Display ip alias, Output for display interface | 3Com 3CRWX120695A

					display ip alias 119
WX4400# display interface			Mask	Enabled State
VLAN	Name	Address	Mask	Enabled State
----	---------------	---------------	---------------	------- -----
1	default	10.10.10.10	255.255.255.0	YES	Up
2	mauve	10.10.20.10	255.255.255.0	NO	Down
4094	web-aaa	10.10.10.1	255.255.255.0	YES	Up

Table 27 describes the fields in this display.

Table 27 Output for display interface

Field	Description

VLAN	VLAN number

Name	VLAN name

Address	IP address

Mask	Subnet mask

Enabled	Administrative state:
		YES (enabled)
		NO (disabled)

State	Link state:
		Up (operational)
		Down (unavailable)

See Also

set interface on page 135

set interface status on page 136

display ip alias

Shows the IP aliases configured on the wireless LAN switch.

Syntax — display ip alias [name]

name — Alias string.

Defaults — If you do not specify an alias name, all aliases are displayed.

Access — Enabled.

History —Introduced in MSS Version 3.0.

Image 119

3Com 3CRWX120695A Display ip alias, See Also „ set interface on „ set interface status on, Output for display interface

Contents

3CRWX120695A, 3CRWX440095A Wireless LAN Mobility System 3Com Corporation 350 Campus Drive Marlborough, MA USA Contents Set system location Clear banner motd Clear history Clear prompt Vlan Commands 147 Set ntp 148 131 Ping 132 Set arp 133 Set arp agingtime 134142 Set ip ssh 143 144 Display location policy 185 Display mobility-profile 169183 241 MAP Access Point Commands by Usage228 234 261 Reset ap dap 264 254 Display dap unconfigured 256 Display radio-profile 257 327 311319 326 345 335Set spantree 337 373 Commands by Usage 393369 Clear security acl 370 Clear security acl map 371 446 435444 480 465 Set rf detect countermeasures466 Set rfdetect ignore 467 Set rfdetect log 468 517 Commands by Usage 491 Clear log trace Clear trace 492Fver 519 Help 520 Next 521 Reset 522 Test 523 496 Set trace sm 497 Register Your Product 527 Version List conventions that are used throughout this guide Conventions Documentation „ Wireless LAN Switch Manager 3WXM Release Notes„ Wireless LAN Switch and Controller Release Notes „ Document part number and revision on the title CommentsPddtechpubscomments@3com.com „ Document title About this Guide Overview Clear fdb dynamic port port-list vlan vlan-id Set enablepassClear interface vlan-idip Notation Text EntryConventions MAC Address User Globs MasksSubnet Masks Wildcard Masks User Globs Gives examples of user globsMAC Address Globs „ a single port number. For example WX1200# set port enableVlan Globs Matching Order for Globs Operating systems Command-LineWX1200# reset port Editing WX1200# display i Tab WX1200# display i? Using CLI HelpAt your access level, type the help command. For example WX1200# display ip telnet Understanding Command DescriptionsSet ap dap name command has the following complete syntax WX1200# display ip ? Understanding Command Descriptions Using the COMMAND-LINE Interface Syntax disable Defaults None Commands byDisable To located commands in this chapter based on their use Quit Enable Set enablepass Access Commands To located commands in this chapter based on their use System Service Commands „ display banner motd on Banner with an empty banner by typing the following commandClear banner motd Clear history Clear system Clear prompt Motd Display banner Display license DisplayBase-information Shows system information Defaults None Access AllDisplay system „ set license on Display system output Describes the fields of display system output Nvram size /SDRAM size percent of total Syntax help WX switchHelp See Also „ clear history on HistorySyntax history Syntax set confirm on off Set confirmSee Also „ clear banner motd on „ display banner motd on That might have a large impact on the network WX4400# set confirm off Set lengthExamples To turn off these confirmation messages, type WX4400# clear vlan red See Also „ display license on Installs an upgrade license, for managing more MAPsSet license Syntax set prompt string Set prompt Syntax set system contact string Set system contact Stores a contact name for the WX switchSet system Countrycode Country Code Mobility Domain Defaults The factory default country code is NoneUsing any set ap commands to configure a MAP Ip-address Syntax set system location string See Also „ clear system on „ display system on Syntax set system name string „ set system contact on „ set system name on System Service Commands Locate commands in this chapter based on their use Port Commands „ set dap on That are using the MAPClear dap Removes a Distributed MAP Clear port name Removes the name assigned to