Manuals / Omron / Computer Equipment / Network Card

Omron CJ1W-CLK21-V1, CVM1-CLK21, CS1W-RPT01, C200HW-CLK21 Other Status, Refer to 7-4 Setting Rout

Models: CS1W-RPT01 CJ1W-CLK21-V1 CVM1-CLK21 CQM1H-CLK21 CS1W-CLK21-V1 C200HW-CLK21

1 401

Download 401 pages 33.98 Kb

Page 320

Status Area and Troubleshooting			Section 9-2
Other Status

	Bit status	Probable cause	Probable remedy

	Error log exists (CIO 1500	Error information on the	Using the Controller Link
	+ 25 ⋅ n, bit 15) is 1: ON	Controller Link Unit (an	Support Software or an
		error log) has been	FINS command, read the
		recorded.	cause of the current error.
			Alternatively, use past error
			log records to troubleshoot
			the problem.

	Communications controller	The Controller Link Unit is	Replace the Controller Link
	send error (CIO 1500 + 25	faulty.	Unit.
	⋅ n, bit 11) is 1: ON

	Inconsistent network	Indicates that the network	Check the network param-
	parameters (CIO 1500 +	parameters recorded in the	eters on the Network in
	25 ⋅ n, bit 10) is 1: ON	CS/CJ Bus Unit Area differ	use using the Controller
		from the values of the Net-	Link Support Software, and
		work in use.	reset necessary parame-
			ters.

	Node address duplicate	The same node address	Reset so that each node
	setting error (CIO 1500 +	has been used more than	address is used only once
	25 ⋅ n, bit 9) is 1: ON	once.	within the same Network.

	EEPROM error (CIO 1500	An error has occurred	Check the status of bits 00
	+ 25 ⋅ n, bit 7) is 1: ON	while writing data to the	to 02 in (CIO 1500 + 25 ⋅
		CPU Unit’s EEPROM.	n, and correct any prob-
			lems found. If the error
			occurs again, replace the
			CPU Unit.

	PLC system setting error	The CPU Unit’s EEPROM	Check the status of bits 00
	(CIO 1500 + 25 ⋅ n, bit 3)	data is damaged.	to 02 in (CIO 1500 + 25 ⋅
	is 1: ON		n, and correct any prob-
			lems found. If the error
			occurs again, replace the
			CPU Unit.

		The PLC is protected.	Set the PLC’s protect
			switch to OFF.

	Routing table error	The routing table data	Refer to 7-4 Setting Rout-
	(CIO 1500 + 25 ⋅ n, bit 2)	within the CPU Unit’s	ing Tables and reset the
	is 1: ON	EEPROM is damaged.	routing tables correctly. If
			the error occurs again,
			replace the Controller Link
			Unit.

		There is an error in the	When using a routing
		routing table setting.	table, refer to 7-4 Setting
			Routing Tables and reset
			the routing tables correctly.
			If no routing tables are
			being used, delete the
			tables.

297

Image 320

Omron CJ1W-CLK21-V1, CVM1-CLK21, CS1W-RPT01, C200HW-CLK21, CQM1H-CLK21, CS1W-CLK21-V1 Other Status, Refer to 7-4 Setting Rout

