Siemens 200 PMDs with Exponential Flow to Head Function

7ML19981FB06 MultiRanger 100/200 – INSTRUCTION MANUAL Page 79

mmmmm

Open Channel Monitoring

MR 200

PMDs with Exponential Flow to Head Function

For Primary Measuring Devices (PMDs) that measure flow by an exponential equation,

use these parameters. Ensure that you use the correct exponent for your PMD; the values

below are samples only.

Standard Weirs

Applicable Weir Profiles

Paramete r Index Value

P600 G 1 - Exponential Function

P601 GWeir Type Value1

1. Values are samples only. Consult weir manufacturer’s documentation for

correct flow exponent.

V-notch

Suppressed rectangular

Cipolletti or trapezoidal

Sutro or proportional

2.50

1.50

1.00

P603 G Maximum Head

P604 GMaximum Flow

P606 G Time Units

P801 GRange Extension

3 to 4

hmax

Weir Profil e

Transduc er

V-notch or

triangular

suppressed

rectangular

cipolleti or

trapezoidal

sutro or

proportional

Contents

Main Copyright Siemens Milltronics Process Instruments Inc. 2009. All Rights Reserved Disclaimer of Liability Level Measurement Continuous Weighing Systems Tab le of C on te nts The MultiRanger 100 and 200 Specifications Installation Wiring Operating the MultiRanger Relays Backup Level Override Discrete Inputs mA I/O Volume [MR 200] Alarms Pump Control Rake (Screen) Control [MR 200] External Totalizers and Flow Samplers [MR 200] Open Channel Monitoring (OCM) [MR 200] Testing the Configuration MultiRanger Communications Communications Installation Modbus Register Map Data Types Error Handling Communication Troubleshooting Communication Appendix A: Single Parameter Access (SPA) Parameter Reference Appendix A: Index Types Appendix B: Technical Reference Appendix C: Troubleshooting Appendix D: Pump Control Reference Appendix E: Updating Software Programming Charts Appendix F: Upgrading Appendix G: Conduit Entry for Class 1, Div 2 Applications Appendix H: Software Revision History The MultiRanger 100 and 200 MultiRanger 100 MultiRanger 200 The Manual Manual Symbols Configuration Examples Specifications Power Mounting Page Outputs Page Specifications Cable Note: Installation Mounting Mounting Locations Recommended Avoid Mounting Instructions Wall Mount Enclosure Dimensions Mounting the Enclosure Please note: Cable routed through a conduit: Cable exposed and entering through the cable glands: Appendix G: Conduit Entry for Class 1, Div 2 Applications Note: Cable routed through a conduit Panel Mount Panel Mount Dimensions Mounting the Enclosure Helpful hint: MultiRanger Board Installing the Battery Installation Steps Note: Disconnect power before replacing the battery. Installing SmartLinx Card Wiring Please note: Terminal Board Cables Note: Please do not overtighten the screws. Connection Cable Type Transducers MultiRanger 100/200 Installation (for retrofitting MultiRanger Plus Installations) Relays Relay Ratings Power Failure Temperature Sensor mA Input [MR 200 only] mA Output Note Level System Synchronization Power Page 20 MultiRanger 100/200 INSTRUCTION MANUAL 7ML19981FB06 GND L2/NL1 Digital Communications RS-485 Serial Connection RS-232 Serial Connection L1 L2/N Note: Make sure unit is connected to a reliable ground. Page Operating the MultiRanger RUN Mode ? Display Indicator Functions RUN Mode PROGRAM Mode Readings in RUN Mode Icon Index Type Key Function P# Status Parameters Paramete r Values Controlling the Display Display Adjusting the primary reading for four-digit LCD readout: Auxiliary Reading Paramete r Action Multiple Readings [MR 200 only] PROGRAM Mode Starting PROGRAM Mode Hand Programmer Notes Programmer Keys Keys Programming Mode Run Mode Dolphin Plus (compatible with product software versions 1.06 and earlier) Note: Dolphin Plus Toolbar Buttons Button Action SIMATIC Process Device Manager (PDM) (compatible with product software versions 1.07 and later) Device Descript ion Activating the MultiRanger Changing Parameters