a port Clear port-group„ name name Name of the port group See Also „ set port-groupon „ display port-groupon Interface for the active link Clear portPreference See Also „ display port status on „ set port name on Port Network port defaultsClear port type Network port Counters Display port Output for display port-group Display port-groupShows port group informationDescribes the fields in the display port-group output Syntax display port poe port-list See Also „ clear port-groupon „ set port-grouponDescribes the fields in this display Output for display port poe Specified ports Usage This command applies only to the WX4400All four ports of a WX4400 switch „ set port poe on Syntax display port status port-list Output for display port preference WX1200# display port status Output for display port status „ set port speed on Monitor portSee Also „ clear port type on „ set port negotiation on Key Controls for Monitor Port Counters Display WX4400# monitor port counters Output for monitor port counters Correct length but contained an invalid See Also „ display port counters on Set dap Reset port Port Commands Set dap Set port Examples The following command disables portFol1owing command reenables the port Administratively disables or reenables a port With no spaces Configured together as a single logical linkSingle logical link See Also „ clear port name on „ display port status on Name or number in other CLI commandsSet port name See Also „ clear port-groupon „ display port-groupon Result Set port negotiationSet port poe WX1200# set port poe 4,5 enable Following command enables PoE on ports 4See Also „ set port type ap on „ set port type wired-authon WX1200# set port poe 4,5 disable Syntax set port speed port-list10 100 1000 auto Set port speedChanges the speed of a port WX4400# set port preference 2 rj45 Set port trap Set snmp trap command Set port type ap „ 11a 802.11a „ 11b 802.11b „ 11g 802.11g Antenna model, use the following command„ poe enable disable Power over Ethernet PoE state Defaults All WX ports are network ports by default STP MAP Access Port Defaults Set port type Wired-auth WX1200# set port type wired-auth 2 success change accepted Wired Authentication Port Details See Also „ clear port type on „ set port type ap on Vlan Commands WX4400# clear fdb static vlan blue success change accepted Clear fdbDeletes an entry from the forwarding database FDB Syntax clear fdb perm static dynamic Port from the VLAN, make sure you specify the port number Clear vlan„ display fdb on Displays entries in the forwarding database Following command completely removes Vlan marigoldSee Also „ set vlan port on „ display vlan config on Display fdb WX4400# display fdb all Output for display fdb AgingtimeDescribes the fields in the display fdb output See Also „ clear fdb on Syntax display fdb count perm static dynamic See Also „ set fdb agingtime onWX1200# display fdb agingtime Station Display roaming Output for display roaming station Describes the fields in the displaySee Also „ display roaming vlan on WX4400# display roaming vlan Output for display roaming vlanSyntax display roaming vlan Syntax display tunnel See Also „ display vlan config onDisplay tunnel Output for display tunnel WX1200# display vlan config burgundy Display vlan configOutput for display vlan config Syntax display vlan config vlan-id Syntax set fdb perm static Set fdbAdds a permanent or static entry to the forwarding database See Also „ clear fdb on „ display fdb on Creates a Vlan and assigns a number and name to it Set vlan nameSee Also „ display fdb agingtime on Vlan 4094 is reserved for WebAAA Set vlan port Tunnel-affinity Set vlan See Also „ display roaming vlan on „ display vlan config on To locate commands in this chapter based on their use IP Services Commands DNS IP Services Commands by Usage Syntax clear interface vlan-idip Clear interfaceRemoves an IP interface WX1200# clear ip dns domain Access EnabledHistory Introduced in MSS Version See Also „ display ip alias on „ set ip dns server on Clear ip dns serverClear ip route „ set ip dns domain on „ set ip route on Clear ip telnet„ display ip route on Clear ntp Update-intervalClear ntp server See Also „ clear ntp server on „ display ntp on „ set ntp server on „ set ntp update-intervalonClear snmp trap Receiver Clear summertime Examples To clear the system IP address, type the following CommandFollowing command Clear timezone Shows the ARP table Display arpDisplay timedate on Display timezone on Syntax display interface vlan-id „ set arp on„ set arp agingtime on Output for display interface Shows the IP aliases configured on the wireless LAN switchDisplay ip alias See Also „ set interface on „ set