Manuals / Omron / Computer Equipment / Network Card

Omron C200HW-CLK21, CVM1-CLK21, CS1W-RPT01 Adding Nodes with a Repeater Unit at One End

Models: CS1W-RPT01 CJ1W-CLK21-V1 CVM1-CLK21 CQM1H-CLK21 CS1W-CLK21-V1 C200HW-CLK21

1 401

Download 401 pages 33.98 Kb

Page 357

Adding Nodes Using a Repeater Unit

Section 10-1

•If automatic settings are used, make sure that the appropriate DM Area parameters have been set.

Check that the new data transmission that will be performed due to the new nodes has been considered in the user program for the existing network before adding the nodes. If the ladder program is not suitable, the system may not operate properly.

Make sure that the node addresses of the new nodes are not already being used by other nodes in the same network. If the same node address is used by more than one node, a node duplication error will be detected when the node is added, communications will stop, and the node with the same address will not be able to the join the network. Data may also be unexpectedly received from the incorrectly set node. To restore a Controller Link Unit with a duplicated address, reset the node address correctly, then turn ON the power to the corresponding PLCs again, or restart the Controller Link Units.

Always set the baud rate of the new nodes and the Repeater Unit to the same baud rate used for the existing network. If a different baud rate is set when adding a new node, the communications for the whole network including the existing network will be unstable and communications errors will occur.

Set the terminating resistance of the new nodes to the Repeater Unit as shown in the following diagram. If terminating resistance is set incorrectly, communications errors may occur.

• Adding Nodes Using T-branch Lines

System Configuration after Adding Nodes

Terminating resistance ON

CS1W-RPT01

Repeater Unit

Turn ON terminating resistance at the nodes on both ends of each segment shown within broken lines.

Terminating resistance ON

Terminating resistance ON

Newly added nodes

Terminating resistance ON

• Adding Nodes with a Repeater Unit at One End

Terminating resistance ON

CS1W-RPT01

Repeater Unit

Turn ON terminating resistance at the nodes on both ends of each segment shown within broken lines.

Terminating resistance ON

Terminating

resistance ON

Newly added nodes

Terminating resistance ON

334

Image 357

Omron C200HW-CLK21, CVM1-CLK21 Adding Nodes with a Repeater Unit at One End, System Configuration after Adding Nodes

