Manuals / Nortel Networks / Communications / Telephone

Nortel Networks 1000E warranty Import Node Files web, Click Import

Models: 1000E

1 490

Download 490 pages 31.09 Kb

Page 374

Page 374 of 488 Configuring an IP telephony node

Figure 133

Import Node Files web page

3Click Import.

Click OK in the dialog when the operation is complete. The Node Summary web page is re-displayed showing the new node.

End of Procedure

Reviewing and submitting IP telephony node configuration files

Follow Procedure 95 to review and submit IP telephony node configuration files.

Procedure 95

Reviewing and submitting IP telephony node configuration

1From the Node Summary web page (see Figure 99 on page 322), click Edit to view the node parameters.

The Edit web page appears as shown in Figure 100 on page 323.

553-3041-210 Standard 4.00 September 2007

Image 374

Nortel Networks 1000E warranty Import Node Files web, Click Import

Contents

Installation and Configuration Communication Server 1000EPage July Revision historySeptember August 4 of 488 Revision history Standard 4.00 September Contents Telephones Rack-mounting the components Installing software on the CS 1000E Installing and configuring the Signaling Server software Installing software on an MG 1000E Small System Controller Connecting a Terminal Server Installing and cross-connecting a trunk card Installing the Main Distribution Frame Installing and configuring IP Phones Basic system telephony configuration Implementation summary 16 of 488 Contents List of Procedures 18 of 488 List of Procedures List of Procedures Page 19 20 of 488 List of Procedures List of Procedures Page 21 22 of 488 List of Procedures List of Procedures Page 23 24 of 488 List of Procedures List of Procedures Page 25 26 of 488 List of Procedures List of Procedures Page 27 28 of 488 List of Procedures Standard 4.00 September About this document Subject Related information Applicable systemsConventions Following NTPs are referenced in this document CD-ROM 32 of 488 About this document Standard 4.00 September Introduction Safety instructionsContents Lifting system equipment Handling circuit cards Installing telephones Using telephones 36 of 488 Safety instructions Installation summary Installation tasks List of required installation tasks Part 1 Task Go to List of required installation tasks Part 2 Task Go to 40 of 488 Installation summary Standard 4.00 September System components CS 1000E Call Server CS 1000E Core Call Server top view Backup and restore enhancements CS 1000E Core Call Server front view New backup rules Signaling Server Network Routing Service Element Manager web server NTDU27 Server Installation and Configuration Signaling Server profile Part 2 Property Description CD-ROMand floppy drives Maintenance port Connectors on the front of the Signaling Server Media Card profile Part 1 Property Description Connectors at the back of the Signaling ServerMedia Card Media Card profile Part 2 Property Description Media Card Media GatewayMedia gateway is shown in on page 52 and described on NTDU14 Pair Cable Connectors on the Media GatewayMedia Gateway profile Part 1 Property Description Media Gateway profile Part 2 Property Description Media Gateway profile Part 3 Property Description Connectors at the back of the Media Gateway Front of the Media Gateway Media Gateway Expander profile Part 1 Property Description Media Gateway ExpanderMedia Gateway Expander NTDU15 Media Gateway Expander profile Part 2 Property Description Media Gateway Expander profile Part 3 Property Description Order Code Description Qty Connectors at the back of the Media Gateway ExpanderInch Rack Mount Kit BayStack 470 Switch BayStack 470 Switch profile Part 1 Property Description BayStack 470 Switch profile Part 2 Property Description Ethernet switch MRV Terminal Server BayStack 460 Layer 2 switchPower over LAN unit 64 of 488 System components MRV IR-8020M Terminal Server profile Property Description Inch rackSystem cables NTVW00AB 66 of 488 System components CS 1000E cables Part 1 NTBK48AA NTTK14AB NTDK95AANTTK34AA NTTK18AB Miscellaneous system components Miscellaneous components Order Code Description Purpose Uninterruptible Power Supply Telephones 72 of 488 Telephones Rack-mounting the components Lifting system components Guidelines for component placement in a rack Weight of CS 1000E system components Component Lbs Rack-mounting a CS 1000E Call Server Items required End of Procedure Procedure Rack-mounting a CS 