interface status on „ set ip alias on Examples The following command displays the DNS informationDisplay ip dns „ clear ip alias on Syntax display ip https Display ip httpsShows information about the Https management port Output for display ip dns WX4400# display ip https Output for display ip https WX4400# display ip route Display ip routeShows the IP route table Syntax display ip route destination FieldDescription Output of display ip route WX4400 display ip telnet Output for display ip telnetSyntax display ip telnet Output for display ntp Examples To display NTP information for a WX switch, typeDisplay ntp Shows NTP client information „ set ntp server on „ set summertime on „ set timezone on Display snmp ConfigurationShows Snmp settings on a wireless LAN switch Examples To display Snmp settings on a WX switch, type Output of display snmp configuration WX1200# display summertime Defaults There is no summertime offset by defaultSummertime Syntax display summertime WX4400# display timezone WX1200# display timedateSyntax display timezone „ set timedate on „ set timezone on Defaults „ count „ traceroute on Set arp WX1200# set arp agingtime Following command disables ARP agingSee Also „ set arp agingtime on Syntax set arp agingtime seconds Set interface Syntax set interface vlan-idstatus up down WX1200# set interface mauve ip 10.10.20.10 See Also „ clear ip alias on „ display ip alias on Aliases as shortcuts in CLI commandsSet ip alias Set ip dns WX1200# set ip dns domain example.com Syntax set ip dns domain name Syntax set ip dns server ip-addrprimary secondary Adds a static route to the IP route table WX switch is also disabledSet ip route Set ip route Syntax set ip snmp server enable disable Secure Shell SSH management traffic See Also „ set ip ssh absolute-timeoutonSet ip ssh „ clear snmp trap receiver on Or idle Absolute-timeout„ set ip ssh idle-timeouton „ set ip ssh server on Syntax set ip ssh absolute-timeout minutes Set ip ssh server Idle-timeoutAlso disabled Set ip telnet WX4400# set ip telnet server enable success change accepted Syntax set ip telnet server enable disable Set ntp Examples The following command enables the NTP clientEnables or disables the NTP client on a wireless LAN switch Configures a wireless LAN switch to use an NTP server From 16 through 1,024 seconds RFC 1305, Network Time Protocol Version 3 SpecificationImplementation and Analysis NTP server Public and private Set snmpCommunity Sends an Snmp trap message to any network management system „ enable Enables trap information to be sent„ disable Disables the sending of trap information „ all Enables or disables all traps Snmp Trap Names Defaults All traps are disabled by default Access Enabled See Also „ clear snmp trap receiver on Set snmp trap IP Services Commands Following To PDT Pacific Daylight Time, type the following commandValues Date is within the summertime period „ time hhmmss System time, in hours, minutes, and seconds Sets the time of day and date on the wireless LAN switchSet timedate „ date mmm dd yyyy System date Time now is Sun Feb 29 2004, 235802 PST Set timezoneWX4400# set timedate date feb 29 2004 time WX1200# set timezone PST TelnetOpens a Telnet client session with a remote device WX4400# telnet See Also „ clear sessions on „ display sessions on „ queries „ size „ ttl Defaults„ dnf Disabled „ no-dns- Disabled „ port Traceroute WX4400# traceroute server1 Error messages for traceroute „ ping on AAA Commands by Usage Locate commands in this chapter based on their useThis chapter presents AAA commands alphabetically. Use to Display accounting statistics on WX4400# clear accounting dot1x Nin Syntax clear accounting admin dot1x user-glob Admin Clear authentication ConsoleConsole Syntax clear authentication console user-globWX4400# clear authentication console Regina Syntax clear authentication dot1x ssid ssid-namewired Syntax clear authentication mac ssid ssid-namewired Clear authentication Removes a MAC authentication rule. macSyntax clear authentication last-resort ssid ssid-namewired WX4400# clear authentication last-resort wired Syntax clear authentication web ssid ssid-namewired Clear authentication Removes a WebAAA rule. webWX4400# clear authentication mac ssid thatcorp aabbcc Syntax clear location policy rule-number See Also „ display aaa on „ set mac-usergroup attr on Clear mac-user„ display location policy on „ set location policy on „ set mac-user attr on Clear mac-user attrGroup Mac-usergroup Clear „ clear mac-usergroup attr on Mac-user group commandMac-usergroup attr Clear user Mobility-profile See Also „ display aaa on Clear user attr Clear usergroup Clear user group WX4400# clear usergroup cardiology