Helpful Hints Note: Security Simulation Parameters P925P927 Using Units or Percent (%) MR 200 only: Parameter Reset Master Reset (P999) Display Readout Display Definition Page Parame ter In dexing MultiRanger Display Accessing a Parameter Index Notes Note Primary and Secondary Indexes Primary Index Secondary Index Accessing a Secondary Index P111 Starting Measurement Single Point Models A B C Note: on page36 Dual Point Models Index Description Average or Differential [MR 200 only] Measurement Conditions Troubleshooting Appendix Relay Failsafe Response Rate Dimensions [MR 200 only] Relays General Introduction Relay Function Alarm Pump Miscellaneous Relay Status Non Run Modes Relay States Relay Related Parameters Relay Wiring Test Relay Activation P111 Pump and Control functions Relay Logic is Modified Relay Failsafe P129Relay Failsafe Page 46 MultiRanger 100/200 INSTRUCTION MANUAL 7ML19981FB06 Preset Applications Preset applications set up the relay parameters to predetermined values shown below: Value #Parameter s Affec ted Backup Level Override Backup Level Overrid e Backup Level Override Parameters P064: Reading Override Enable P065: Reading Override Value P066: Override Time Delay Discrete Inputs Backup Level Override Discrete Inputs Wiring the Discrete Inputs Programming the Discrete Input Logic mA I/O mA Input [MR 200] Level Reading Parameters mA Output Note: mA LI/O Calibrating 4 mA Output Calibrating 20 mA Output Verifying the mA Range Volume [MR 200] Readings Tank Shape and Dimensions Characterization Chart [MR 200] Example Chart Note: MultiRanger 200 only Paramete r Transducer Index Value Descript ion Alarms Alarms Level Set the Common Parameters Paramete r Index Value Description Rate [MR 200] In Bounds/ Out of Bounds Range [MR 200] Cable Fault Temperature [MR 200] Loss of Echo (LOE) Pump Con trol Setting a Pump Down Grou p Setting a Pump Up (Rese rvoir) Group Page Other Pump Control Algorithms Set Relays to ALTERNATE DUTY BACKUP [MR 200] Set Relays to FIXED DUTY ASSIST Set Relays to FIXED DUTY BACKUP [MR 200] Set Relays to ALTERNATE DUTY SERVICE [MR 200] Set Relays to FIRST IN FIRST OUT (FIFO) ASSIST [MR 200] Set the Relay ON Setpoints [MR 200] Set the Relay OFF Setpoints [MR 200] Optional Pump Controls Starting Pumps by Rate of Level Change [MR 200] Single and Dual Point [MR 200] Rotating Pumps by Service Ratio [MR 200] Notes: Totalizing Pumped Volume [MR 200] Set in RUN Mode Setting Independent Failsafe Controls Setting a Pum p to Run On [M R 200] Setting the Pump Start Delays [MR 200] Reducing Wall Cling [MR 200] Grouping Pumps [MR 200] Setting a Flush Valve [MR 200] Relay Controlled by Communications Tracking Pump Usage Information Available Paramete r Acce ss Rake (Screen) Control Rake (Screen) Control [MR 200] Setting a Rake Control Rake (Screen) Control Setting the Common Parameters Set Relay 1 (Operate Rake) Set Relays 2 to 4 (Level Alarms) P110 2 1 Description External Totalizers and Flow Samplers MR 200 External Totalizers and Flow Samplers [MR 200] Relay Contacts Totalizer Counter Formula Flow Sampler Based on Volume and Time Open Channel Monitoring (OCM) [MR 200] 1. Dimensional (P600 = 2,3,6,7) 2. Exponential (P600 = 1) 3. Universal (P600 = 4,5) Common Parameters Setting Zero Head Setting Totalized Volume Applications Supported by MultiRanger 200 BS-3680 / ISO 1438/1 Thin plate V notch weir BS-3680 / ISO 4359 Rectangular Flume Palmer Bowlus Flume H Flume Flume Size (Diameter in feet) Point of Measurement cm inches PMDs with Exponential Flow to Head Function Standard Weirs Applicable Weir Profiles Non-Applicable Weir Profiles Parshall Flume Leopold Lagco Flume Cut Throat Flume Universal Calculation Support Typical Flow Characterization Volume Example Flumes Example Weirs Testing the Configuration Simulation Simulating a Single Measurement To verify Reading calculations (P920 to P926) Simulating a Level Cycle Checking Volume Characterization [MR 200] To confirm universal volume calculations (P050 = 9, 10) are correct: Checking OCM Flow Characterization [MR 200] To confirm universal flow calculations (P600 = 4, 5) are accurate: I/O Checkout Discrete Inputs Discrete Inputs mA Input [MR 200] mA Output General Appendix C: Trouble shoot ing MultiRanger Communications MultiRanger Communication Systems Modbus Dolphin Optional SmartLinxCards Communication Systems Communication Ports RS-232 RS-485 Modbus SmartLinx Dolphin Plus Dolphin Communications Installation Wiring Guidelines Ports 1 and 2 Ports 1 and 2: RS-232 RJ-11 Jack and RS-485 Locations Note: Port Wall Mount Port 1: RS-232 RJ-11 Jack COM55 A32 Rx To connect the unit to a PC using an RS-232 jack, use the cable as shown: Note: Configuring Communication Ports (Parameters) The unique identifier of the MultiRanger on the network. P770 Port Protocol The communications protocol used between the MultiRanger and other devices. P771 Network Address P772 Baud Rate The communication rate with the master device. The number of bits between the data bits. P773 Parity The serial port parity. P778 Modem Available Sets the MultiRanger to use an external modem. Paramet er A cces s P779 Modem Inactivity Timeout Sets the time that the unit will keep the modem connected with no activity. Modbus Register Map Average or Difference Appendix A Data Types mA input Word Order (R40,062) Unsigned Double Precision Integer (UINT32) Parameter Access (R43,998 R46,999) Map ID (R40,063) P782 Parameter Index Location Product ID (R40,064) Point Data (R41,010 R41,031) Available registers: The reading is expressed as a percentage of full scale, multiplied by 100: Totalizer (R41,040 R41,043) Input/Output (R41,070 R41,143) Discrete Inputs (R41,070) Relay Outputs (R41,080) mA Input (R41,090) [MR 200] mA Output (R41,110-41,111) Pump Control (R41,400 R41,474) Pump OFF Setpoint (R41,430 R41,435) Pumped Volume (R41,440 R41,443) [MR 200] Parame ter R efe renc e Parameter Reference Parameter Access (R43,998 R46,999) Format Words (R46,000 to R46,999) Parameter Specific Index Method Global Index Method Parame ter In dexing Reading Parameters Global Index Method (P782 = 0) Text Messages Split Values Bit Values Writing Parameters Global Index Method (P782 = 0) Parameter Specific Index Method (P782 = 1) Format Words (R46,000 to R46,999) Parameter P782 Parameter Index Location Global Index Method (P782 = 0) Parameter-Specific Index Method (P782 = 1) Format Registers Decimal Offset Example Format Primary Index Secondary Inde x Decimal Data Types Numeric Values Bit Values Unsigned Double Precision Integer (UINT32) Word Order (R40,062) Split Values One example is P807, Transducer Noise, where: Text Messages Number Text Message as displayed on LCD Relay Function Codes (P111 Only) Parame ter R efer ence Control Relay Function Code Number P111 Error Handling Error Handling Modbus Responses Error Handling Code Name Meaning Page Communication Troubleshooting Generally Specifically Communication Appendix A Communication Appendix A: Single Parameter Access (SPA) Mapping Reading Parameters Address Description Communication Appendix A Writing Parameters Format Register Bits Values Description Error Codes Parameter Reference MultiRanger 100 and MultiRanger 200 Helpful Hints Accessing a Secondary Index Index types Name Description # of indexes 7ML19981FB06 MultiRanger 100/200 INSTRUCTION MANUAL Page 119 P000 Lock Secures the MultiRanger from changes via the handheld programmer. Quick Start (P001 to P007) P001 Operation For DPD and DPA Programming [MR 200] Single Point Model Use Specifies material type. P002 Material Operation [index] Available Values 7ML19981FB06 MultiRanger 100/200 INSTRUCTION MANUAL Page 121 P003 Maximum Process Speed Determines level change reaction. Specifies the Siemens Milltronics transducer connected to the unit. P004 Transducer Page 122 MultiRanger 100/200 INSTRUCTION MANUAL 7ML19981FB06 P005 