1000E Call ServerCS 1000E Call Server with installed ear brackets Rack-mounting a Media Gateway or Media Gateway Expander Procedure Removing the cover Unlock the latches Unlock the cover End of Procedure Guide bracket installed in a rack Right ear bracket on a Media Gateway Media Gateway installed in a rack Use two screws on each side to fasten the Media Gateway Signaling Server mounting accessories Rack-mounting a Signaling ServerProcedure Preparing a Signaling Server for rack-mounting Chassis support bracket Left hinge mount Right hinge mount Page Disconnect AC Power Grounding the Rack Installation Main AC Power Disconnect Installed rack-mount bracket Rack-mounting the Signaling Server Rack-mounting a Terminal Server Rack-mounting a BayStack 470 SwitchRack-mounting a BayStack 460 Power over Ethernet unit Installing system grounds Installing a ground bar Follow Procedure 6 to install a ground bar Procedure Installing an NTBK80 Ground Bar Procedure Installing an NTDU6201 Ground Bar Follow Procedure 7 to install an NTDU6201 Ground BarNTBK80 Ground Bar End of Procedure Grounding a Signaling Server Grounding a CS 1000E Call Server 96 of 488 Installing system grounds Installing system grounds Page 97 Grounding a Media Gateway Expander Follow Procedure 10 to ground a Media Gateway ExpanderProcedure Grounding a Media Gateway Expander Installing system grounds Page 99 Grounding other rack-mounted components Grounding multiple pieces of equipment in a rack Grounding equipment in the UK Follow Procedure 11 to ground equipment in the UKProcedure Grounding equipment in the UK 102 of 488 Installing system grounds Standard 4.00 September Connecting CS 1000E system components This section contains information on the following topics Connecting Call Server 0 to Call Server Follow Procedure 12 to connect co-located Call Servers Connecting co-located Call ServersConnecting Campus Redundant Call Servers Procedure Connecting co-located Call Servers Vlan 3 Elan Connecting the CS 1000E Core Call Servers to an MG 1000EProcedure Connecting Campus Redundant Call Servers MG 1000E operation MG 1000E Digital set 100BaseT ports Dual Homed connection Robust Data Network Topology HSP Connecting a Signaling Server to the Elan subnet Procedure Connecting a Signaling Server to the Elan Procedure Connecting a Signaling Server to the Tlan subnet Connecting a Signaling Server to the Tlan subnetSignaling Server Elan subnet and Tlan subnet connectors Tlan Elan Shielded 50-pin to Serial/ELAN/TLAN adapter Tlan RJ-45 Elan RJ-45 Procedure Connecting a Media Card to the Elan subnet Connecting a Media Card to the Elan subnetFollow Procedure 19 to connect a Media Card to the Elan Connecting a Media Card to the Tlan subnet Procedure Connecting a Media Card to the Tlan subnet Connecting a Media Gateway to a Media Gateway Expansion Media Gateway and Media Gateway Expander connections Page Installing software on the CS 1000E Installing the software Procedure Installing the software on the Call Server Installing software on the CS 1000E Page 121 122 of 488 Installing software on the CS 1000E FAT 124 of 488 Installing software on the CS 1000E Installing software on the CS 1000E Page 125 I N M E N U Following keycode files are available on System requests keycode validation Install M E N U Standard 4.00 September Installing software on the CS 1000E Page 131 132 of 488 Installing software on the CS 1000E SDL Installation Menu Standard 4.00 September Continue with database installation Page Install M E N U At this point the system reloads and initializes Verify the installation database Procedure Verifying the installation database Reconfigure I/O ports and call registers Procedure Reconfiguring I/O ports and call registers Procedure Installing the software on the second Call Server Install the software on the second Call ServerProcedure Testing the Call Server Test the Call Server Make the system redundant Procedure Making the system redundantVerifying Call Server 0 is active Stat CPU Get status of CPU and memory Exit the program Stat Health Get status of CPU and memory Exit the program 144 of 488 Installing software on the CS 1000E Installing software on the CS 1000E Page 145 Get status of MG 1000E Ipmg Complete the CP PIV installationCommand parameter none Command parameter core # with values of 0 or Procedure Testing Call Server Test redundancy Stat CPU Get status of CPU and memoryLoad program Test database integrity End of Procedure Testing Call Server