success change accepted „ group-name- Name of an existing user groupSyntax clear usergroup group-name Time-Of-Day attribute from the group Displays all current AAA settingsDisplay aaa Display aaa Output Describes the fields that can appear in display aaa output User’s password, and no global password is set Statistics output Stored in the local database on the WX switchDisplay accounting Statistics Aaattyattr „ clear location policy on Display locationPolicy Are sent Admin consoleSet accounting Authenticated by MAC authentication Server when the user roamsAccesses the switch using Telnet or Web Manager Authenticated by AAA Commands Set authentication AAA Commands Following methods in priority order. MSS applies multiple Through the switch’s consoleCompleting logon Globs on For more information, see Usage Syntax set authentication dot1x ssid ssid-namewired AAA Commands Set authentication dot1x Success change accepted Syntax set authentication last-resort AAA Commands Syntax set authentication mac AAA Commands Syntax set authentication web ssid ssid-namewired AAA Commands Set location policy AAA Commands Set location policy WX4400# set location policy deny if user eq *.theirfirm.com Tempvendora into Vlan kiosk1 Set mac-user See Also „ clear mac-useron „ display aaa on Authentication Attributes for Local Users Filter-id outboundacl.out Authentication Attributes for Local Users YY/MM/DD-HHMM Time-of-day WX4400# set mac-user 010203040506 attr filter-id acl-03.in Syntax set mac-usergroup See Also „ clear mac-user attr on „ display aaa on Syntax set mobility-profile name name port none all See Also „ clear mac-usergroup attr on „ display aaa on AAA Commands „ set user attr on „ set usergroup on Syntax set mobility-profile mode enable disable See Also „ clear user on „ display aaa on Set user29Jan04 See Also „ clear user attr on „ display aaa on Set user attrOrange „ clear user group on Set user groupSet usergroup Set web-aaa To add a user to a group, user the command set user groupSyntax set web-aaa enable disable WX4400# set web-aaa disable success change accepted Examples To disable WebAAA, type the following command Mobility Domain Commands by Usage To locate commands in this chapter based on their use Member Mobility-domain See Also „ set mobility-domain member on Display mobility-domain configDisplays the configuration of the Mobility Domain Status WX4400# display mobility-domain status Display mobility-domain Output Seed-ip Mode member„ display mobility-domain config on Set Syntax set mobility-domain mode seed domain-name Set mobility-domain mode seed domain-name Domain name is Pleasanton Mobility Domain Commands Commands Managed Access Point Commands Map Access Point Commands by Usage Radio Clear ap dap Syntax clear radio-profile name parameter WX1200# clear ap 3 radio Syntax clear service-profile name „ name Service profile name See Also „ clear radio-profileon „ set radio-profile mode on WX4400# display dap config Output for display ap configWX1200# display ap config Does not belong to any load balancing groups An associated client Radio 1 Shows statistics counters for radio Displays MAP access point and radio statistics countersMAP access point on port Display ap dap Tkip Pkt Replays Output for display ap counters WX4400# display dap etherstats See Also „ display sessions network onSyntax display ap dap etherstats port-listdap-num TxMaxColl Output of display ap etherstats „ name Name of an MAP group or Distributed MAP group Syntax display ap status port-listall radio 1 Syntax WX1200# display ap status WX4400# display dap status Output for display ap status Output for display ap status Decide whether to change channel or power settings WX1200# display auto-tune attributes ap 2 radio See Also „ display auto-tune neighbors onOutput for display auto-tune attributes Neighbors Display auto-tune Display auto-tune Neighbors ap 2 radio Output for display auto-tune neighbors Connection Display dap Dap connection serial-id M9DE48B6EAD00 „ display ap dap config on„ display dap global on „ display dap unconfigured on Output of display dap connection WX4400# display dap global Output for display dap global Longer appears in the command’s output Unconfigured„ display ap dap config on But that are not configured on any WX switches Displays radio profile information Describes the fields in this display Output for display radio-profile WX4400# display radio-profile default Setting and tuning channels Ssid „ ? Displays a list of service profiles Service-profileDisplays service profile information „ name Displays information about the named service profile Username „ Tkip countermeasures time Indicates the amount Syntax