Units Specifies measurement units used for dimensional values. P006 Empty Enter distance in units (P005) from the face of the transducer to the process empty point. P007 Span Volume (P050 to P055) [MR 200] P050 Tank Shape [MR 200] Enter the Tank Shape value matching the monitored vessel or wet well. Maximum Volume (P051) #Shape Description P051 Maximum Volume [MR 200] Note: Examples: P052 Tank Dimension A [MR 200] Dimension A as used in P050 Tank Shape. P053 Tank Dimension L [MR 200] Dimension L as used in P050 Tank Shape. P054 Level Breakpoints (Universal Volume Calculation) [MR 200] Display and Reading (P060 to P062) P060 Decimal Position P061 Convert Reading [MR 200] Multiplies the current value by the specified amount to allow for scaling. Volume Examples: P062 Offset Reading Backup Level Override P064 Reading Override Enable Sets the discrete input to act as the source for a level reading override. P065 Reading Override Value P066 Override Time Delay Defines the time used to calm (debounce) the override condition input. Set in seconds. P069 Password Holds the current password for P000. Select by typing in 069. You cannot scroll to this parameter. Paramet er Index Value Failsafe (P070 to P072) P070 Failsafe Timer The time for invalid measurements to elapse before Failsafe State activates. Once activated, the Failsafe State initiates the following: P129 Relay Failsafe Relays (P100 to P119) Preset Applications (P100) Control Functions (P111) Setpoin ts (P112 , P113) Note: P100 Preset Applications [MR 200] Six preset applications to configure or bench test the unit. P110 Level Source Sets the level source on which the indexed relay is assigned to a measurement point. . MultiRanger 200 In Single Point Mode (standard): Control Type #1 Communications communications the parameter values are mapped to different numbers. See on page 89 for Modbus information or the relevant SmartLinxmanual. Relay Control P112 Relay ON Setpoint Control Type #1Relay Control MultiRanger Communications Sets the process point at which the relay changes from its NORMAL state. P113 Relay OFF Setpoint Sets the process point at which the relay returns to its NORMAL state. The distance above and below the bound alarm setpoints. P115 Relay Interval Setpoint [MR 200] The length of time in hours between starts. P118 Relay Output Logic The logic applied to relays to determine the contact open or closed state. Relay Control Function Power Failure Value Logic Alarm Contact Pump Setpoint Modifiers (P121 and P122) [MR 200] P121 Pump by Rate [MR 200] P122 Pump Service Ratio [MR 200] Selects pump usage based on the RUN time ratio rather than last used. Independent Relay Failsafe (P129) P129 Relay Failsafe Sets how individual relays react to a failsafe condition, to allow for more flexible programming. To select an independent Relay Failsafe value: Advanced Pump Control Modifiers (P130 to P137) [MR 200] P130 Pump Run-On Interval [MR 200] Sets the number of hours between pump run-on occurrences. Relay Function (P111) Preset (P129) P131 Pump Run-On Duration [MR 200] Sets the number of seconds that the pump runs on. P132 Pump Start Delay [MR 200] Sets the minimum delay (in seconds) between pump starts. P133 Pump Power Resumption Delay [MR 200] P136 Wall Cling Reduction [MR 200] Varies the upper and lower setpoints to reduce material buildup on the walls. P137 Pump Group [MR 200] Puts pumps into groups for multiple pump rotations on one transducer. Flush Systems (P170 to P173) [MR 200] Single Point Mode Dual Point Mode P170 Flush Pump [MR 200] Picks the number of the pump relay which triggers the flushing device. P171 Flush Cycles [MR 200] Sets the number of pump cycles requiring flush control. The length of time for each flush cycle that the flush control is active. If three flush cycles are required after every ten pump cycles then: P172 (Flush Interval) = 10 P171 (Flush Cycles) = 3 mA Output (P200 to P219) P200 