RX Speed Reference Setpoint #1 (%), 97

RX Speed Reference Setpoint #1 (frequency), 97 RX Speed Reference Setpoint #2 (%), 98

RX Speed Reference Setpoint #2 (frequency), 98 RX Torque Reference Setpoint #1 (%), 98

RX Torque Reference Setpoint #2 (%), 98 RX2 Bias Adjust, 137

RX2 Gain Adjust, 137

RX2 Speed Reference Setpoint #1 (%), 99

RX2 Speed Reference Setpoint #1 (frequency), 99 RX2 Speed Reference Setpoint #2 (%), 100

RX2 Speed Reference Setpoint #2 (frequency), 100 RX2 Torque Reference Setpoint #1 (%), 100 RX2 Torque Reference Setpoint #2 (%), 100

S

S1, 22, 23

S1 – S4 Input Terminal Delay, 82

S1 Input Terminal Assignment, 72

S2, 22, 23

S2 Input Terminal Assignment, 72

S3, 22, 23

S3 Input Terminal Assignment, 72

S4, 22, 23

S4 Input Terminal Assignment, 73

S5 – S16 Input Terminal Delay, 82

S5 Input Terminal Assignment, 73

S6 Input Terminal Assignment, 73

S7 Input Terminal Assignment, 74

Scrolling Monitor, 43

Scrolling Monitor Select, 57

Service Life Information, 9

Shipping Weight, 182

Shipping Weight (lbs.), 182

Short Circuit Detect Pulse, 52

Short Circuit Test, 156

Short Circuit Test Duration, 156

Sink/Source Setting Error, 179

Soft Stall, 65

Soft Stall Enable, 52

Soft Start, 52

Spare Parts Listing, 201

S-pattern 1, 141

S-pattern 2, 141

S-Pattern Lower Limit Adjustment, 142

S-Pattern Upper Limit Adjustment, 142

Special Control Parameters, 57, 58

Special Parameters, 58

Speed at Drooping Gain 0%, 116

Speed at Drooping Gain 100%, 116

Speed Drop Detection Frequency Range, 158

Speed Limit (torque) Reference, 132

Speed Limit Torque Level, 132

Speed Limit Torque Range, 132 Speed Limit Torque Recovery, 132 Speed Loop Integral Gain, 124 Speed Loop Parameter Ratio, 124 Speed Loop Proportional Gain, 124 Speed Reach Frequency, 68

Speed Reach Frequency Tolerance, 68 Speed Ref. Setpoint, 50

Speeds, 54

splash screen display, 27 ST, 22, 23

ST Input Terminal Assignment, 72 ST Input Terminal Delay, 82

ST Signal Selection, 69 ST1, 17

Stall, 51

Stall Cooperation Gain at Field Weakening Zone, 138 Stall Prevention During Regeneration, 135 Standard Mode Settings, 47

Startup and Test, 21 Startup Frequency, 104 Startup Wizard, 47

Startup Wizard Requirements, 40 Status LED, 36

Stop Key, 36 Stop Pattern, 165 SW1, 25 SW2, 25

Switching Frequency of Current/Voltage Control, 139 Switching Load Torque During Forward-Run, 118 Switching Load Torque During Reverse-Run, 119 Synchronized Torque Bias Input, 130

System Grounding, 19

System Integration Precautions, 7 System Operation, 38

T

T1/U, 19

T2/V, 19

T3/W, 19

Tension, 130

Tension Torque Bias Input, 130

Terminal Descriptions, 23

Terminal Selection Parameters, 49

Torque Boost Adjustment, 162

Torque Command, 129

Torque Command Filter, 129

Torque Command Mode, 132

Torque Control, 52, 53

Torque Limit Group, 166

Torque Limit Mode, 134

214

G7 ASD Operation Manual

Page 220
Image 220
Toshiba G7 manual 214