Switch call processing from Call ServerProcedure Switching call processing To Call Server Clear the displays on the Call Servers Perform a customer backup data dump installation release Loss of Data Installation is now complete Connecting MG 1000T system components Pstn MG 1000T Media Gateway operation 156 of 488 Connecting MG 1000T system components CS 1000T SSC NTDK57AA 158 of 488 Connecting MG 1000T system components Connecting MG 1000T system components Page 159 MG 1000T Slan subnet cables MG 1000T Core connectors MG 1000T 100BaseT cable connection 10/100 BaseT connectors Connecting an MG 1000T Core to the Elan subnetProcedure Connecting an MG 1000T Core to the Elan subnet 10/100 Procedure Connecting a Signaling Server to the Elan subnet Signaling Server Elan and Tlan network interfaces Connecting MG 1000T system components Page 163 Diagram of the Shielded 50-pin to Serial/ELAN/TLAN adapter Procedure Connecting a Media Card to the Elan Connecting a Media Card to the ElanFollow Procedure 39 to connect a Media Card to the Elan 166 of 488 Connecting MG 1000T system components Connecting MG 1000T system components Page 167 Page Installing and configuring the Signaling Server software Signaling Server Software Install Tool Signaling Server Software CD-ROM Procedure Downloading the Signaling Server CD image End of Procedure Creating a Signaling Server Software CD-ROM Installing the software Procedure Installing the Signaling Server software Upgrade boot sequence CPU PC Pentium Copy IP configuration Install Tool banner screen Nortel Networks First boot of a new system Date and time System Summary System Information Hard disk test Not recently tested Tested within 24 hours Following messages display on the screen Install Tool Main Menu Installation Status Installation Status Summary Installation output Success IP Phone firmware Voice Gateway Media Card loadware Leader/Follower Signaling Server configuration Element Manager System Administration Application configuration Network Routing Service NRS co-resident Signaling Server Network Routing Service NRS stand-alone Signaling Server NRS type co-resident Signaling Server NRS type stand-alone Signaling Server Leader Signaling Server configuration Follower Signaling Server configuration Stand-alone Signaling Server configuration Primary NRS IP address Alternate NRS IP address IP Telephony parameter configuration NRS IP Installation Status Summary New install/upgrade Logging in to the Signaling Server Quit Procedure Logging in to the Signaling Server Verifying a successful configuration Testing the Leader Signaling ServerPage Configuring the CS 1000E Call Server 200 of 488 Configuring the CS 1000E Call Server Procedure Enabling the Login Name option Enabling the Login Name optionFollow Procedure 47 to enable the Login Name option Configuring login IDs and passwords PWD2 Follow Procedure 48 to configure login IDs and passwords Procedure Configuring login IDs and passwords NPW2 MAT YES Enabling the multi-user option Follow Procedure 49 to enable the multi-user optionProcedure Enabling the multi-user option Procedure Configuring pseudo-terminals PTYs Configuring pseudo-terminals PTYsFollow Procedure 50 to configure pseudo-terminals User MTC BUG SCH Checking PTY status Follow Procedure 51 to check the PTY statusProcedure Checking PTY status REQ CHG Configuring Virtual Tone and Conference CircuitsPrompt Response Comment Type Cequ Configuring the MG 1000E Bandwidth Management Zones Procedure Configuring MG 1000E Bandwidth Management Zone LD 117 Bandwidth management zone commands Command Description Slot Configuring the MG 1000E portsType Supl Supt Ipmg Configuring Digitone Receivers Configuring Tone Detectors MFR, MFC, MFE, MFK5, MFK6 units on card Procedure Launching Element Manager Logging in to Element Manager Address field Element Manager login End of Procedure Importing preconfigured IP telephony files Procedure Importing an existing node Click Import Node Files on the Node Summary web Select Configuration IP Telephony from the navigatorImport Node Files Retrieve and upgrade configuration files Performing a datadump Adding a Follower Signaling Server to an IP telephony nodeProcedure Performing a datadump using Element Manager Call Server Backup and Restore web CS 1000E Backup Page NTDK20HA Configuring a Small System ControllerSmall System Controller profile Part 1 Property Description NTDK99AA Adding a software daughterboard and remote security deviceSmall System Controller