set ap port-listdap dap-numbias high low Reset ap dapWX1200# reset ap WX4400# set dap 1 bias low success change accepted See Also „ display ap dap config on Syntax set ap port-listdap dap-numblink enable disable WX1200# set ap 3-4 blink enable success change accepted WX1200# set ap 1 name techpubs success change accepted Set ap dap name Changes an MAP name„ display ap dap group on WX1200# set ap 4 group none success change accepted „ antennatype ANT5060 ANT5120 ANT5180 internal Set ap dap radio antennatype„ antennatype ANT1060 ANT1120 ANT1180 internal Set ap dap radio auto-tune max-power Set ap dap radio auto-tune max- retransmissions Managed Access Point Commands Syntax set ap port-listdap dap-numradio 1 Set ap dap radio channelSets an MAP radio’s channel WX1200# set ap 5 radio 1 channel 36 success change accepted Set ap dap radio min-client-rate Set ap dap radio min-client-rate Following command enables radio 2 on ports 1 through Set ap dap radio modeEnables or disables a radio on an MAP access point Set ap dap radio radio-profile Sets an MAP radio’s transmit power Set ap dap radio tx-power Set ap dap Upgrade-firmware 11g-only Set radio-profile Set radio-profile auto-tune channel-config Syntax set radio-profile name auto-tune channel-holddown Set radio-profile auto-tune channel-holddown Syntax set radio-profile name auto-tune channel-interval Set radio-profile auto-tune channel-interval WX4400# set radio-profile rp2 auto-tune power-backoff-timer Set radio-profile auto-tune power-backoff- timerSyntax set radio-profile name auto-tune power-backoff-timer Set radio-profile auto-tune power-config Set radio-profile auto-tune power-interval Radio profile rp1 to 200 ms Service set identifier SsidBeacon-interval Specify from 25 ms to 8191 ms Syntax set radio-profile name frag-threshold threshold Syntax set radio-profile name long-retry threshold Syntax set radio-profile name max-rx-lifetime time Mode Max-tx-lifetime Parameter Default Value Defaults for Radio Profile Parameters WX4400# set radio-profile rp1 success change accepted WX4400# set radio-profile rp1 mode enable Syntax set radio-profile name Syntax set radio-profile name rts-threshold threshold Syntax set radio-profile name service-profile name Defaults for Service Profile Parameters 297 Defaults for Service Profile Parameters Syntax set radio-profile name short-retry threshold WPA IE Syntax set service-profile Name auth-dot1x enable disable Set service-profile auth-fallthru Syntax set service-profile name auth-psk enable disable Syntax set service-profile name beaconed enable disable Cipher-ccmp Set service-profile Cipher-tkip Cipher-wep104 Use the set service-profile wep commandsSee Also „ set service-profilecipher-ccmpon Cipher-wep104 command „ enable Enables 40-bit WEP encryption for WPA clients„ disable Disables 40-bit WEP encryption for WPA clients Defaults 40-bit WEP encryption is disabled by default Syntax set service-profile name psk-phrase passphrase Syntax set service-profile name psk-raw hex Syntax set service-profile name rsn-ie enable disable Syntax set service-profile name ssid-name ssid-name Set service-profile auth-psk command See Also „ set service-profilessid-nameon See Also „ set service-profilessid-typeon Syntax set service-profile name tkip-mc-time wait-time Web-aaa-form Ssid managed by the service profileSyntax set service-profile name web-aaa-form url „ mkdir on Set service-profile wep active-multicast- index„ copy on „ dir on Syntax set service-profile name wep active-unicast-index num Set service-profile wep active-unicast- index Wep key-index Syntax set service-profile name wpa-ie enable disable STP Commands by Usage STP Commands byTable to locate commands in this chapter based on their use Syntax clear spantree portcost port-list STP root bridge in all VLANs on a WX switchClear spantree Portcost „ set spantree portpri on PortpriPortvlancost „ clear spantree portvlanpri on „ clear spantree portcost on Portvlanpri See Also „ display spantree statistics on „ clear spantree portpri on Syntax display spantree Spantree vlan default Root Output for display spantree „ display spantree blockedports on Or disabledDisplay spantree Backbonefast One or all of its VLANs WX switch with backbone fast convergence enabledBlockedports „ set spantree backbonefast on Output for display spantree portfast PortfastFor one or more network ports See Also „ set spantree portfast on Syntax display spantree statistics Port’s VLANs„ port-list- List of ports Syntax display spantree portvlancost port-list WX4400# display spantree statistics Topology change Timer value Hold timer Vlan Vlan ID Output for display spantree statistics Configpending Switch is the