mA Output Range Determines the mA output range. P201 mA Output Function Alters the mA output/measurement relationship. P202 mA Output Allocation Sets the input source from which the mA output is calculated. Please note that parameter P202 values vary between the MultiRanger 100 and the MultiRanger 200. P203 mA Output Value / Transducer Displays current mA output value for the Point Number. Note: Independent mA Setpoints (P210 and P211) P210 0/4 mA Output Setpoint Sets the process level corresponding to the 0 or 4mA value. P211 20 mA Output Setpoint Sets the process level that corresponds to the 20 mA value. mA Output Trim (P214 to P215) P214 4 mA Output Trim Calibrates the 4 mA output. P215 20 mA Output Trim Calibrates the 20 mA output. mA Output Failsafe (P219) [MR 200] P219 mA Output Failsafe [MR 200] Use for failsafe operation, independent of the Failsafe Material Level (P071). Selecting an independent mA Failsafe option: mA Input (P250 to P260) [MR 200] P250 mA Input Range [MR 200] Shows the mA input range of the connected mA device. P251 0 or 4 mA Input Level [MR 200] Shows the process level corresponding to the 0 or 4 mA value. P252 20 mA Input Level [MR 200] Discrete Input Functions (P270 to P275) P270 Discrete Input Function Sets how discrete signals are interpreted by the MultiRanger. P275 Scaled Discrete Input Value Shows the current value of the discrete input after any scaling is applied. Standard Data Logging (P300 to P321) Record Temperatures (P300 to P303) Range of Values Function (P270) P300 Temperature, Transducer Maximum P301 Temperature, Transducer Minimum P302 Temperature, Sensor Maximum P303 Temperature, Sensor Minimum Record Readings (P304 and P305) P304 Reading Max Shows the highest Reading calculated (in normal Reading units or %). P305 Reading Min Shows the lowest Reading calculated (in normal Reading units or %). P309 Pump RUN Time Displays the amount of time in minutes since a relay was last activated. P310 Pump Hours View or reset the accumulate ON time for the displayed Relay Number. P311 Pump Starts Flow Records (P320 and P321) [MR 200] P320 Flow Max [MR 200] View the highest flow rate calculated (in units or %). P321 Flow Min [MR 200] View the lowest flow rate calculated (in units or %). Profile Records (P330 to P337) Note: WARNING: P330 Profile Record 7ML19981FB06 MultiRanger 100/200 INSTRUCTION MANUAL Page 161 P331 Auto Record Enable Use to enable/disable the Auto Profile Record function. P332 Auto Record Transducer Specifies the Transducer Point Number for which Auto Profile Records are saved. Please note that Differential and Average operation is a MultiRanger 200 feature. Auto Record ON and OFF Setpoints (P334 to P337) P334 Auto Record ON Setpoint P335 Auto Record OFF Setpoint P336 Auto Record Filling / Emptying P337 Auto Record LOE Time Limits Auto Profile Records from being saved unless extended LOE occurs. Page 164 MultiRanger 100/200 INSTRUCTION MANUAL 7ML19981FB06 Installation Records (P340 to P342) P340 Date of Manufacture The number of times power has been applied since the Date Of Manufacture. View the date of manufacture of this MultiRanger unit. P341 RUN Time Open Channel Monitoring (P600 to P621) [MR 200] Open Channel Monitoring Note: P801 Range Extension The type of primary measuring device (PMD) used. P601 Flow Exponent [MR 200] The Exponent for the flow calculation formula. Single Point Model Dual A Word on Exponents 7ML19981FB06 MultiRanger 100/200 INSTRUCTION MANUAL Page 167 P602 Primary Measuring Device Dimensions [MR 200] The dimensions of the Primary Measuring Device (PMD). PMD Type Exponent (sample only) P603 Maximum Head [MR 200] The level value associated with Maximum Flow, in Units (P005). P604 Maximum Flow [MR 200] The maximum flowrate associated with Maximum Head (P603). 