NEC nd-20292 manual Ibm Lcr

(capital letters only) and enter the following: l:IPL.DO and depress the RETURN key to enter the data. Display shows:

1983/05/o i 14:22:43 (C) Microsoft #l

n:-::~::~~:~	TEXT	TELCOM	- _-
-.-	-.-	-.-	-.-
-.-	-.-	-.-	-.-
-.-	-.-	-.-	-.-
-.-	-.-	-.-	-.-
-.-	-.-	-.-	-.-
Load from	l:IPL.DO

i 983/05/o i 14:28:13 (C) Microsoft #l

~~~~~~~	TEXT	TELCOM	-. -
-.-	-.-	-.-	-.-
-.-	-.-	-.-	-.-
-.-	-.-	.-	-.-
-_-	-.-	-.-	-.-
.-	.-	-.-	-.-
Save as

3.The computer now is prompting for the file name that the file will be stored in RAM. Enter IPL.DO and then depress the RETURN key to enter the data. Display shows:

1983/05/o i	14:29:04		(C)	Microsoft #l
n
~~~r~~	TEXT	TELCOM		-.-
-.-	-.-		-.-	-.-
-.-	-.-		-.-	-.-
-.-	-.-		-.-	-.-
-.-	-.-		-.-	-.-
-.-	.-		-.-	-.-
Save as	IPL.DO	Readv’,

4.Depress the RETURN key or the letter Y (for yes). Display shows:

1983/05/o 1	14:31:24		(C) Microsoft		#1
cj
~~~~~~	TEXT	TELCOM		IPL*DO
-.-	-.-		-.-	-.-
.-	-.-		-.-	-_-
.-	-.-		-.-	-.-
.-	-.-		-.-	-.-
-.-	-.-		-.-	-.-
Load	Save	Name		List	12374

ND-20292

CHAPTER 7

APRIL, 1990

upper right of the display (IPL*DOl indicating that the file IPL.DO has been set as the new automatic loading file. Display shows:

1983/05/o i 14:31:24 (C) Microsoft #l

D

~~~~~~ TEXT TELCOM IPL*DO

-.-	-.-	-.-		-.-
-.-	-.-	-.-		-.-
-.-	-.-	-.-		-.-
-.-	-.-	-.-		-.-
-.-	-.-	-.-		-.-
Load	Save	Name	List	12374

6.Now perform a Warm Start by depressing the RESET button located on the rear of the computer. The LCR Main Menu should appear in the display after a few seconds.

750.6INITIALIZING IBM COMPATIBLE PCs

Equipment Required

1.IBM XT, IBM AT, or NEC APC IV must be locally provided.

NOTE: The IBM type version LCR software will run on either a 1.2mb high density disk drive or a 360kb low density disk drive.

2.IBM LCR version diskette (available on a 5.25” or a 3.5”diskette).

3.Operating system on the IBM PC XT or AT or NEC APC IV has to be MS-DOS@ (Equivalent to NEC APC IV MS-DOS 3.2).

Executing IBM Type Software

1.Insert the LCR diskette into an available disk drive. After verifying the drive prompt on the screen corresponds to the drive where the LCR diskette is located, enter LCR.

2.Depress el (Enter). Display shows:

***LCR MAIN MENU***

1 DOWN LOAD 6 PRINT OUT

; SYSTEM DATA CLEAR

: &i?VAD
4 MODIFY	9
5 DISPLAY	10 SYSTEM CONTROL
ENTER MENU	NO.

5.Using the cursor movement keys, move the cursor to the upper right corner of the display over the file name IPL.DO. Depress the SHIFT key. While the SHIFT key is depressed, depress the fol key. Note that an asterisk is inserted in the file name at the

IBM LCR

1.When UP/DOWN LOADING or verifying, there is a message after completion:

700- 19