Contents

Controller Link Units Controller Link Units Page  Omron Omron Product ReferencesUnit Versions Unit Version Notation on ProductsConfirming Unit Versions with Support Software Unit Version Notation Using the Unit Version LabelsFunction Support by Unit Version Unit Versions and Manufacturing Dates/Lot NumbersViii Table of Contents Data Links 105 Appendices Xii About this Manual Name Contents Cat. No Suffixes omittedXiv Read and Understand this Manual Application Considerations Disclaimers Xviii Precautions General Precautions Safety PrecautionsIntended Audience Operating Environment Precautions Operating Environment PrecautionsApplications Precautions Xxiii Conformance to EC Directives EMC DirectivesLow Voltage Directive Section Wired System What Is the Controller Link?Overview SectionBranch Wiring Long-distance WiringConverting Part of the Transmission Line to Optical Fiber CS1W-CLK12-V1 CVM1-CLK12 Token Ring ModeConnecting Repeater Units Using GI Optical Fiber Cable Token Bus ModeAutomatic Setting Message ServiceManual Setting Data LinksError Log Or the message service functionStatus Area Features of Twisted-pair Cable FeaturesFeatures of Optical Fiber Cable SpecificationsCompatible with Different Node Configurations Improved Error HandlingFlexible Inter-network Connections Total length of wired networks can be extended Features and Functions of Version-1 ModelsDevices can be modularized Up to 62 nodes can be connectedSystem Configuration Specifications and ConfigurationsBranch Wiring Maximum Configuration of 62 Nodes General SpecificationsItems Specifications Communications SpecificationsPCF type GI type Within 1 segment See Entire networkController Link Unit Models and PLCs Wired SystemTables Weight External Appearance InstallationMax No. Units per PLCCS/CJ-series Controller Link Unit Models Unit Ver .2 Pre-Ver .2 Without -V1 suffix SuffixName Model Current consumption Number Per Unit a Units Repeater Units when Required Devices for ConnectionCommunications Cables Name Model Remarks Relay Terminal BlocksProgramming Devices Programming Device for the PLCProgramming External Model Applicable PLCs Device Controller Link Support Software Version Using an Independent ComputerEV2 HG/HE, CVM1 Software External Model Applicable PLCs RemarksCX-Programmer Controller Link Support Software Menu OverviewWhen Operating on Personal Computer Connected as a Node When Operating on Personal Computer as Peripheral SoftwareSelection of Communications Functions Software External Model Applicable PLCsBasic Procedures Preparations C200HX/HG/HE and CQM1H-series PLCsCVM1, CV-series, and CS/CJ-series PLCs Application Precautions C200HX/HG/HE PLC Communications error type Data link areasSection Section Basic Procedures Manually Setting Data Links Data Links ProceduresSet the data link mode Start the data links Automatically Setting Data LinksCS/CJ Series Word 0 of DM30000 + 100 ⋅ AR 0700 operating level #0CV-series PLCs Console Only Gramming Console Section CX-Programmer version 3.2 or higher To 1 TypeCS/CJ Series Word 0 of DM30000 + 100 ⋅ N Chain TypeRegister routing tables if using inter-network connections Message Service ProcedureContents Remarks Create the I/O tablesCreate the user program Section Installation and Wiring CS-series Controller Link Units Component Names and FunctionsName Color Status Meaning Wired Unit IndicatorsCJ-series Controller Link Units Dimensions Unit mmFor details, refer to 9-1 Troubleshooting Using Indicators Component Names and Functions 3 C200HX/HG/HE Controller Link Unit Node address switches Refer to pYellow Lit Data reception Receive Not lit No data reception 4 CVM1 and CV-series Controller Link Unit Unit number switches Refer to p34.5 5 CQM1H-series Controller Link Unit Wire-to-Wire Repeater Unit Dimensions Unit mm Repeater Unit IndicatorsWire-to-Optical H-PCF Repeater Unit Wire-to-Optical GI Repeater Unit Unit Installation Installing Two Controller Link Units Installing One Controller Link UnitMounting Controller Link Units C200HX/HG/HE PLCsInstalling with Another Communications Unit Installing with a PC Card UnitCVM1 and CV-series PLCs Expansion CPU Rack CS-series PLCsCPU Rack CJ-series PLCs Mum current of 4.6 a 5 V and maximum power of 30 W Mounting a Repeater UnitCQM1H-series PLCs Screw-mounting a Repeater Unit Mounting a Repeater Unit on DIN TrackDIN Track Communications Cables WiringCommunications Cables End Plate PFP-M 2 Plates required per Repeater UnitConnecting the Shield Line Terminal Block ConnectionsNot Unit a Relay Terminal Block Using a Relay Terminal Block Connecting the Communications CablesApply vinyl tape or a heat-shrinking tube Do not pull on a communication cable Power Supply Wiring Mark Signal name Line colorRepeater Units Laying Optical Cable CS1W-RPT02/03 Only Power Supply SpecificationsMounting bracket Tension member Terminal Name Model Specifications Name Specifications ModelOptical Bus or Optical Ring System H-PCF Cable Optical Fiber Cables Indoor Use OnlyOptical Fiber Cable