Contents

Controller Link Units Controller Link Units Page Omron Product References  Omron Confirming Unit Versions with Support Software Unit VersionsUnit Version Notation on Products Using the Unit Version Labels Unit Version NotationFunction Support by Unit Version Unit Versions and Manufacturing Dates/Lot Numbers Viii Table of Contents Data Links 105 Appendices Xii Name Contents Cat. No Suffixes omitted About this Manual Xiv Read and Understand this Manual Application Considerations Disclaimers Xviii Precautions Intended Audience General PrecautionsSafety Precautions Operating Environment Precautions Operating Environment Precautions Applications Precautions Xxiii Low Voltage Directive Conformance to EC DirectivesEMC Directives Section What Is the Controller Link? Wired SystemOverview Section Converting Part of the Transmission Line to Optical Fiber Branch WiringLong-distance Wiring Token Ring Mode CS1W-CLK12-V1 CVM1-CLK12 Token Bus Mode Connecting Repeater Units Using GI Optical Fiber Cable Message Service Automatic SettingManual Setting Data Links Status Area Error LogOr the message service function Features Features of Twisted-pair CableFeatures of Optical Fiber Cable Specifications Flexible Inter-network Connections Compatible with Different Node ConfigurationsImproved Error Handling Features and Functions of Version-1 Models Total length of wired networks can be extendedDevices can be modularized Up to 62 nodes can be connected Specifications and Configurations System Configuration Branch Wiring General Specifications Maximum Configuration of 62 Nodes Communications Specifications Items Specifications Within 1 segment See Entire network PCF type GI type Wired System Controller Link Unit Models and PLCs External Appearance Installation Tables WeightMax No. Units per PLC Name Model Current consumption Number Per Unit a Units CS/CJ-series Controller Link Unit ModelsUnit Ver .2 Pre-Ver .2 Without -V1 suffix Suffix Communications Cables Repeater Units when RequiredDevices for Connection Relay Terminal Blocks Name Model Remarks Programming External Model Applicable PLCs Device Programming DevicesProgramming Device for the PLC Using an Independent Computer Controller Link Support Software Version Software External Model Applicable PLCs Remarks EV2 HG/HE, CVM1 Controller Link Support Software Menu Overview CX-Programmer When Operating on Personal Computer as Peripheral Software When Operating on Personal Computer Connected as a NodeSelection of Communications Functions Software External Model Applicable PLCs CVM1, CV-series, and CS/CJ-series PLCs Basic ProceduresPreparations C200HX/HG/HE and CQM1H-series PLCs Application Precautions Communications error type Data link areas C200HX/HG/HE PLC Section Section Basic Procedures Data Links Procedures Manually Setting Data Links Set the data link mode Automatically Setting Data Links Start the data linksCS/CJ Series Word 0 of DM30000 + 100 ⋅ AR 0700 operating level #0 CV-series PLCs Console Only Gramming Console Section To 1 Type CX-Programmer version 3.2 or higher Chain Type CS/CJ Series Word 0 of DM30000 + 100 ⋅ N Message Service Procedure Register routing tables if using inter-network connectionsContents Remarks Create the I/O tables Create the user program Section Installation and Wiring Component Names and Functions CS-series Controller Link Units Wired Unit Indicators Name Color Status Meaning Dimensions Unit mm CJ-series Controller Link Units For details, refer to 9-1 Troubleshooting Using Indicators Component Names and Functions Node address switches Refer to p 3 C200HX/HG/HE Controller Link Unit Yellow Lit Data reception Receive Not lit No data reception Unit number switches Refer to p 4 CVM1 and CV-series Controller Link Unit 34.5 5 CQM1H-series Controller Link Unit Wire-to-Wire Repeater Unit Repeater Unit Indicators Dimensions Unit mm Wire-to-Optical H-PCF Repeater Unit Wire-to-Optical GI Repeater Unit Unit Installation Installing One Controller Link Unit Installing Two Controller Link UnitsMounting Controller Link