7ML19981FB06 MultiRanger 100/200 INSTRUCTION MANUAL Page 169 P605 Zero Head [MR 200] The distance above Empty (P006) in Units (P005) representing zero head (and zero flow). Conditions Enter Page 170 MultiRanger 100/200 INSTRUCTION MANUAL 7ML19981FB06 P606 Time Units [MR 200] Determines the units used to display current flow and logging flow values. This is used when the Primary Measuring Device is Ratiometric (P608=0). P607 Flowrate Decimal [MR 200] The maximum number of decimal places to be displayed. P608 Flowrate Units [MR 200] The volume units used to display total flow. Note: P610 Head Breakpoints [MR 200] Head vs. Flowrate (P610 and P611) P611 Breakpoint Flowrates [MR 200] The flowrate corresponding to each Head Breakpoint entered. P620 Low Flow Cutoff [MR 200] Eliminates totalizer activity for flows at or below the cutoff value. P621 Auto Zero Head [MR 200] Calibrates Zero Head (P605) based on actual head measurements. Before using this feature, verify the following parameters are correct: Pumped Volume Totalizer (P622) [MR 200] * or discharge P622 Inflow / Discharge Adjust [MR 200] The method used to calculate the volume pumped, for pumped total Operation (P001 = 7). Totalizer (P630 to P645) [MR 200] P630 LCD Totalized Multiplier [MR 200] Use this feature if the LCD Total increments by too large (or too small) an amount. P633 LCD Totalized Decimal Position [MR 200] Enter the maximum number of decimal places to be displayed. P640 Remote Totalized Multiplier [MR 200] Note: 7ML19981FB06 MultiRanger 100/200 INSTRUCTION MANUAL Page 177 P641 Flow Sampler Mantissa [MR 200] This parameter is relevant only if Operation is set to OCM (P001 = 6). Enter the mantissa (Y) for the exponent (Z) in the formula: Flow Sampler Increment = Y x 10Z Flow units. Example: Range Calibration (P650 to P654) There are two types of calibration possible: P650 Offset Calibration Calibrates Empty (P006) if the reported level is consistently high or low by a fixed amount. Before using this feature, verify the following parameters are correct: Offset Calibration P651 Sound Velocity Calibration P652 Offset Correction The value altered when an Offset Calibration is performed. P653 Velocity Note: P654 Velocity at 20C Temperature Compensation (P660 to P664) P660 Temp Source Source of the temperature reading used to adjust the speed of sound. P661 Temp Fixed Use this feature if a temperature sensing device is not used. P663 Temperature Transducer Allocation This feature may only be used for differential or average Operation (P001 = 4 or 5). P664 Temperature Rate (P700 to P708) P700 Max Fill Rate P003 Value Meters/Minute Page 184 MultiRanger 100/200 INSTRUCTION MANUAL 7ML19981FB06 P701 Max Empty Rate P702 Filling Indicator The fill rate required to activate the LCD Filling indicator ( ). P003 Value Meters / Minute P703 Emptying Indicator The empty rate required to activate the LCD Emptying indicator ( ). P704 Rate Filter Damps Rate Value (P707) fluctuations. Page 186 MultiRanger 100/200 INSTRUCTION MANUAL 7ML19981FB06 P705 Rate Update Time chart on page23. Readings in RUN Mode P706 Rate Update Distance The material level change (in metres) to initiate a Rate Value update. Measurement Verification (P710 to P713) P710 Fuzz Filter P711 Echo Lock Use this feature to select the measurement verification process. P712 Echo Lock Sampling Adjusts the size of the Echo Lock Window. P713 Echo Lock Window P711 value P712 preset value Transducer Scanning (P726 to P729) P726 Level System Sync Enables the System Sync on the terminal block. P727 Scan Delay The delay, in seconds, between measurements from transducer points (dual point model only). Display (P730 to P739) P730 Auxiliary Reading Selecting the Auxiliary Reading operation P731 Auxiliary Reading Key Enter the Parameter Number whose value is to be displayed in the Auxiliary Reading field Hand Programmer P732 Display Delay Adjusts the Point Number display scroll speed. P735 Backlight Controls the LCD backlighting. P737 Primary Reading [MR 200] The reading shown on the primary reading