profile Part 2 Property Description NTDK83AA Adding a 100BaseT daughterboard dual port 100Baset daughterboard dual port LED cable connector 229 SSC with two 100BaseT Daughterboards dual port Adding a 100BaseT daughterboard single port 100BaseT daughterboard single port NTDK99Page NTDK57DA Bulkhead connector on a Media Gateway Installing software on an MG 1000E Small System Controller PC card interface Installing software on an MG 1000E SSC Procedure Installing software on an MG 1000E SSC Software Installation Program Configure the IP Enter y System response Copying new Psdl Copying loadware files System then reboots Page Installing software on an MG 1000T Small System Controller Software Installation Program Feature set and licenses AUX ID Customer database Keycodes Keycode rejection Installing software on an SSC Procedure Installing software on an SSC Power connectors Software Installation Program Layer-2 configuration System response Communication Server 1000 Software Rls 4.5 will be installed Setting the system time and date Procedure Setting system time and date Ttad Page Connecting a Terminal Server 254 of 488 Connecting a Terminal Server Configuring a Terminal Server DCD DTR DSR RXD TXD Procedure Connecting a Terminal Server to the systemStart Programs Accessories Communication HyperTerminal.exe DTR DSR/DCD GND Configuring the Terminal Server IP address Procedure Configure IP address for the Terminal Server Procedure Run telnet from PC Use Start Run Telnet Terminal Server virtual management port Telnet CS 1000E COM port from a PC Start Run Configuring a transparent rlogin port Procedure Configuring a transparent rlogin port Zmodem requirements Feature Setting Where Xx = port number Standard 4.00 September Configuring a transparent rlogin port with sample data Define Port 2 Autodedicated Enabled Accessing an MRV Console Port through the on-board modem CS 1000E COM port types System components and COM port typePage Configuring a terminal and SDI ports Setting the TTY terminal port Traditional terminal SDI connection Configuring a terminal and SDI ports 269 VT220 setup values CS 1000E Core Call Server SDI connection Parity none Flow control none MG 1000E SDI connectionMG 1000T SDI connection Controlling the baud rate MTC/SCH/BUG Procedure Connecting SDI ports on the Media Gateways SDI port access to the Media Gateway SSC card Signaling Server SDI connection Media Card SDI connection Maintenance to Signaling Server connectionBayStack 470 SDI connection Configuring a terminal and SDI ports Page 275 Page Verifying the network Procedure Checking the status of the Elan network interfaces Checking the status of the Elan network interfaces SSC card Elan LED location Stat Elnk Stat Host Ping Checking the status of the HSP ports HSP Link Carrier OK Checking the status of the MG 1000T 100BaseT links SSC 100BaseT daughterboard link LED location SSC 100BaseT daughterboard dual port LEDs Media Gateways SSC faceplate Port LEDs Stat IPL Ping 192.168.0.11 Successful Procedure Check CS 1000E did calls from MG 1000T To check trunking on the MG 1000T follow Procedure 73 onProcedure Checking the status of the MG 1000T trunks Checking MG 1000T trunking functionality 288 of 488 Verifying the network Standard 4.00 September Installing and cross-connecting a trunk card Circuit card assignments in the Media Gateway Circuit card assignments in the Media Gateway Expander 292 of 488 Installing and cross-connecting a trunk card NTBK50 2.0 Mbit BRI Circuit card optionsDigital trunk cards Antistatic wrist strap Procedure Connecting a trunk Connecting a trunkFollow Procedure 75 to connect a trunk NTRB21 Tmdi 1.5 Mbit DTI/PRI Universal Trunk card connections OFF BK-BL NT8D14 Universal Trunk connections Part 1BL-W BR-W BL-BK NT8D14 Universal Trunk connections Part 2 Lists the connections required by the E&M Trunk card NT8D15 Paging Type Equipment Unit Mode Pair Color DesignationsTrunk card connections NT8D15 E&M Trunk card Part 1 Cables Card 1 through BL-Y Escg NT8D15 E&M Trunk card Part 2 Cables Card 1 throughBK-O ESC Sigb BR-W Siga Pair Color Unit Pins Lead DesignationsTrunk connections Europe Sigb Siga BK-O Sigb Siga BK-BR BR-BK BL-Y BL-W 2-wire Type 2 Part 2BK-BL BL-BK BK-O BK-BR BR-BK BK-S BL-Y BK-BL BL-BK SIG1B BL-W SIG0A BR-W SIG0BSIG1A BK-O SIG2A BL-W BL-R SIG3ABL-Y SIG3B BL-W SIG B SIG a BR-W 2280 Hz TIE Trunk connections Part 2BR-R BK-G SIG B BK-O SIG a BK-G BL-Y PPM2 BL-W PPM0PPM1 BR-W BK-O PPM5 PPM3PPM4 BK-BR PPM6 309 