Accessories Optical Fiber Cables with Connectors Indoor Use OnlySpecifications Length Model Name Model Specifications ManufacturerCS1W-RPT03 GI Optical Fiber Cables 50/125 ∝m AGF CableMinimum Standard Maximum Unit Conditions Connectors Constructing Networks with Repeater Units62.5/125 ∝m AGF Cable Segments Specifications within Remarks Each segmentBranch Wiring 2-stage Repeater Unit Connection Number of Repeater UnitsExamples of Correct Repeater Unit Connections Examples of Incorrect Repeater Unit Connections Long-distance Wiring 2-stage Repeater Unit ConnectionPartial Optical Conversion 2-stage Repeater Unit Connection More than 2 Stages of Repeater UnitsBranch Wiring Long-distance WiringTerminating Resistance Partial Conversion to Optical Fiber Section Preparations for Communications CS-series Controller Link Units OverviewUnit Number Node Addresses Baud Rates Pins Baud rate Maximum Transmission distanceDefault setting is 2 Mbps, 500 m Bottom switch Terminating resistanceCJ-series Controller Link Units Setting range Nodes 01 to 32 default is Setting range Nodes To F default isNode Baud Rates C200HX/HG/HE PLC C200HX/HG/HE Controller Link UnitsBaud Rate and Operating Level Always leave pin 3 OFFOperating Level Setting the Operating Baud Rate Pins 1Baud Rates and Operating Levels Level PinPin Operating level Node Always keep pins 3 and 4 set to OFF Setting Baud RatesCVM1 and CV-series Controller Link Units Node AddressesUnit Set the following pins for the baud rate setting DIP switch Switch Baud rate Maximum Transmission distance PinSwitch at the front Terminating resistance Switch Terminating Nodes Resistance Setting Baud RateCQM1H-series Controller Link Units Pin Sion dis Tance101 Repeater Units Wire-to Repeater Wire-to-Wire Repeater UnitTerminating Resistance Switch for SL1 Terminating Resistance Switch for SL2Switch Terminating resistance Data Links Manually Setting Data Links What Are Data Links?CS/CJ-series Controller Link Unit Functions by Unit Version Offsets Easy SettingAutomatic Setting Data Links with 1N Allocations Automatically Setting Data Links with Equality LayoutType Model Offsetting Image Using OffsetsData Link Specifications Communications error type Data link areaDescription Manual setting Automatic setting Differences between Manual and Automatic SettingSelecting Manual or Automatic Setting Setting Data LinksTransferring from a Programming Device Manual SettingSetting item Setting range Data Link Table SpecificationsTransferring from a Computer Node CS/CJ-series PLCs116 C200HX/HG/HE PLCs 118 Used. Refer to 5-4 Checking Data Link Status for details CVM1 and CV-series PLCsCQM1H-series PLCs 121 Data link start word 1 + Total number of send/receive PrecautionsWords in area ≤ 247 IR Area W307 for information on the Controller Link Support BoardDevice Information Settings Manual Setting ExamplesSAMPLE1.CLK Same Allocation to All Nodes Data Link Area Structure124 SAMPLE2.CLK Different Allocations to Each Node Device Information SettingSAMPLE3.CLK Creating Data Link Groups within a Network Device Information Setting Data Link Tables Only area 2 is used in this example SAMPLE4.CLK Receiving Only Part of Send Data and OffsetsAutomatic Setting CS/CJ-series Startup Node Automatic Setting, Equality LayoutAutomatic Setting, 1N AllocationsBetween master and slave nodes Equality Layout Setting Range for Automatic Setting133 1N Allocation, Common Type Features of Common Type 1N Allocation135 136 137 1N Allocations, 1 to 1 Type Features of 1 to 1 Type 1N Allocation139 140 1N Allocation, Chain Type Features of Chain Type 1N Allocation142 143 144 C200HX/HG/HE Startup Node Settings146 CVM1 or CV-series Startup Node 148 149 CQM1H-series Startup Node Settings for Equality Layout Automatic Setting ExampleLink areas that are created as a result DM Parameter AreaData Link Areas Created DM Parameter Setting Example for 1N Allocation, Common TypeData Link Areas Starting and Stopping Data LinksManually Set Data Links Automatically Set Data LinksUsing a Programming Device or the User Program CS/CJ-series Start BitC200HX/HG/HE Start Bit Using Fins Commands Check the Link and M/A indicators on the front of the unit LED IndicatorsName Color Status Contents Checking Data Link Status157 Following shows an example of a remaining receive area Name Function Data Link Status Storage Format CS/CJ Series Only Data link status storage area is set as followsOnly status for nodes 1 to 6 are saved Matic settings SpecificationChecking by Manipulating Bit/Word Status Error Detection Program Example Programming Examples for Processing Data when Errors OccurProcessing Data Only when Data Links Are Operating Normally Data Link Example Communications Error at Node Writing 0000 in the Data Link Area when Errors Occur164 Message Service Introduction CS/CJ-series PLCs Send and Recv168 @SEND90 C200HX/HG/HE PLCs170 171 CIO Timer/counters numbers 0 to 2047 can send and receive dataWord for data reception at the destination node, N Section CVM1 and CV-series PLCs174 