aK==tçêâáåÖ=táíÜ=aÉëíáå~íáçåë

ScreenPRO-II Configurations

SDI

Inputs

Analog Inputs

bñíÉêå~ä=bíÜÉêåÉí=oçìíÉê=`çåÑáÖìê~íáçå

The diagram below shows a configuration that uses two ScreenPRO-II units with external source routing. Each ScreenPRO-II is set up as a unique destination. Two external Ethernet routers are used — one for analog connections and one for SDI source connections to each ScreenPRO-II.

Inputs

 

ScreenPRO-II

Side Screen 1

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Router

 

 

 

 

 

 

 

 

 

 

MatrixPRO SDI Router

 

 

 

Outputs

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

MatrixPRO Analog Router

Side Screen 2

Encore Controller (SC or LC)

Ethernet Switch

Figure D-3.ScreenPRO-II units using external Ethernet controlled routers

For an “external routing” configuration with Ethernet controlled routers, please note the following points regarding destination setup and source connections:

On the Destination Setup Menu:

~Select Single Screen SP as the “Type.”

~Set the “Routing Mode” to External.

~In Chapter 6, refer to the ScreenPRO-II Destination Setup” section on page 279 for instructions.

Connect analog and digital sources to each router in the normal manner.

For each router, connect two outputs to each ScreenPRO-II.

On the Router Specification Menu, select the correct router and manufacturer, and set the “Communication Type” to ETHERNET. In Chapter 6, refer to the “Router Setup” section on page 270 for instructions.

Router outputs are mapped using the Output Patch Menu. This menu defines which router output connects to which ScreenPRO-II input. In Chapter 6, refer to the “Router Setup” section on page 270 for instructions.

Router inputs are mapped using the Input Patch Menu. In Chapter 6, refer to the “Output Format Setup” section on page 285 for instructions.

396

 

Encore Presentation System • User’s Guide • Rev 04

 

Page 396
Image 396
Barco 26-0313000-00 manual BñíÉêå~ä=bíÜÉêåÉí=oçìíÉê=`çåÑáÖìê~íáçå