root or is attempting to become the root Syntax display spantree uplinkfast vlan vlan-id See Also „ clear spantree statistics on „ set spantree uplinkfast on Set spantree An indirect link Examples The following command enables STP on all VLANsConfigured on a WX switch Following command disables STP on Vlan burgundy „ display spantree backbonefast on Fwddelay „ all Changes the maximum age on all VLANs Issues a topology change messageMaxage VLANs to 4 seconds 65,535. STP selects lower-cost paths over higher-cost paths Type. lists the defaults for STP port path costSnmp Port Path Cost Defaults Path to the STP root bridge Portvlancost command Syntax set spantree portpri port-listpriority value See Also „ display spantree portfast on To 20 in Vlan mauve Bridge for a specific Vlan on a wireless LAN switch„ all Changes the cost on all VLANs Type. See on Priority Primary link fails Uplinkfast32,768 Pink to See Also „ display spantree uplinkfast on Igmp Commands by Usage Igmp Snooping Commands See Also display igmp statistics on Clear igmp statisticsDisplay igmp TTL Output for display igmp TTL WX1200# display igmp Mrouter vlan orange MrouterSyntax display igmp mrouter vlan vlan-id Syntax display igmp querier vlan vlan-id Defaults None Access EnabledOnly one querier WX1200# display igmp querier vlan red WX1200# display igmp querier vlan defaultOutput for display igmp mrouter WX1200# display igmp querier vlan orange „ set igmp querier on Receiver-table WX1200# display igmp receiver-table group 237.255.255.0/24 See Also „ set igmp receiver onShows Igmp statistics VLAN, MSS displays Igmp statistics for all VLANs WX1200# display igmp statistics vlan orange From the multicast routers in the subnet Output of display igmp statistics See Also „ set igmp rv on Wireless LAN switch From 1 through 65,535 VLANs on a wireless LAN switchVLAN, the timer change applies to all VLANs Set igmp lmqi See Also „ display igmp statistics on Enables or disables multicast router solicitation by a WXSyntax set igmp mrsol enable disable vlan vlan-id Set igmp mrsol WX1200# set igmp mrsol mrsi 60 success change accepted See Also „ set igmp mrsol mrsi onSee Also „ set igmp mrsol on Syntax set igmp mrsol mrsi seconds vlan vlan-id Syntax set igmp oqi seconds vlan vlan-id Set igmp oqiAll VLANs on a WX Set igmp qi Set igmpProxy-report WX1200# set igmp qi 100 vlan orange success change accepted Set igmp qriVLANs on a WX Group. You can specify a value from 1 through 65,535 WX1200# set igmp qri 50 vlan orange success change accepted Syntax set igmp querier enable disable vlan vlan-id See Also „ display igmp querier on Syntax set igmp receiver port port-listenable disable VLAN, MSS changes the robustness value for all VLANs Defaults The default robustness value for all VLANs isSet igmp rv Occurs on the network Security ACL Security ACL Commands Syntax clear security acl acl-name all editbuffer-index Clear security acl map Syntax clear security acl map acl-nameall vlan vlan-id Syntax commit security acl acl-nameall WX4400# clear security acl map all success change accepted Syntax display security acl editbuffer WX4400# commit security acl allWX4400# display security acl Syntax display security acl hits WX4400# display security acl editbuffer Syntax display security acl info acl-nameall editbuffer See Also „ hit-sample-rateon „ set security acl onWX4400# display security acl hits Syntax display security acl map acl-name Display security aclMap Security ACL is assigned WX4400# display security acl map acl111 Resource-usageACL acl111 is mapped Support for your Product on WX4400# display security acl resource-usage Output of display security acl resource-usage Output of display security acl resource-usage Syntax hit-sample-rate seconds Hit-sample-ratePackets filtered by the security ACL or hits Syntax rollback security acl acl-nameall Protocol, or IP, ICMP, TCP, or UDP packet information Set security acl By UDP packets By Icmp packetsBy TCP packets „ ip „ tcp „ udp „ icmp Set security acl Security ACL Commands WX4400# set security acl ip acl123 deny 192.168.2.11 WX4400# commit security acl all configuration accepted Defaults None Set security acl map Security ACL Commands Cryptography Commands by Usage To locate commands in this chapter based on their use Syntax crypto ca-certificate admin eap webaaa See Also „ display crypto ca-certificateon Syntax crypto certificate admin eap webaaa Examples The following command installs a certificate See Also display crypto key ssh on Syntax crypto generate key admin eap ssh webaaa 512 1024WX4400# crypto generate key admin 1024 key pair generated Syntax crypto generate request admin eap webaaa Email Address admin@example.com