CQM1H-series PLCs 176 177 178 179 180 181 Cmnd Beginning word for storing response dataType of command Code Example Commands for CVM1, CV-series and CS/CJ-series PLCsArea Range Send/Receive Data AreasCVM1-CPU11/21 Area Range CV500, CVM1-CPU01Selecting Communications Instructions Tents ComPuter Or CV Read/writeMessage Service Specifications Using the Message Service Name Address Contents Word BitSEND/RECV Flags Name Address Contents Name Operating Address Contents LevelNetwork Status CVM1, and CV-series PLCsSEND/RECV Flag Operations Word Bits ContentsCommunications Instruction Response Codes ExampleCQM1H-series PLC C200HX/HG/HEResponse Codes CS/CJ-series, CVM1,C200HX/HG/HE PLCs CS/CJ-series, CVM1, and CV-series PLCs Simultaneous Execution of Communications InstructionsOn the next PLC Programming Examples195 196 197 198 Fins Commands and Responses Fins Communications ServiceSending and Receiving Fins Commands and Responses Command Codes Applicable Units for Fins CommandsAny parameters must follow the command code Execution resultCommand Codes Commands and Responses for Controller Link UnitsCommand Block Response BlockFor CS/CJ-series and CQM1H-series PLCs Response Block For C200HX/HG/HE, CVM1, and CV-series PLCsParameters ModelWired/Optical response Reads the Controller Link Unit’s controller statusUnit. Always set to 00 Hex 204 Corresponding to the node address Network Status Read0 0 0 0 Reads the data link operational status Default value 32 nodesIfied as a 2-byte 4-digit hexadecimal number as follows Hex 32 nodes208 One was sent is returned Data that was sent by the commandBroadcasts test data to all nodes in a specified network Reads the PLC’s error logHexadecimal decimal 0 to Response gives the number of records actually readConfiguration of each error record is as follows Error LOG ClearMemory Area Designations Command PLC mode Name CodeWord/Bit Addresses Specified for CQM1H-series PLCsEach word/bit address specifies a specific bit or word Memory Area CodeWord Contents or PV Two Bytes Data ConfigurationParameters Memory area code command The data area to read Flag or Bit Status One ByteParameters Memory area code command The data area to write Memory AreasMemory area Data No. Code Bytes Memory area designations Sequence starting from the beginning addressProgram Area Write 02 Hex Monitor mode 04 Hex RUN mode Data command The data to be written8 RUN StopMeaning Unit Hex Area data response As followsCommand Block Response Block Reads the status of the Controller0 0 Value Day Clock ReadParameters Range Parameters Error reset code command Set to Ffff HexMemory area Data Value FunctionResponse Designations for memory area designationsArea Data type Memory area Number Code Bytes Configuration Response CodesIR, SR, LR, HR, and AR Areas Relay Errors Network Relay ErrorsTo some cause such as a routing table error Response Codes and TroubleshootingCPU Unit Exist228 229 230 231 232 Network Interconnections What is Network Interconnection? Interconnecting Controller Link NetworksInterconnecting Different Types of Networks 235 Remote Programming and Monitoring Local NetworksSysmac Support Software and CV Support Software Sysmac Support Software or CV Support Software Remote Controller Link NetworksCX-Programmer Programming Device Other Remote NetworksCreating Routing Tables Routing TablesAppropriate Unit according to the routing tables Local Network TableCreated Setting Routing TablesRelay Network Table Network end network not directly connected to the local PLCRouting Table Setting Procedure Editing Local Network TablesLocal network Saving Routing Tables Editing Relay Network TablesRouting Table Enable Bit C200HX/HG/HE and CQM1H-series Only Connecting to the PLCTransferring Routing Tables Operating level 0 DM Operating level 1 DMPCs Example Routing Table SettingsRouting Tables on PLC Nodes246 Communications Timing Data Transmissions over the Network Communications MechanismSetting the Polling and Polled Nodes No. of Polled Nodes per Communications Cycle Network ParametersCommunications Cycle Time Network parameter Setting Default Range ValueSpecifying Network Parameters Active Data LinksInactive Data Links Instruction When sent When receivedCalculation Example Communications conditions are as followsData Link I/O Response Time Being issuedData Exchange Timing BytesData Processing Time Synchronous ModeUnder Asynchronous CS/CJ-series PLCs, CVM1Calculation Example Time Case 257 258 259 260 261 Minimum Response Time Maximum Response Time CVM1 and CV-series PLCs Under Asynchronous Operation264 1 CS/CJ-series, CVM1, and CV-series PLCs Message Delay TimesData Processing Time see Data Transmission TimeTransmission Delay Time Link Service Processing Source and Destination NodesLink Servicing Interval Source and Destination Nodes Transmission ProcessingMaximum Delay Time That transmits event frames before the Send command is sentReception Processing Number of words transferred ⋅ 0.00075 + 1.3 ms268 269 SEND90 2 C200HX/HG/HE and CQM1H-series