files for storage on a workstationClick Retrieve Files To open the file in the Auditor File Viewer 17-99 Auditor File ViewerAuditor File Viewer is displayed 17-100 Following fields are displayed for each event Mkdir Http 17-101GET Http PUT Http To open an auditor event file stored on the workstation Alerts and FaultsLists Alerts and Faults that are recorded by the Auditor Audit Events 17-103 17-104 TransactionsLists Transactions that are recorded by the Auditor 17-105 17-106 Installing ActiveXActiveX Bypass 17-107 17-108 Resetting the RMXTo reset the RMX 17-109 18-1 Viewing the Status of the Hardware Components 18-2 Button Name Description HW Monitor Pane Toolbar18-3 18-4 Viewing Hardware RMX 2000 Component’s PropertiesHardware Properties dialog box has the following structure 18-5 To view the MCU Properties 18-6 18-7 18-8 To view the Card Properties 18-9 18-10 To View the Supporting Hardware Components PropertiesBackplane Properties Fans Field Description General SettingsFAN Properties 18-11 18-12 LAN 0, LAN 1, LAN 2 Properties 18-13 Viewing Hardware RMX 4000 Component’s Properties 18-14 18-15 18-16 18-17 18-18 18-19 Backplane+ Properties 18-20 18-21 18-22 Diagnostic Mode 18-23 Performing DiagnosticsTo run Diagnostics on a Hardware Component 18-24 18-25 Click the Run Selected Tests button 18-26 Diagnostics MonitoringMCU Monitor 18-27 Cards Monitor 18-28 Error Buffer IP Disconnection Causes Appendix a Appendix A-Disconnection Causes Disconnection Cause Description Not wish to take the call at this time Disconnection Cause Description Returned Disconnection Cause Description Disconnection Cause Description Disconnection Cause Description Disconnection Cause Number Summary Description Isdn Disconnection Causes Disconnection Cause Number Summary Description Enquiry Status CUG Number Summary Description Disconnection Cause Suspended a Resume message cannot be executed by 100 Message with Appendix A-Disconnection Causes Appendix B Alarms Alarm Code Alarm Description CPU slot ID not identified Encryption Server Error. Failed to Alarm Code Alarm Description Free space percentage% free space Blocks Alarm Code Alarm Description GUI System configuration file is invalid Alarm Code Alarm Description Alarm Code Alarm Description Polycom RMX 2000/4000 Administrator’s Guide Produce a Redalarm Alert Adding the appropriate flag is the system configuration DNS System has been configured for Jitc User Name Support cannot be used Appendix C Appendix C-CDR Fields Unformatted File Conference Summary Record Field Description Standard Event Record Fields Event Records Event Types Event Code Event Name Description Billing Code 23 H323 Participant ConnectedNEW Undefined SIP Private SIPRecording Link User Delete Party Continue IPV6 AddressTerminate User ADD Time User UpdateReconnect User SET END Continue Attend PartyOperator Move Party from Back to 2101, 2105 Defined Participant Continue 1, User UpdateUpdate Participant Continue Participant Disconnected Table C-35, Event Fields for Event On page C-22 Conference Start Continue Event Specific Fields Polycom RMX 2000/4000 Administrator’s Guide Field Description Time the conference starts, without any participant Maximum number of participants that can connect to Automatic switching between participants is enabled Table C-6 Any other number Unknown ATT Accunet NTI FXNTI TIE Trunk Field Description Table C-10Event fields for Event 4 ISDN/PSTN Channel Field Description Field Description Field Description User Update Participant Field Description A dial-out connection, participant phone numbers are 323 Tel URL SIP URI User Update Participant Continue Table C-17Event fields for Event 15 H323 Call Setup Field Description Field Description Field Description SIP MCU SIP URI Name sent by the end point Table C-23Event Fields for Event 22 Dtmf Code Failure Verified by authentication Table C-28 Polycom RMX 2000/4000 Administrator’s Guide Destination Conf Field Description MCU Isdn Terminal SIP URI VIP Table C-35 Value Call Disconnection Cause Disconnection Cause Values 191 H323 call close. Remote busy Value Call Disconnection Cause Value Call Disconnection Cause Following MGC Manager events are not supported