WX4400# crypto generate request admin See Also „ crypto certificate on „ crypto generate key on Syntax crypto generate self-signed admin eap webaaa WX4400# crypto generate self-signed admin Crypto otp „ crypto pkcs12 on Crypto pkcs12 See Also „ crypto otp on Display crypto ca-certificate Output Display cryptoCa-certificate Pkcs #7 certificate Describes the fields of the display On the WX switchSyntax display crypto certificate admin eap webaaa Certificate Syntax display crypto key ssh See Also crypto generate key on Cryptography Commands Radius Commands by Usage Locate commands in this chapter based on their uses Clear radius Syntax clear radius client system-ip WX4400# clear radius timeout success change acceptedSee Also „ display aaa on „ set radius client system-ipon Syntax clear server group group-nameload-balance See Also „ display aaa on „ set radius server onSyntax clear radius server server-name WX4400# clear radius server rs42 success change accepted „ set server group on Set radius „ clear radius server on Set radius clientSystem-ip WX4400# set radius client system-ip success change accepted Radius and Server Group Commands Syntax set server group group-namemembers server-name1 „ group-name- Server group name of up to 32 characters Load-balance group Set server group load-balance Radius and Server Group Commands Performance On the switchCommands on 802.1X Commands by Usage Bonded-period Which disables the featureExamples To reset the Bonded period to its default, type Clear dot1x „ set dot1x max-reqon Port-controlSee Also „ display dot1x on „ set dot1x bonded-periodon See Also „ display dot1x on „ set dot1x quiet-periodon Quiet-period„ set dot1x port-controlon See Also „ display dot1x on „ set dot1x reauth-periodon Reauth-maxReauth-period „ set dot1x reauth-maxon Before the WX times out a request to a Radius server Defaults The default is 30 secondsAuthentication server, type the following command Auth-server „ set dot1x tx-periodon „ set dot1x timeout supplicant onTx-period Display dot1x WX4400# display dot1x clients WX1200# display dot1x config WX4400# display dot1x stats Type the following command to display 802.1X statisticsExplains the counters in the display dot1x stats output Authcontrol Port-control commandSet dot1x Machine to start reauthentication for the user Authentication is enabledExamples To enable per-port 802.1X authentication on wired Authentication ports, type the following command WX4400# set dot1x bonded-period 60 success change accepted Syntax set dot1x key-tx enable disableWX4400# set dot1x key-tx enable See Also „ display dot1x on „ clear dot1x bonded-periodon „ clear dot1x max-reqon Set dot1x max-req Syntax set dot1x quiet-period seconds To a supplicant after a failed authenticationSee Also „ display port status on „ display dot1x on Syntax set dot1x reauth enable disable Syntax set dot1x reauth-max number-of-attempts Attempts reauthenticationBefore the supplicant client becomes unauthorized See Also „ display dot1x on „ clear dot1x reauth-maxon Supplicant Set dot1x timeoutOut a request to a Radius authentication server Out an authentication session with a supplicant client Syntax set dot1x tx-period seconds See Also „ display dot1x on „ clear dot1x tx-periodon Wep-rekey-period Wep-rekey See Also „ display dot1x on „ set dot1x wep-rekeyon Telnet sessions Clear sessions Users NetworkVLANs, or session ID WX1200# clear sessions network user Natasha To clear session 9, type the following commandWX4400# clear sessions network mac-addr WX1200# clear sessions network session-id Display sessions WX4400 display sessions telnet WX4400 display sessions adminWX4400 display sessions console Display sessions telnet client Output See Also „ clear sessions on Syntax display sessions network WX1200# display sessions network mac-addr 00055d7e981a „ Summary display See on „ Verbose display See on„ display sessions network session-id display See on WX1200# display sessions network WX1200# display sessions network session-id WX1200# display sessions network verbose Additional display sessions network verbose Output Display sessions network summary Output Time Display sessions network session-id Output 802.1X protocol on a wired authentication port See Also „ clear sessions network on Session Management Commands RF Detection Commands Countermeasures Countermeasures mac commandRfdetect countermeasures mac commands Clear rfdetect Syntax clear rfdetect ignore mac-addr Ignore Syntax display rfdetect countermeasures Display rfdetectMobility Domain Domain Syntax display rfdetect data Radios as well as by third-party access points WX1200# display rfdetect data Display rfdetect data Output „ clear