display when in RUN mode. P741 Communications Timeout SmartLinx Reserved (P750 to P769) Communications (P770 to P782) Communications P770 Port Protocol The communications protocol used between the MultiRanger and other devices. P772 Baud Rate The communication rate with the master device. The number of data bits per character. P773 Parity The serial port parity. P775 Stop Bits The number of bits between the data bits. P778 Modem Available Sets the MultiRanger to use an external modem.. P779 Modem Inactivity Timeout SmartLinx Hardware Testing (P790 to P795) P790 Hardware Error The results of ongoing hardware tests in the communications circuitry. Note: Paramete rs P791 Hardware Error Code P792 Hardware Error Count P794 SmartLinx Module Type P795 SmartLinx Protocol P799 Communications Control Echo Processing (P800 to P807) P800 Near Blanking The space near the transducer face which cannot be measured. P801 Range Extension Allows the material level to fall below the Empty setting without reporting LOE. P802 Transducer with Submergence Shield Used when the transducer is expected to be submerged on occasion. P803 Shot / Pulse Mode Determines what type of ultrasonic shots are fired. Note: P804 Confidence Threshold Determines which echoes are evaluated by software. P805 Echo Confidence Displays the echo confidence of the measurement echo from the last shot. Noise Problems P806 Echo Strength P807 Noise Advanced Echo Processing (P815 to P825) P815 Echo Time Filtered The time (in ms) from the transmit pulse to the processed echo. The time (in ms) from the transmission of the pulse, to when it is processed. P816 Echo Time Raw P820 Algorithm Chooses the algorithm to generate the measured value from the profile. P821 Spike Filter Dampens spikes in the echo profile to reduce false readings. P822 Narrow Echo Filter Filters out echoes of a specific width. P823 Reform Echo Smoothes jagged peaks in the echo profile. P825 Echo Marker Trigger The point on the primary echo on which the measured value is based. Advanced TVT Adjustment (P830 to P835) P830 TVT Type Selects the TVT Curve used. P831 TVT Shaper Turns the TVT Shaper ON or OFF. P832 TVT Shaper Adjust P833 TVT Start Min P834 TVT Start Duration P835 TVT Slope Min Enter the minimum slope (in dB/s) for the middle of the TVT Curve. P837 Auto False-Echo Suppression Values Display before Auto False Echo Suppression (or when P837 = 0) P838 Auto False-Echo Suppression Distance Values Set Up: P839 TVT Hover Level Values Advanced Shot Adjustment (P840 to P852) This value is automatically altered by Maximum Process Speed (P003). These parameters are for Siemens Milltronics service personnel only. P840 Short Shot Number The number of short shots to be fired (and results averaged) per transmit pulse. P842 Short Shot Frequency Adjust the short shot transmit pulse frequency (in kHz). This feature is automatically altered when Transducer (P004) is altered. P843 Long Shot Frequency Adjust the long shot transmit pulse frequency (in kHz). P845 Long Shot Width Adjust the width (in ms) of the long shot transmit pulse. This feature is automatically altered when Transducer (P004) is altered. P850 Short Shot Bias P851 Short Shot Floor Tes t (P 90 0 t o P9 13) Test Parameters are intended for use by Siemens Milltronics Service personnel. P900 Software Revision Number View the EPROM Rev. #. P901 Memory P902 Watchdog P903 Display P904 Keypad P905 Transmit Pulse P906 RS-232 Port P908 Scanner P910 Toggle Relays P911 mA Output Value P912 Transducer Temperature P913 Sensor Temperature Measurement (P920 to P927) To Access in RUN Mode Testing the Configuration P920 Reading Measurement Corresponds to the final reading after all programming is applied. P921 Material Measurement The distance between the monitored surface and the transducer face. The distance in Units (P005) or % of Span (P007) between Empty (P006) and the monitored surface. P922 Space Measurement