Units C200HX/HG/HE PLCs CVM1 and CV-series PLCs Installing with Another Communications UnitInstalling with a PC Card Unit CS-series PLCs Expansion CPU Rack CPU Rack CJ-series PLCs CQM1H-series PLCs Mum current of 4.6 a 5 V and maximum power of 30 WMounting a Repeater Unit DIN Track Screw-mounting a Repeater UnitMounting a Repeater Unit on DIN Track Wiring Communications CablesCommunications Cables End Plate PFP-M 2 Plates required per Repeater Unit Not Unit a Relay Terminal Block Connecting the Shield LineTerminal Block Connections Connecting the Communications Cables Using a Relay Terminal Block Apply vinyl tape or a heat-shrinking tube Do not pull on a communication cable Repeater Units Power Supply WiringMark Signal name Line color Power Supply Specifications Laying Optical Cable CS1W-RPT02/03 Only Mounting bracket Tension member Terminal Name Specifications Model Name Model SpecificationsOptical Bus or Optical Ring System H-PCF Cable Optical Fiber Cables Indoor Use Only Optical Fiber Cables with Connectors Indoor Use Only Optical Fiber Cable AccessoriesSpecifications Length Model Name Model Specifications Manufacturer CS1W-RPT03 GI Minimum Standard Maximum Unit Conditions Optical Fiber Cables50/125 ∝m AGF Cable 62.5/125 ∝m AGF Cable ConnectorsConstructing Networks with Repeater Units Specifications within Remarks Each segment Segments Examples of Correct Repeater Unit Connections Branch Wiring 2-stage Repeater Unit ConnectionNumber of Repeater Units Long-distance Wiring 2-stage Repeater Unit Connection Examples of Incorrect Repeater Unit ConnectionsPartial Optical Conversion 2-stage Repeater Unit Connection More than 2 Stages of Repeater Units Terminating Resistance Branch WiringLong-distance Wiring Partial Conversion to Optical Fiber Section Preparations for Communications Unit Number CS-series Controller Link UnitsOverview Node Addresses Pins Baud rate Maximum Transmission distance Baud Rates CJ-series Controller Link Units Default setting is 2 Mbps, 500 mBottom switch Terminating resistance Setting range Nodes To F default is Setting range Nodes 01 to 32 default is Node Baud Rates C200HX/HG/HE Controller Link Units C200HX/HG/HE PLC Operating Level Baud Rate and Operating LevelAlways leave pin 3 OFF Baud Rate Pins 1 Setting the OperatingBaud Rates and Operating Levels Level Pin Pin Operating level Node Setting Baud Rates Always keep pins 3 and 4 set to OFFCVM1 and CV-series Controller Link Units Node Addresses Unit Switch at the front Terminating resistance Set the following pins for the baud rate setting DIP switchSwitch Baud rate Maximum Transmission distance Pin Setting Baud Rate Switch Terminating Nodes ResistanceCQM1H-series Controller Link Units Pin Sion dis Tance 101 Repeater Units Wire-to-Wire Repeater Unit Wire-to RepeaterTerminating Resistance Switch for SL1 Terminating Resistance Switch for SL2 Switch Terminating resistance Data Links CS/CJ-series Controller Link Unit Functions by Unit Version Manually Setting Data LinksWhat Are Data Links? Easy Setting Offsets Automatically Setting Data Links with Equality Layout Automatic Setting Data Links with 1N Allocations Type Model Using Offsets Offsetting Image Description Data Link SpecificationsCommunications error type Data link area Differences between Manual and Automatic Setting Manual setting Automatic setting Setting Data Links Selecting Manual or Automatic Setting Manual Setting Transferring from a Programming Device Data Link Table Specifications Setting item Setting rangeTransferring from a Computer Node CS/CJ-series PLCs 116 C200HX/HG/HE PLCs 118 CVM1 and CV-series PLCs Used. Refer to 5-4 Checking Data Link Status for details CQM1H-series PLCs 121 Precautions Data link start word 1 + Total number of send/receiveWords in area ≤ 247 IR Area W307 for information on the Controller Link Support Board Manual Setting Examples Device Information SettingsSAMPLE1.CLK Same Allocation to All Nodes Data Link Area Structure 124 Device Information Setting SAMPLE2.CLK Different Allocations to Each Node SAMPLE3.CLK Creating