Making Measurements Using Spectrum Analyzer Mode
Third Order Intermodulation Measurement (TOI)
|
| RF iF | 48.8 | dBmV | #AT | 40 dB | I |
|
|
|
|
|
| ||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
|
| PEAK |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
|
| LOG |
| TO1 |
| 72. | 1 dB | V |
|
|
|
|
|
|
|
|
|
| |
| 10 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
|
| dB/ |
|
|
|
|
|
|
|
|
|
|
|
|
|
| N dB | PTS | |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| ON | OFF | |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| % | AM | ||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| ON | OFF | |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| TO1 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| ON | OFF | |
| WA | SE |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||
| SC | FS |
|
|
|
|
|
|
|
|
|
|
|
| Power | ||||
|
| COAR |
|
|
|
|
|
|
|
|
|
|
|
| |||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| Menu | ||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| FFT |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
I | CENTER 300.500 | MHZ |
|
|
|
| SPAN | 5.000 | MHZ |
| |||||||||
|
|
|
|
|
| ||||||||||||||
|
|
| XRES | EW 3.0 | kHz |
| VBW 3 kHZ |
| SWP | 1.67 | set |
| |||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Figure
Example: Use the TO1 function to make a measurement.
1.Press [PRESET). Connect two equal amplitude signals with different frequencies, to the spectrum analyzer’s INPUT 75 Q.
2.Press [FREQUENCY) and enter the frequency of one of your input signals to place the signal at the
3.Press (SPANI. Change the span until only the two signals and their two distortion products appear on the display.
4.Press
5.Read the measurement results in the upper left corner of the screen.
6.Press TO1 ON OFF (OFF) to turn the measurement off.