Toshiba G7 manual Preset Speed #1, Preset Speed #2

F018							F019
Preset Speed #1	Direct Access Number —					F018
Program ⇒ Pattern Run Control ⇒ Preset Speeds ⇒ 1	Parameter Type — Numerical
Up to 15 output frequency values that fall within the Lower Limit and the	Factory Default — 0.0
Upper Limit range may be programmed into the drive and output as a Preset	Changeable During Run — Yes
Speed. This parameter assigns an output frequency to binary number 0001 and	Minimum — Lower Limit (F013)
is identified as Preset Speed #1. The binary number is applied to S1 – S4 of the
	Maximum — Upper Limit (F012)
Control Terminal Strip to output the Preset Speed.
Perform the following setup to allow the system to receive Preset Speed	Units — Hz
control input at the S1 – S4 terminals:
1. Program ⇒ Fundamental Parameters ⇒ Standard Mode Selection ⇒ Use	Preset	S4	S3	S2		S1	Output
		MSB			LSB
Control Terminal Strip.
	1	0	0	0		1	F018
2. Program ⇒ Terminal Selection Parameters ⇒ Input Terminals ⇒ S1 (set to
	2	0	0	1		0	F019
Preset Speed Command 1; LSB of 4-bit count). Repeat for S2 – S4 (MSB
	3	0	0	1		1	F020
of 4-bit count) as Preset Speed Command 2 – 4, respectively (all
	4	0	1	0		0	F021
Normally Open).
	5	0	1	0		1	F022
Note: The default setting of S4 is EOff, but this terminal may be re-	6	0	1	1		0	F023
assigned as the MSB.	7	0	1	1		1	F024
3. Program ⇒ Frequency Setting Parameters ⇒ Preset Speeds ⇒ 1 (press	8	1	0	0		0	F287
	9	1	0	0		1	F288
Enter twice and set an output frequency as Preset Speed #1; repeat for
	10	1	0	1		0	F289
Preset Speeds 2 – 15 as required).
	11	1	0	1		1	F290
4. Program ⇒ Frequency Setting Parameters ⇒ Preset Speed Mode ⇒ Use	12	1	1	0		0	F291
Speed Modes (Enable/Disable).	13	1	1	0		1	F292
When Enabled, the direction, accel/decel, and torque settings of the	14	1	1	1		0	F293
	15	1	1	1		1	F294
Preset Speed being run are used.
	Note: 1 = Terminal connected to CC.
When Disabled, only the speed setting of the Preset Speed being run is
used.
5. Place the system in the Remote mode (LocalRemote LED Off).
6. Provide a Run command (connect F and/or R to CC).
Connect S1 to CC to run Preset Speed #1 (S1 to CC = 0001 binary).
With S1 – S4 configured to output Preset Speeds (F115 – F118), 0001 – 1111
may be applied to S1 – S4 of the Control Terminal Strip to run the associated
Preset Speed. If bidirectional operation is required, F and R must be connected
to CC, and Use Speed Modes must be enabled at F380.
With S1 being the least significant bit of a binary count, the S1 – S4 settings
will produce the programmed speed settings as indicated below.
Preset Speeds are also used in the Pattern Run mode.
Preset Speed #2	Direct Access Number —					F019
Program ⇒ Pattern Run Control ⇒ Preset Speeds ⇒ 2	Parameter Type — Numerical
This parameter assigns an output frequency to binary number 0010 and is	Factory Default — 0.0
	Changeable During Run — Yes
identified as Preset Speed #2. The binary number is applied to S1 – S4 of the
	Minimum — Lower Limit (F013)
Control Terminal Strip to output the Preset Speed (see F018 for further
information on this parameter).	Maximum — Upper Limit (F012)

Units — Hz

66 G7 ASD Operation Manual