Clocks and Power Manager

3.5.6Power Manager GPIO Edge Detect Status Register (PEDR)

The PEDR, Table 3-12, indicates which of the GPIO pins enabled through the PWER, PRER, and PFER registers caused a wake up from sleep mode. The bits in PEDR can only be set on a rising or falling edge on a given GPIO pin. If PRER is set, the bits in PEDR can only be set on a rising edge. If PFER is set, the bits in PEDR can only be set on a falling edge. To reset a bit in PEDR to zero, write a 1 to it. The PEDR bits are reset to zero in hardware, watchdog, and GPIO resets.

This is a read/write register. Ignore reads from reserved bits. Write zeros to reserved bits.

Table 3-12. PEDR Bit Definitions

 

 

 

 

0x40F0_0018

 

 

 

 

 

 

 

 

PEDR

 

 

 

 

 

 

Clocks and Power Manager

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Bit

31 30 29 28 27

26

25 24 23

22 21 20

19

18 17 16 15

14 13 12

11

10

9

8

7

6

5

4

3

2

1

0

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Reserved

 

 

 

 

 

 

 

 

ED15

ED14

ED13

ED12

ED11

ED10

ED9

ED8

ED7

ED6

ED5

ED4

ED3

ED2

ED1

ED0

Reset

0

0

0

0

0

0

 

0

0

 

0

0

0

0

0

0

0

0

0

0

0

0

0

0

0

0

0

0

0

0

0

0

0

0

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Bits

 

 

Name

 

 

 

 

 

 

 

 

 

 

 

 

Description

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

[31:16]

 

 

 

 

 

Reserved.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Read undefined and must always be written with zeroes.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Sleep mode Edge Detect Status

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

[15:0]

 

 

EDx

 

 

0 – Wake up on GPx not detected.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

1 – Wake up due to edge on GPx detected.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Cleared by hardware, watchdog, and GPIO resets. Cleared by writing a 1.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

3-28

Intel® PXA255 Processor Developer’s Manual

Page 90
Image 90
Intel PXA255 manual Power Manager Gpio Edge Detect Status Register Pedr, Pedr Bit Definitions, 0x40F00018