Trunk connections UK BL-W BR-W BL-R BR-R BK-BL BL-BK BK-O BK-G BK-BR BR-BK BK-S BL-Y BL-W BR-W BL-R BR-R BK-BL BL-BK BK-O BK-G BK-BR BR-BK BK-S BL-Y NT5K19 2W paging mode terminations Pair Pins Pair color Unit BR-W BL-R BK-O BK-BR BR-BK BL-Y BL-R BK-BL BL-BK BK-BR BR-BK BK-S NT5K19 4W Type 1 mode terminations Pair Pins Pair color Unit BL-W BL-R BR-R BK-BL BL-BK BK-G BK-BR BR-BK BK-S NT5K19 AC15 mode pair terminations Pair Pins Pair color Unit BL-W BL-R BR-R BK-G BK-BR BR-BK Verifying trunk functionality BL-W SIG B SIG a BR-W BR-R BK-O BK-G BL-Y Installing and configuring a Voice Gateway Media Card Introduction Configuring a card Adding a card to an IP telephony node Node Configuration web Edit web Cards Configuring a card as a node Leader Configuring voice gateway channels using Element Manager VGW Channel web Add VGW channels Configuring voice gateway channels using LD VGW channels list End of Procedure Type VGW Procedure Configuring voice gateway channels using LDREQ DES Iptn YES Saving configuration changesMaxu Zone Installing a CompactFlash CompactFlash card location CompactFlash card and Retaining Pin Position the CompactFlash in socket Procedure Installing the CompactFlashCompactFlash socket on Voice Gateway Media Card Insert CompactFlash to extend Eject button Retaining Pin hole Retaining Pin fully inserted End of Procedure Inserting the Retaining Pin Installing a card in a Media Gateway Media Gateway card slot location Media Gateway Expander card slot location TN assignments for MG 1000E MG 1000E Expander Slots Media Gateway Verifying a card Node Maintenance and Reports web Node Maintenance and Reports expanded node General Commands VgwShowAll result Maintenance by Overlay web Select Select by Functionality Communication Server 1000E Installation and Configuration Network & Peripheral Diagnostics web Select System Maintenance from the navigator Disabling a card Disabling a card unit Enabling a card Enabling a card unit Verifying functionality Upgrading loadwarePage Installing the Main Distribution Frame Terminal block requirements Installing a BIX cross-connect terminalProcedure Installing a BIX cross-connect terminal Typical BIX cross-connect terminal layout Installing a Krone Test Jack Frame for the UK Pair cable on three Krone strips Procedure Installing the Krone Test Jack Frame UK Other equipment Media Gateway Expansion Typical Krone cross-connect terminal layout UK Connecting the cables to the Media Gateways Procedure Connecting the cables to the Media Gateways Cable connectors at the back of the Media Gateway Cable connectors at the back of the Media Gateway Expander AUX cable connector Pfts Page Configuring an IP telephony node Before you begin Perform a datadump Configuring MS Internet Explorer Procedure Turning off browser caching in Internet Explorer Internet Explorer Internet Options Temporary Internet files Settings window Follow Procedure 93 to log in to Element Manager Procedure Logging in to Element Manager Configuring an IP telephony node Page 371 372 of 488 Configuring an IP telephony node Click Import Node Files Import Node Files web Click Import Click Save and Transfer Transfer Progress Starting Transfer Progress Transferring Transfer Progress Complete Transfer / Status web Adding a Follower Signaling Server to an IP telephony node Performing a datadump Configuring an IP telephony node Page 381 Page Installing Line cards and cross-connecting telephones Standard 4.00 September Circuit card assignments in a Media Gateway Circuit card assignments in a Media Gateway Expander Procedure Cross-connecting telephones Cross-connecting telephonesCircuit cards features Connect the telephones according to on page 387 and on NE-500/2500-type telephone cross connections Connecting a telephone without a Pftu Digital telephone cross connections Connecting an off-premise telephone Procedure Connecting a telephone without a Pftu Procedure Connecting an off-premise telephone NTAK92BA Off-Premise Protection Module connections Connecting an attendant consoleProcedure Connecting an attendant console Attendant console connections Unit Color Unit End of ProcedureColor combinations of cable pairs BK-BL BK-O BK-G BK-BR BK-SPage Installing and configuring IP Phones Installing and configuring IP Phones Page 396 Package components for the IP Phones Replacement partsIP Phone 2001/2002/2004 Power Adapters Lists the IP Phone 2002 package components and product codes IP Phone 2001 components list Part 2 NTDU92AA16 