Force10 Networks S2410s manual Show port all Command Output Example, System Configuration Commands

show port

Example

Force10 S2410		#show port all				Physical		Link	Link	LACP	Flow
Interface	Type		Admin	Physical
			Mode	Mode		Status		Status	Trap	Mode	Mode
----------	------ ------- ---------- ---------- ------ ------- ------- -------
0/1			Enable	10G	Full			Down	Enable	Enable	Disable
0/2			Enable	10G	Full			Down	Enable	Enable	Disable
0/3			Enable	10G	Full			Down	Enable	Enable	Disable
0/4	PC	Mbr	Enable	10G	Full	10G	Full	Down	Enable	Enable	Disable
0/5			Enable	10G	Full			Up	Enable	Enable	Disable
0/6			Enable	10G	Full	10G	Full	Up	Enable	Enable	Disable
0/7	PC	Mbr	Enable	10G	Full	10G	Full	Up	Enable	Enable	Disable
0/8			Enable	10G	Full	10G	Full	Up	Enable	Enable	Disable
0/9	PC	Mbr	Enable	10G	Full	10G	Full	Up	Enable	Enable	Disable
0/10	PC	Mbr	Enable	10G	Full	10G	Full	Down	Enable	Enable	Disable
0/11	PC	Mbr	Enable	10G	Full			Up	Enable	Enable	Disable
0/12	PC	Mbr	Enable	10G	Full	10G	Full	Up	Enable	Enable	Disable
0/13			Disable	10G	Full			Down	Enable	Enable	Disable
0/14			Enable	10G	Full			Down	Enable	Enable	Disable
0/15	PC	Mbr	Enable	10G	Full	10G	Full	Down	Enable	Enable	Disable
0/16			Enable	10G	Full			Up	Enable	Enable	Disable
0/17	PC	Mbr	Enable	10G	Full	10G	Full	Up	Enable	Enable	Disable
0/18	PC	Mbr	Enable	10G	Full	10G	Full	Up	Enable	Enable	Disable
0/19	PC	Mbr	Enable	10G	Full	10G	Full	Up	Enable	Enable	Disable
0/20	PC	Mbr	Enable	10G	Full	10G	Full	Up	Enable	Enable	Disable
0/21	PC	Mbr	Enable	10G	Full	10G	Full	Up	Enable	Enable	Disable
0/22	PC	Mbr	Enable	10G	Full	10G	Full	Up	Enable	Enable	Disable
0/23	PC	Mbr	Enable	10G	Full	10G	Full	Up	Enable	Enable	Disable
0/24			Disable	10G	Full			Down	Enable	Enable	Disable
1/1			Enable					Up	Enable	N/A	Enable
1/2			Enable					Up	Enable	N/A	Enable
Force10 S2410		#

Figure 28 show port all Command Output Example

Interface—Valid unit, slot and port number separated by forward slashes.. This field only displays in the show port all report.

Note: Port IDs 1/1 and 1/2 in Figure 28 are LAGs.

Type—If not blank, this field indicates that this port is a special type of port. The possible values are: Mon—Indicates a monitoring port. Look at the Port Monitoring screens to find out more information. PC Mbr—Indicates a member of a LAG (port channel).

Probe—Indicates a probe port.

Admin Mode—The port administration state. The port must be enabled in order for it to be allowed into the network. It is either enabled or disabled. The default is enabled.

Physical Mode—The desired port speed and duplex mode. In the S2410, all ports are set to auto-negotiate speed and duplex mode.

Physical Status—Indicates the port speed and duplex mode.

Link Status—Indicates whether the Link is up or down.

Link Trap—Indicates whether or not to send a trap when link status changes. The default is enabled. LACP Mode—Displays whether LACP is enabled or disabled on this port.

Flow Mode—Displays whetherflow control is enabled or disabled.

118 System Configuration Commands