Patton electronic SmartNode 4110 Series manual 637

SmartWare Software Configuration Guide					52 • VoIP debugging
01:00:10	H323	> [EP	h323-00c07230]	Display:	50
01:00:10	H323	> [EP	h323-00c07230]	User-User:

01:00:10 H323 > [EP h323-00c07230] Set state to TERMINAL TRYING

01:00:10 H323 > [EP h323-00c07230] State: TERMINAL TRYING, Call Event: PEER CON-

NECTED

01:00:10 H323 > [EP h323-00c07230] State: TERMINAL TRYING, Call Event: PROGRESS

01:00:10 HRAS > Stack: Received Admission Confirm

01:00:10 H323 > [EP h323-00c07230] Stack: State: DIALTONE 01:00:10 H323 > [EP h323-00c07230] Call-ID is 0213:4d8d:13ba:1db8:2eef:0030:2b00:1e0e

01:00:11 H323 > [EP h323-00c07230] Stack: Received Incomplete-Address Indication

01:00:11 H323 > [EP h323-00c07230] Stack: State: RINGBACK

01:00:11 H323 > [EP h323-00c07230] Stack: Received ALERTING

01:00:11 H323 > [EP h323-00c07230] Progress Indicator: (none)

01:00:11 H323 > [EP h323-00c07230] State: TERMINAL TRYING, Call Event: TERMINAL ALERTING

01:00:11 H323 > [EP h323-00c07230] Set state to TERMINAL ALERTING 01:00:14 H323 > [EP h323-00c07230] Stack: State: CONNECTED (CALL-SETUP)

01:00:14 H323 > [EP h323-00c07230] State: TERMINAL ALERTING, Call Event: TERMINAL CONNECTED

01:00:14 H323 > [EP h323-00c07230] Set state to CONNECTED 01:00:14 H323 > [EP h323-00c07230] Stack: Send STATUS INQUIRY

01:00:14 H323 > [EP h323-00c07230] Stack: Opening the H.245 control-channel

01:00:14 H323 > [EP h323-00c07230] State: CONNECTED, Call Event: PROGRESS

01:00:14 H323 > [EP h323-00c07230] Stack: Received STATUS. Audit successful

01:00:14 H323 > [EP h323-00c07230] Channel State: IDLE, Channel Event: CONTROL-UP 01:00:14 H323 > [EP h323-00c07230] Set channel state to OPENING

01:00:14 H323 > [EP h323-00c07230] State: CONNECTED, Call Event: PROGRESS

01:00:14 H323 > [EP h323-00c07230] Stack: State: CONNECTED (CALL)

01:00:14 H323 > [EP h323-00c07230] Stack: New Incoming Logical Channel: 00bccd68

01:00:14 H323 > [EP h323-00c07230] Channel State: OPENING, Channel Event: MODE-UP 01:00:14 H323 > [EP h323-00c07230] Set channel state to UP

Explanation:

•First the state of the gateway is checked. The state is UP, and the RAS engine is REGISTERED, which is OK.

•The line 01:00:10 H323 > [EP h323-00c07230] Stack: Allocated new call: 0x00be5968 tells that there is a new call incoming from H.323. This means that transport layer is OK. If there is no debug output at all, try to use debug gateway h323 tpktchan, which monitors all H.323 socket TCP traffic.

•The line 01:00:10 H323 > [EP h323-00c07230] Destination Address: TEL:60,60 and below show the calling and called party properties. In the present case, the called party number is 60.

•00:29:03 HRAS > Stack: Received Admission Confirm says that the gatekeeper allowed us to dial to H.323 network with the given call parameters. If you can’t see any H.323 SETUP message on the net, or if the called gateway does not indicate any H.323 message received, use debug gateway h323 tpktchan to verify that a packet is being sent.

Debugging call signaling 637