IP Phone 2001/2002/2004 Power AdaptorsIP Phone 2002 components list Part 2 IP Phone 2004 Power Adaptors IP Phone 2004 component list Part 2 NTDU96AB70 IP Phone 2007 power adapterIP Phone 2007 power cords IP Phone 2007 component list Part 2 IP Audio Conference Phone 2033 components list Lists the Package components for the Wlan Handsets Wlan Handset component list Part 1 Wlan Handset component list Part 2 Wlan Handset component list Part 3 Wlan Handset component list Part 4 UK-HK Connectivity and power requirements Installation and configuration procedures Configuring VoIP bandwidth management zones NEW Zone Established inside, from, or toward this zone LD 97 Configure a Virtual Superloop Prompt Response Comment Configuring virtual superloopsProcedure Configuring virtual superloops MG 1000T virtual superloop/virtual card mapping Configuring an IP Phone using LDProcedure Configuring the IP Phones Card CLS ADD REQ NEW CHGType KEY Installing and configuring IP Phones Page 414 Installing and configuring IP Phones Page 415 CFW, NUL MWK, NULTRN, NUL RGA, NUL CHG, NUL CPN, NUL General Commands Node Password Procedure Installing IP Phone hardware components Installing IP Phone hardware componentsNode Temp Password IP Phone 2004 components Page IP Phone connections End of Procedure Configuring the IP Phone boot parameters Entering IP Phone boot parameters using manual configuration Enter the Server 1 IP node IP. The IP Phone prompts Go to on Press the OK key. The IP Phone prompts Entering IP Phone boot parameters using full Dhcp parameters Go to step Enter the Vlan ID. The IP Phone displays End of Procedure Enter the 1 to use Partial DHCP. The IP Phone prompts After several seconds, the IP Phone prompts Using Set-Based Installation Procedure Using Set-Based Installation 434 of 488 Installing and configuring IP Phones Installing the IP Softphone OK, EXTENSION? REQ NEW Installing and configuring on the PCProcedure Configuring the IP Softphone FDN Procedure Installing the IP Softphone 2050 on your PC Installing the IP Softphone 2050 applicationProcedure Installing the USB Headset Kit Running the IP Softphone 2050 for the first time Select Start Programs Nortel IP Softphone Upgrading firmware Verifying IP Phone functionalityDisplaying registered IP Phones Select System Status IP Telephony from the navigatorPage Installing and cross-connecting a Power Fail Transfer Unit Installing and connecting a QUA6 Pftu Procedure Installing and connecting a QUA6 Pftu AUX cable connectors on media gateway NTAK1104 ALM Pftu Power fail transfer Brtn Ground Installing and connecting a third-party PftuPftu control lead signals Lead State Pfts Open Ground Connecting an analog 500/2500-type telephone to a Pftu Analog Line card cable distribution PFT BR-BK PFT BR-Y Procedure Connecting a Trunk to a Pftu Connecting a trunk to a PftuFollow Procedure 117 to connect a Trunk to a Pftu BL-V Telephone Telephone Line card TN assigned to the telephone 17T Telephone 460 Type CDB Installing an alarm using an alarm port assigned in LDLD 15 Assign an alarm port Prompt Response Comment Installing an alarm through QUA6 Pftu connections AC capacities Maximum Contacts in Pftu Makes with 10T Opens 10T and 10R Makes with 22T Opens 22T and 22R 476 MG 1000T switch over to Survival Mode Automatic Switchover to Survival Mode Manual Switchover to Survival Mode Switchback from Survival Mode Automatic Switchback from Survival Mode Lock and Unlock commands Switchover Timer Database synchronization Where Cab# = specified Survivable Media GatewayDWL Download command is available in LD SWP command DAT command SWP command operation SWP command operation RES command operation RES command RIB command operation RIB command Configuring a survivable MG 1000T Expansion Procedure Configuring a survivable MG 1000T Expansion Where Configuring Alternate primary controllerPrinting Survivable MG 1000T Expansion parameters Click LAN configuration Verifying IP telephony node operation in Survival Mode Procedure Retrieving CDR files using XModem Retrieving CDR records from a survivable MG 1000T Expansion Basic system telephony configuration Basic system configuration Flow charts Procedure Configuring the basic system Data-entry-sequence for new systems Configuration Record Data Block MG 1000T card slot assignment TN assignment Shows the TN assignments for the MG 1000EPage Implementation summary Standard 4.00 September 487 Page Page Installation and Configuration Communication Server 1000E