by the RMX MGC Manager Events that are not Supported by the RMX Appendix C-CDR Fields Unformatted File Appendix D Ad Hoc Conferencing without Authentication Starting a conference uses the following method Ad Hoc Conferencing without Authentication Ad Hoc Conferencing with Authentication Network Polycom RMX 2000/4000 Administrator’s Guide Conference Access with External Database Authentication Network Conference Access Validation All Participants AlwaysPage Network Conference Access Validation Chairperson Only Upon RequestPage Authentication Settings Ad Hoc Settings External Database Application Settings Flag Description and Value To set the System Configuration flags Externaldb  Set the External Server Authentication field to Numeric ID  Set the External Server Authentication field to Enabling External Database Validation for Conferences Access Appendix E Field Description Number of packets arriving out of order. The fol Out of Order Field Description Purchasing a Certificate Switching to Secure Mode Table F-1Create Certificate Request Click Send Details Installing the CertificateTo install the certificate Appendix F-Secure Communication Mode Securityprotocol Enabling Secure Communication ModeWhen Secure Communications Mode is enabled Creating/Modifying System Flags Alternate Management Network Securing an External Database Appendix F-Secure Communication Mode Alternate Management Network Management Network Primary To modify the workstation’s IP addresses Configuring the WorkstationLogged in on the Management Network Separation on Polycom RMX 2000/4000 Administrator’s Guide Appendix G-Configuring Direct Connections to RMX Example IP address near 192.168.1.nn IP Address To connect directly to the RMX Connecting to the Management Network Appendix G-Configuring Direct Connections to RMX To connect to the Alternate Management Network Connecting to the Alternate Management Network Configure the modem as follows Connecting to the RMX via ModemProcedure 1 Install the RMX Manager Procedure 2 Configure the Modem To create a dial-up connection Procedure 3 Create a Dial-up Connection Appendix G-Configuring Direct Connections to RMX Polycom RMX 2000/4000 Administrator’s Guide Appendix G-Configuring Direct Connections to RMX Polycom RMX 2000/4000 Administrator’s Guide Click All Programs Procedure 4 Connect to the RMXTo Connect using the RMX Manager To use the browser To use the Windows Start menu Appendix H Open the OCS Management application Configuring the OCS for RMX 2000/4000Setting the Trusted Host and Static Route for RMX To set the RMX as trusted and define Static Routes in OCS Pool Front End Properties dialog box opens Expand the Enterprise Pools list Click the Host Authorization tab To add RMX to the Routing Roles Page To create the TLS certificate in the OCS Select Create a New Certificate and click Next Delayed or Immediate Request window appearsAvailable Certificate Tasks window appears Organization Information window appears Name and Security Settings window appearsSelect the Mark cert as exportable check box Your Server’s Subject Name window appears Choose a Certification Authority window appears Geographical Information window appears Click Finish MS R2 Assign Certificate Task window appearsCertificate Wizard Completed window appears MS R2 Available Certificates window appears Select Export a certificate to a *.pfx file and click Next Export Certificate Password window appears Certificate Wizard Completed window appears To create the certPassword.txt file Load Front End Properties dialog box opens Page Service DNS Servers Addresses To configure the RMX IP Network Service Defining a SIP Network Service in the RMXPage Polycom RMX 2000/4000 Administrator’s Guide Page Default IP Service Networking IP dialog box, click OK Polycom RMX System Flag Configuration Sipfreevideoresources Flag Name Value and Description ENV Sipfastupdateinterval Conferencing entity routing name@domain name Dialing to an Entry Queue, Meeting Room or ConferenceTo dial in directly to a conference or Entry Queue Enter the conferencing entity SIP URI in the format Active Alarms Active Alarms and Troubleshooting OCS Known Issues Troubleshooting