rfdetect ignore on Display rfdetect data command on that switchRadios, use the display rfdetect data command Ignore list WX1200# display rfdetect mobility-domain Display rfdetect mobility-domain Output Display neighboring BSSIDs Third-party access points„ mac-addr- Base MAC address of the 3Com radio To display the base MAC address of a 3Com radio, use WX1200# display rfdetect Visible ap Radio Display rfdetect visible OutputWX1200# display rfdetect visible 000b0e000a6a Set rf detect Set rfdetectActive-scan Syntax set rfdetect countermeasures mac mac-addr Set rfdetect countermeasures macStarts countermeasures against a specific rogue Syntax set rfdetect ignore mac-addr See Also „ display log buffer on Detected or when they disappearSyntax set rfdetect log enable disable Set rfdetect log File Management Commands History BackupDefaults All Tape archive tar format Describes the fields in the dir output Output for backupSyntax clear boot config Copy „ reset system on WX4400# copy floorwx tftp//10.1.1.1/floorwx Syntax delete url File or the running configurationDelete Immediately deletes the specified file WX4400# delete dang/dangdoc success file deleted Dir Following command displays the files in the old subdirectory Output for dir Display bootBoot „ copy on „ area area Configuration area. You can specify one Display configDescribes the fields in the display boot output Displays the configuration running on the WX switch WX4400# display config area vlan See Also „ load config on Display version „ save config onAnd, optionally, for any attached MAP access points Output for display version Describes the fields in the display version output Syntax load config url Load configRunning configuration with the commands in the loaded file Creates a new subdirectory in nonvolatile storage Following command loads configuration file testconfig1Mkdir „ dir on „ rmdir on WX4400# reset system Reset systemRestarts an WX switch and reboots the software Syntax reset system force Or restoring an archive RestoreKey pairs and certificates on the switch „ dir on „ mkdir on Save config„ backup on Rmdir Testconfig1 Set bootConfiguration-file Configuration Syntax set boot partition boot0 boot1 File Management Commands Syntax clear log trace Clear log traceDeletes the log messages stored in the trace buffer „ set log on Deletes running trace commands and ends trace processesClear trace WX4400# display trace WX switch, or all possible trace optionsDisplay trace Syntax display trace all Set trace AuthenticationSave trace Authorization for MAC address AuthorizationAbout user jose’s authentication Traces authorization information See Also „ clear trace on „ display trace on Set trace dot1x Syntax set trace sm mac-addr mac-address port port-num Set trace sm Trace Commands Syntax clear log buffer server ip-addr Clear log WX4400# clear log buffer success change accepted See Also „ clear log trace on WX4400# display log buffer facility AAA You can view event messages archived in the bufferLog buffer facility ? „ set log on „ clear log on „ display log config onLog config „ clear log on Syntax display log trace +-/number-of-messages Set log „ trace Sets log parameters for trace files „ Logging state enabled or disabled„ enable Enables messages to the specified target Mbytes Set log trace WX4400# set log trace mbytes 4 success change accepted See Also „ display log config on System LOG Commands Boot Prompt Boot Prompt Commands Autoboot „ FN=filename System image filename Boot„ BT=type Boot type „ DEV=device Location of the system image file „ change on „ display on Syntax change Change Syntax create Create Syntax delete Usage When you type the delete command, the next-lowerExamples To remove the currently active boot profile, type Profiles, see display on Syntax diag Diag „ fver on „ version on Syntax display Defaults None „ change on „ create on „ delete on „ next on Output of display command Fver „ ls on For an individual command„ command-name- Boot prompt command Displays a list of the boot prompt commands Next Syntax next Defaults None Command at the boot prompt ResetResets a WX switch’s hardware Syntax reset Test „ on Enables the poweron test flag„ OFF Disables the poweron test flag Defaults The poweron test flag is disabled by default Boot version Syntax version Defaults NoneDir or fver command Type the following command at the boot prompt „ dir on „ fver on Boot Prompt Commands Purchase ServicesRegister Your Product Downloads Access SoftwareTroubleshoot Online Contact Us Need to apply for a user name and password Latsupportanc@3com.com Country Telephone Number Index Delete 474, 515 diag Dir 475, 516 disable 33 display Index Index Index Index