Data Link Groups within a Network Device Information Setting Data Link Tables SAMPLE4.CLK Receiving Only Part of Send Data and Offsets Only area 2 is used in this example Automatic Setting Automatic Setting, Equality Layout CS/CJ-series Startup Node Between master and slave nodes Automatic Setting, 1NAllocations Setting Range for Automatic Setting Equality Layout 133 Features of Common Type 1N Allocation 1N Allocation, Common Type 135 136 137 Features of 1 to 1 Type 1N Allocation 1N Allocations, 1 to 1 Type 139 140 Features of Chain Type 1N Allocation 1N Allocation, Chain Type 142 143 144 Settings C200HX/HG/HE Startup Node 146 CVM1 or CV-series Startup Node 148 149 CQM1H-series Startup Node Automatic Setting Example Settings for Equality LayoutLink areas that are created as a result DM Parameter Area DM Parameter Setting Example for 1N Allocation, Common Type Data Link Areas Created Starting and Stopping Data Links Data Link AreasManually Set Data Links Automatically Set Data Links C200HX/HG/HE Start Bit Using a Programming Device or the User ProgramCS/CJ-series Start Bit Using Fins Commands LED Indicators Check the Link and M/A indicators on the front of the unitName Color Status Contents Checking Data Link Status 157 Following shows an example of a remaining receive area Name Function Only status for nodes 1 to 6 are saved Data Link Status Storage Format CS/CJ Series OnlyData link status storage area is set as follows Checking by Manipulating Bit/Word Status Matic settingsSpecification Processing Data Only when Data Links Are Operating Normally Error Detection Program ExampleProgramming Examples for Processing Data when Errors Occur Writing 0000 in the Data Link Area when Errors Occur Data Link Example Communications Error at Node 164 Message Service Introduction Send and Recv CS/CJ-series PLCs 168 C200HX/HG/HE PLCs @SEND90 170 171 Timer/counters numbers 0 to 2047 can send and receive data CIO Section CVM1 and CV-series PLCs Word for data reception at the destination node, N 174 CQM1H-series PLCs 176 177 178 179 180 181 Beginning word for storing response data Cmnd Example Commands for CVM1, CV-series and CS/CJ-series PLCs Type of command Code Send/Receive Data Areas Area Range Area Range CV500, CVM1-CPU01 CVM1-CPU11/21 Selecting Communications Instructions Com TentsPuter Or CV Read/write Message Service Specifications SEND/RECV Flags Using the Message ServiceName Address Contents Word Bit Name Operating Address Contents Level Name Address ContentsNetwork Status CVM1, and CV-series PLCs Word Bits Contents SEND/RECV Flag OperationsCommunications Instruction Response Codes Example C200HX/HG/HE CQM1H-series PLCResponse Codes CS/CJ-series, CVM1, Simultaneous Execution of Communications Instructions C200HX/HG/HE PLCs CS/CJ-series, CVM1, and CV-series PLCs PLC Programming Examples On the next 195 196 197 198 Sending and Receiving Fins Commands and Responses Fins Commands and ResponsesFins Communications Service Applicable Units for Fins Commands Command CodesAny parameters must follow the command code Execution result Commands and Responses for Controller Link Units Command CodesCommand Block Response Block Response Block For C200HX/HG/HE, CVM1, and CV-series PLCs For CS/CJ-series and CQM1H-series PLCsParameters Model Unit. Always set to 00 Hex Wired/Optical responseReads the Controller Link Unit’s controller status 204 Network Status Read Corresponding to the node address 0 0 0 0 Default value 32 nodes Reads the data link operational statusIfied as a 2-byte 4-digit hexadecimal number as follows Hex 32 nodes 208 Data that was sent by the command One was sent is returned Reads the PLC’s error log Broadcasts test data to all nodes in a specified networkHexadecimal decimal 0 to Response gives the number of records actually read Error LOG Clear Configuration of each error record is as follows Command PLC mode Name Code Memory Area Designations Specified for CQM1H-series PLCs Word/Bit AddressesEach word/bit address specifies a specific bit or word Memory Area Code Data Configuration