PLCsResponses Number of words transferred ⋅ 0.00125 ms + 3 ms Responses Number of words transferred ⋅ 0.00125 ms + 2.3 msRECV98 Instruction 272 273 274 Troubleshooting and Maintenance Troubleshooting with RUN, ERC, ERH and INS Indicators Troubleshooting Using Indicators1 CS/CJ-series Controller Link Units CS-series Unit277 278 Using the following table Troubleshooting with LNK and M/A IndicatorsData Link Cannot be StartedNode Cannot Participate Troubleshooting of Other ErrorsData Link StoppedProblem Status Cause and remedy Configuring a Network with 33 Nodes or More282 2 C200HX/HG/HE and CQM1H-series Controller Link Units Configuring a Network with 32 Nodes or Less284 285 286 CVM1 and CV-series Controller Link Units 288 289 290 291 Status Area and Troubleshooting Troubleshooting with the PWR IndicatorTroubleshooting with the T/R1 and T/R2 Indicators Status Area Error Information CIO 1500 + 25 x Unit No294 Bit Status and Error Processing Data Link StatusBit status Probable cause Probable remedy 296 Other Status Refer to 7-4 Setting RoutStopping Data Links Terminating Resistance Status CIO 1500 + 25 ⋅ Unit No. +Routing Table Error/Unit Restart Bits AR Duplicate Operating Levels/Refresh Error ARService Time AR 16, AR 2 C200HX/HG/HE Controller Link UnitsPolling Node Address, Startup Node Address SR 238, SR Data Link Status SR 239 to SR 241, SR 243 to SROperating Level Status SR Data Link Status First Data Link Status Word + 0 to + Troubleshooting with Status Flags302 303 3 CVM1 and CV-series Controller Link Units Error Information CIO 1500 + 25 ⋅ Unit NoData Link Status CIO 1500 + 25 ⋅ Unit No. + 7 to + 306 307 4 CQM1H-series Controller Link Units Error Information IRNetwork Participation Status IR 192 and IR Polling Node Address, Startup Node Address IRLocal Data Link Participation Status IR Data Link Status IR 91 to IR310 311 Terminating Resistance Status IR Routing Tabless and resetError Log Error Log TableError Log Table Configuration Tents of the errors Error CodesTime Information 1st byte 2nd byte315 Response block Command block317 318 319 Error Status Reading and Clearing Error LogsReading an Error Log Clearing an Error LogError message Troubleshooting Example Display of Error List322 Cleaning Cleaning and InspectionInspection Tools and Equipment Need for InspectionReplacing the Unit Handling PrecautionsBit address Unit Word UnitResetting Network Parameters Setting the Unit after Replacement326 Not Using the Controller Link Support software Using the Controller Link Support SoftwareC200HX/HG/HE and CQM1H-series Controller Link Units 3.. . Turn off all nodes in the Controller Link NetworkCS/CJ-series, CVM1, and CV-series Controller Link Units 329 330 Adding Nodes and Editing Active Data Link Tables Adding Nodes Using a Repeater Unit Example of Adding Nodes Using a T-branch LineExample of Adding Nodes with a Repeater Unit on One End Precautions when Connecting Nodes Using a Repeater Unit Procedure for Adding NodesAdding Nodes with a Repeater Unit at One End System Configuration after Adding NodesSystems with an Existing T-branch Line Systems Wired with an Existing Repeater UnitChanging the Data Link Tables with Active Data Links Operations when Changing Data Link TablesExample of Changing Data Link Table with Active Data Links Model Remarks337 Procedure 339 340 341 342 Controller Link Support Board Standard Models Controller Link UnitsController Link Support Software Communications Cables Twisted-pair CablesCPU Units and Programming Devices CX-Programmer with CX-NetCPU Units Applicable Name Model number Applicable PLCs ComputerOther Products Used with Controller Link Units Page Memory Areas CS/CJ-series PLCsAuxiliary Area CS/CJ CPU Bus Unit Error, Unit Number Flags CS/CJ CPU Bus Unit Duplication Error FlagError Information CIO 1500 + 25 ⋅ Unit No. See CIO Area CS/CJ CPU Bus Unit Area349 350 DM Area CS/CJ CPU Bus Unit Area Common Type Memory AreasAppendix BChain Type To 1 TypeC200HX/HG/HE PLCs SR AreaCommunications Instruction Response Codes SR 237 See Routing Table Error/Unit Restart Bits AR 01 See Duplicate Operating Levels/Refresh Error AR 00 SeeAR Area Operating Level Status SR 252 See pages 189DM Parameter Area Service Time AR 16, AR 17 SeeCVM1 and CV-series PLCs CPU Bus Unit Numbers CIO Area CPU Bus Unit Area359 DM Area CPU Bus Unit Area Word Bits Name Contents CQM1H-series PLCsData Link Start Bit AR 07 See Local Data Link Participation Status IR 90 See Data Link Status IR 91 to IR 93 See pages 156Terminating Resistance Status IR 95 See Controller Link Status Information PLC Setup Settings in DM AreaAutomatic Data Link Parameters DM 6401 to DM 6409 See Appearance Name Model number Remarks Using the Relay Terminal BlockReplacing a Controller Link Unit with a Relay Terminal Block 367 Page Numerics Index 371 372 373 374 Revision History Revision code Date Revised contentPages 115, 117, 119, and 120 PC changed to PLC Revision HistoryRegional Headquarters Omron Corporation Control Devices Division H.QAuthorized Distributor