The distance between the monitored surface and Span (P007). P924 Volume Measurement [MR 200] Please note that Head Measurement is a MultiRanger 200 feature only. The calculated vessel capacity in Max Volume (P051) or % of Max Volume. Please note that Volume Measurement is a MultiRanger 200 feature only. P925 Flow Measurement [MR 200] Master Reset (P999) This feature resets all parameters to original values. Page Appendix A: Index Types Index types Name Description # of indexes Appendix B: Technical Reference Transmit Pulse Echo Processing Dolphin Plus Display TVT (Time Varying Threshold) curves Auto False-Echo Suppression Display before Auto False Echo Suppression (or when P837 = 0) Display after Auto False Echo Suppression Distance Calculation Sound Velocity Scanning Volume Calculation [MR 200] Universal, Linear (P050 = 9) Universal, Curved [MR 200] Select at least enough breakpoints from the curve to satisfy the following: Flow Calculation Universal, Linear [MR 200] Typical Flow Characterization Universal, Curved [MR 200] Select at least enough breakpoints from the curve to satisfy the following: Typical Flow Characterization Maximum Process Speed Paramete r Values Dependent on Maximum Process Speed (P003) (units) 1 (slow) 2 (medium) 3 (fast) 7ML19981FB06 MultiRanger 100/200 INSTRUCTION MANUAL Page 231 Appendix C: Troubleshooting Sound Velocity Appendix C: Troubleshooting If the setup becomes too confusing use P999 to reset and start again. Common Problems Chart Note: Symptom Cause Action Noise Problems Determine the Noise Source Non-Transducer Noise Sources Acoustical Noise - removed + removed Go to: Non-Transducer Noise Sources Common Wiring Problems Reducing Electrical Noise Reducing Acoustical Noise Measurement Difficulties Flashing LOE Display LOE occurs when: If LOE is displayed, check the following: Adjust Transducer Aiming Fixed Reading Obstructions in the Sound Beam Nozzle Mountings Set the MultiRanger to Ignore the Bad Echo If the Echo is Close to the Transducer Wrong Reading Types of Wrong Readings Liquid Splashing Adjust the Echo Algorithm Transducer Ringing Normal Ring Down Poor Ring Down Unit Repair and Excluded Liability Appendix D: Pump Control Reference Pump Control Options Pump Duty Pump Start Method Pump Groups Fixed Duty Assist (P111 = 50) Fixed Duty Backup (P111 = 51) [MR 200] Alternate Duty Assist (P111 = 52) Alternate Duty Backup (P111 = 53) [MR 200] Service Ratio Duty Assist (P111 = 54) [MR 200] Service Ratio Duty Backup (P111 = 55) [MR 200] First In First Out (FIFO) (P111 = 56) [MR 200] Pump by Rate (P121) [MR 200] Starts pumps until the level is changing at the rate specified in P702 or P703. Other Pump Controls [MR 200] Pump Run-On (P130, P131) Wall Cling Reduction (P136) Pump Group (P137) Page Appendix E: Updating Software Updating Software Appendix F: Upgrading Mounting a MultiRanger 100/200 Installation Connecting the Transducer Important: Connecting a transducer with RG62 coaxial extension cable MultiRanger Plus to MultiRanger 100/200 Parameters MultiRanger Plus Relay Paramete r Value Relay Paramet er Value Appendix G 7ML19981FBO6 MultiRanger 100/200 INSTRUCTION MANUAL Page 249 Appendix G: Conduit Entry for Class 1, Div 2 Applications EXPLOSION HAZARD RPC SN 23650314 0 FORCLASS1 DIV 2 APPLICATIONS Appendix G B 23650314 0 Appendix H: Software Revision History MultiRanger 100 Page Page MultiRanger 200 Page Page 7ML19981FB06 MultiRanger 100/200 INSTRUCTION MANUAL Page 257 Programming Charts Page 258 MultiRanger 100/200 INSTRUCTION MANUAL 7ML19981FB06 7ML19981FB06 MultiRanger 100/200 INSTRUCTION MANUAL Page 259 Page 260 MultiRanger 100/200 INSTRUCTION MANUAL 7ML19981FB06 7ML19981FB06 MultiRanger 100/200 INSTRUCTION MANUAL Page 261 Page 262 MultiRanger 100/200 INSTRUCTION MANUAL 7ML19981FB06 7ML19981FB06 MultiRanger 100/200 INSTRUCTION MANUAL Page 263 Page Index Page Page Page Page Page Page *7ml19981FB06* www.siemens.com/processautomation