Word Contents or PV Two BytesParameters Memory area code command The data area to read Flag or Bit Status One Byte Memory area Data No. Code Bytes Parameters Memory area code command The data area to writeMemory Areas Sequence starting from the beginning address Memory area designations Program Area Write Data command The data to be written 02 Hex Monitor mode 04 Hex RUN mode8 RUN Stop Area data response As follows Meaning Unit Hex 0 0 Command Block Response BlockReads the status of the Controller Clock Read Value Day Parameters Error reset code command Set to Ffff Hex Parameters Range Value Function Memory area Data Area Data type Memory area Number Code Bytes ResponseDesignations for memory area designations IR, SR, LR, HR, and AR Areas ConfigurationResponse Codes Network Relay Errors Relay Errors Response Codes and Troubleshooting To some cause such as a routing table errorCPU Unit Exist 228 229 230 231 232 Network Interconnections Interconnecting Different Types of Networks What is Network Interconnection?Interconnecting Controller Link Networks 235 Sysmac Support Software and CV Support Software Remote Programming and MonitoringLocal Networks Remote Controller Link Networks Sysmac Support Software or CV Support Software Other Remote Networks CX-Programmer Programming Device Routing Tables Creating Routing TablesAppropriate Unit according to the routing tables Local Network Table Setting Routing Tables CreatedRelay Network Table Network end network not directly connected to the local PLC Local network Routing Table Setting ProcedureEditing Local Network Tables Editing Relay Network Tables Saving Routing Tables Connecting to the PLC Routing Table Enable Bit C200HX/HG/HE and CQM1H-series OnlyTransferring Routing Tables Operating level 0 DM Operating level 1 DM Example Routing Table Settings PCs Nodes Routing Tables on PLC 246 Communications Timing Communications Mechanism Data Transmissions over the Network Setting the Polling and Polled Nodes Network Parameters No. of Polled Nodes per Communications Cycle Network parameter Setting Default Range Value Communications Cycle TimeSpecifying Network Parameters Active Data Links Instruction When sent When received Inactive Data LinksCalculation Example Communications conditions are as follows Being issued Data Link I/O Response TimeData Exchange Timing Bytes Synchronous Mode Data Processing TimeUnder Asynchronous CS/CJ-series PLCs, CVM1 Calculation Example Time Case 257 258 259 260 261 Minimum Response Time CVM1 and CV-series PLCs Under Asynchronous Operation Maximum Response Time 264 Message Delay Times 1 CS/CJ-series, CVM1, and CV-series PLCsData Processing Time see Data Transmission Time Link Service Processing Source and Destination Nodes Transmission Delay TimeLink Servicing Interval Source and Destination Nodes Transmission Processing That transmits event frames before the Send command is sent Maximum Delay TimeReception Processing Number of words transferred ⋅ 0.00075 + 1.3 ms 268 269 2 C200HX/HG/HE and CQM1H-series PLCs SEND90Responses Number of words transferred ⋅ 0.00125 ms + 3 ms Responses Number of words transferred ⋅ 0.00125 ms + 2.3 ms RECV98 Instruction 272 273 274 Troubleshooting and Maintenance Troubleshooting Using Indicators Troubleshooting with RUN, ERC, ERH and INS Indicators1 CS/CJ-series Controller Link Units CS-series Unit 277 278 Troubleshooting with LNK and M/A Indicators Using the following tableData Link Cannot be Started Troubleshooting of Other Errors Node Cannot ParticipateData Link Stopped Configuring a Network with 33 Nodes or More Problem Status Cause and remedy 282 Configuring a Network with 32 Nodes or Less 2 C200HX/HG/HE and CQM1H-series Controller Link Units 284 285 286 CVM1 and CV-series Controller Link Units 288 289 290 291 Troubleshooting with the T/R1 and T/R2 Indicators Status Area and TroubleshootingTroubleshooting with the PWR Indicator Error Information CIO 1500 + 25 x Unit No Status Area 294 Bit status Probable cause Probable remedy Bit Status and Error ProcessingData Link