![](/images/new-backgrounds/1078616/78616763x1.webp)
INSPECT WIRING AND RECORD ELECTRICAL DATA: |
|
|
|
|
|
|
| ||||||
RATINGS: |
|
|
|
|
|
|
|
|
|
|
| ||
Motor Voltage |
|
| Motor(s) Amps |
|
| Oil Pump Voltage |
|
| Starter Amps |
|
| ||
Line Voltages: Motor |
|
| Oil Pump |
|
| Controls/Oil Heater |
|
|
|
FIELD-INSTALLED STARTERS ONLY:
Check continuity T1 to T1, etc. (Motor to starter, disconnect motor leads T4, T5, T6.) Do not megger
|
| MEGGER MOTOR |
|
|
| ``PHASE TO PHASE'' |
|
|
|
| ``PHASE TO GROUND'' |
| ||||||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||||
|
|
|
|
|
|
|
|
|
|
| ||||||||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| Polarization Ratio: |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
STARTER: | Manufacturer |
|
|
|
|
|
|
|
|
|
|
| ||||||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
| Serial Number |
|
|
|
|
|
|
|
|
|
| |||
Motor Load Current Transformer Ratio |
|
| : |
|
|
|
| Signal Resistor Size |
|
| Ohms |
|
|
| ||||||||||||
Transition Timer Time |
| Seconds |
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||||||||||
Check Magnetic Overloads Add Dash Pot Oil Yes M | No M |
| No M | |||||||||||||||||||||||
Solid State Starter: | Torque Setting |
|
|
|
|
| O'Clock | Ramp Setting |
|
|
|
| Seconds |
CONTROLS: SAFETY, OPERATING, ETC.
Perform Controls Test (Yes/No)
PIC CAUTION
COMPRESSOR MOTOR AND CONTROL CENTER MUST BE PROPERLY AND INDIVIDUALLY CON- NECTED BACK TO THE EARTH GROUND IN THE STARTER. (IN ACCORDANCE WITH CERTIFIED DRAWINGS).
Yes
RUN MACHINE: | Do these safeties shut down machine? |
|
|
| Condenser Water Flow Switch | Yes M | No M |
| Chilled Water Flow Switch | Yes M | No M |
| Pump Interlocks | Yes M | No M |
INITIAL START: |
|
|
|
|
|
|
|
|
|
|
Line Up All Valves in Accordance With Instruction Manual: |
|
| Start Water Pumps and Establish Water Flow | |||||||
Oil Level OK and Oil Temperature OK |
| Check Oil Pump |
|
|
|
| ||||
Check Compressor Motor Rotation (Motor End Sight Glass) and Record: | Clockwise |
|
|
|
|
| ||||
Restart Compressor, Bring Up To Speed. Shut Down. Any Abnormal Coastdown Noise? | Yes* M | No M | ||||||||
*If yes, determine cause. |
|
|
|
|
|
|
|
|
|
|
START MACHINE AND OPERATE. COMPLETE THE FOLLOWING:
A:Trim Charge and Record Under Charge Refrigerant Section on page 51.
B:Complete Any Remaining Control Calibration and Record Under Controls Section (pages
C:Take At Least 2 Sets of Operational Log Readings and Record.
E: After Machine Has Been Successfully Run and Set Up, Shut Down and Mark Shutdown Oil and Refrigerant Levels.
F: Give Operating Instructions to Owner's Operating Personnel. Hours Given:Hours
G: Call your Carrier factory representative to report chiller
SIGNATURES: | DATE |
|
|
| ||
CARRIER | CUSTOMER REPRESENTATIVE |
|
| |||
TECHNICIAN |
| DATE |
|
|
4