Status 296 Refer to 7-4 Setting Rout Other Status Terminating Resistance Status CIO 1500 + 25 ⋅ Unit No. + Stopping Data Links Duplicate Operating Levels/Refresh Error AR Routing Table Error/Unit Restart Bits ARService Time AR 16, AR 2 C200HX/HG/HE Controller Link Units Operating Level Status SR Polling Node Address, Startup Node Address SR 238, SRData Link Status SR 239 to SR 241, SR 243 to SR Troubleshooting with Status Flags Data Link Status First Data Link Status Word + 0 to + 302 303 Error Information CIO 1500 + 25 ⋅ Unit No 3 CVM1 and CV-series Controller Link Units Data Link Status CIO 1500 + 25 ⋅ Unit No. + 7 to + 306 307 Error Information IR 4 CQM1H-series Controller Link Units Polling Node Address, Startup Node Address IR Network Participation Status IR 192 and IRLocal Data Link Participation Status IR Data Link Status IR 91 to IR 310 311 Routing Tabless and reset Terminating Resistance Status IR Error Log Table Configuration Error LogError Log Table Error Codes Tents of the errorsTime Information 1st byte 2nd byte 315 Command block Response block 317 318 319 Reading and Clearing Error Logs Error StatusReading an Error Log Clearing an Error Log Example Display of Error List Error message Troubleshooting 322 Cleaning and Inspection CleaningInspection Tools and Equipment Need for Inspection Handling Precautions Replacing the UnitBit address Unit Word Unit Setting the Unit after Replacement Resetting Network Parameters 326 Using the Controller Link Support Software Not Using the Controller Link Support softwareC200HX/HG/HE and CQM1H-series Controller Link Units 3.. . Turn off all nodes in the Controller Link Network CS/CJ-series, CVM1, and CV-series Controller Link Units 329 330 Adding Nodes and Editing Active Data Link Tables Example of Adding Nodes with a Repeater Unit on One End Adding Nodes Using a Repeater UnitExample of Adding Nodes Using a T-branch Line Procedure for Adding Nodes Precautions when Connecting Nodes Using a Repeater Unit System Configuration after Adding Nodes Adding Nodes with a Repeater Unit at One End Systems Wired with an Existing Repeater Unit Systems with an Existing T-branch Line Operations when Changing Data Link Tables Changing the Data Link Tables with Active Data LinksExample of Changing Data Link Table with Active Data Links Model Remarks 337 Procedure 339 340 341 342 Standard Models Controller Link Units Controller Link Support BoardController Link Support Software Communications Cables Twisted-pair Cables CX-Programmer with CX-Net CPU Units and Programming DevicesCPU Units Applicable Name Model number Applicable PLCs Computer Other Products Used with Controller Link Units Page Auxiliary Area Memory AreasCS/CJ-series PLCs CS/CJ CPU Bus Unit Duplication Error Flag CS/CJ CPU Bus Unit Error, Unit Number FlagsError Information CIO 1500 + 25 ⋅ Unit No. See CIO Area CS/CJ CPU Bus Unit Area 349 350 DM Area CS/CJ CPU Bus Unit Area Memory AreasAppendix B Common Type To 1 Type Chain Type Communications Instruction Response Codes SR 237 See C200HX/HG/HE PLCsSR Area Duplicate Operating Levels/Refresh Error AR 00 See Routing Table Error/Unit Restart Bits AR 01 SeeAR Area Operating Level Status SR 252 See pages 189 Service Time AR 16, AR 17 See DM Parameter Area CVM1 and CV-series PLCs CIO Area CPU Bus Unit Area CPU Bus Unit Numbers 359 DM Area CPU Bus Unit Area Data Link Start Bit AR 07 See Word Bits Name ContentsCQM1H-series PLCs Terminating Resistance Status IR 95 See Local Data Link Participation Status IR 90 SeeData Link Status IR 91 to IR 93 See pages 156 PLC Setup Settings in DM Area Controller Link Status Information Automatic Data Link Parameters DM 6401 to DM 6409 See Using the Relay Terminal Block Appearance Name Model number Remarks Replacing a Controller Link Unit with a Relay Terminal Block 367 Page Numerics Index 371 372 373 374 Revision code Date Revised content Revision History Revision History Pages 115, 117, 119, and 120 PC changed to PLC Omron Corporation Control Devices Division H.Q Regional Headquarters Authorized Distributor