Display rfdetect mobility-domain Output | 3Com 3CRWX440095A specification

462CHAPTER 17: RF DETECTION COMMANDS

Examples — The following example displays information about the

BSSIDs detected in the Mobility Domain managed by the seed switch:

WX1200# display rfdetect mobility-domain
Total number of entries: 3		Port/Radio	RSSI	SSID
BSSID	WX-IPaddr
> Radio Mac		/Channel		-----------
----------------------	--------------- ------------- ----
00:00:00:01:7a:80	10.8.121.101	5/2/60	-34	wla
> 00:0b:0e:00:0a:a3
> 00:0b:0e:00:04:c8	10.8.121.101	4/2/60	-46	wla
> 00:0b:0e:00:0a:6b	10.8.121.102	3/2/60	-32	wlay
00:00:00:01:d1:41	10.8.121.101	4/2/36	-37	wla
> 00:0b:0e:00:04:c8
> 00:0b:0e:00:0a:a3	10.8.121.101	5/2/36	-33	wla
00:00:00:01:d9:41	10.8.121.101	5/2/52	-66	public
> 00:0b:0e:00:0a:a3
> 00:0b:0e:00:0a:6b	10.8.121.102	3/2/52	-54	public

Table 88 describes the fields in this display.

Table 88 display rfdetect mobility-domain Output

Field	Description

BSSID > Radio MAC	MAC address of the SSID advertised by the detected device,
	and the MAC addresses of the radios that detected the
	BSSID.
	The BSSID is listed first. The MAC addresses of the 3Com
	radios that detected the BSSID are listed underneath the
	BSSID.
	If a 3Com radio is supporting more than one SSID, each of
	the corresponding BSSIDs is listed separately.

WX-IPaddr	System IP address of the WX switch that is managing the
	MAP that detected the rogue.

Port/Radio/Channel	Port number, radio number, and channel number of the
	radio that detected the rogue. For a Distributed MAP, the
	connection number is labeled dap. (This stands for
	distributed ap.)

RSSI	Received signal strength indication (RSSI) — the strength of
	the RF signal detected by the MAP radio, in decibels referred
	to 1 milliwatt (dBm).

SSID	Service set identifier (SSID) associated with the BSSID.

Image 462

3Com 3CRWX440095A, 3CRWX120695A manual Display rfdetect mobility-domain Output, WX1200# display rfdetect mobility-domain

Contents

Wireless LAN Mobility System 3CRWX120695A, 3CRWX440095A 3Com Corporation 350 Campus Drive Marlborough, MA USA Contents Clear banner motd Clear history Clear prompt Set system location Vlan Commands 144 131 Ping 132 Set arp 133 Set arp agingtime 134142 Set ip ssh 143 147 Set ntp 148 169 183Display location policy 185 Display mobility-profile 234 MAP Access Point Commands by Usage228 241 254 Display dap unconfigured 256 Display radio-profile 257 261 Reset ap dap 264 326 311319 327 337 335Set spantree 345 Clear security acl 370 Clear security acl map 371 Commands by Usage 393369 373 435 444446 Set rfdetect ignore 467 Set rfdetect log 468 465 Set rf detect countermeasures466 480 496 Set trace sm 497 Commands by Usage 491 Clear log trace Clear trace 492Fver 519 Help 520 Next 521 Reset 522 Test 523 517 Version Register Your Product 527 Conventions List conventions that are used throughout this guide „ Wireless LAN Switch Manager 3WXM Release Notes „ Wireless LAN Switch and Controller Release NotesDocumentation „ Document title CommentsPddtechpubscomments@3com.com „ Document part number and revision on the title About this Guide Overview Set enablepass Clear interface vlan-idipClear fdb dynamic port port-list vlan vlan-id MAC Address Text EntryConventions Notation Wildcard Masks MasksSubnet Masks User Globs Gives examples of user globs MAC Address GlobsUser Globs Matching Order for Globs WX1200# set port enableVlan Globs „ a single port number. For example Editing Command-LineWX1200# reset port Operating systems WX1200# display i Tab Using CLI Help At your access level, type the help command. For exampleWX1200# display i? WX1200# display ip ? Understanding Command DescriptionsSet ap dap name command has the following complete syntax WX1200# display ip telnet Understanding Command Descriptions Using the COMMAND-LINE Interface To located commands in this chapter based on their use Commands byDisable Syntax disable Defaults None Enable Quit Set enablepass Access Commands System Service Commands To located commands in this chapter based on their use Clear history Banner with an empty banner by typing the following commandClear banner motd „ display banner motd on Clear prompt Clear system Display banner Motd Display Base-informationDisplay license „ set license on Defaults None Access AllDisplay system Shows system information Describes the fields of display system output Display system output Nvram size /SDRAM size percent of total WX switch HelpSyntax help History Syntax historySee Also „ clear history on That might have a large impact on the network Set confirmSee Also „ clear banner motd on „ display banner motd on Syntax set confirm on off WX4400# clear vlan red Set lengthExamples To turn off these confirmation messages, type WX4400# set confirm off Installs an upgrade license, for managing more MAPs Set licenseSee Also „ display license on Set prompt Syntax set prompt string Countrycode Set system contact Stores a contact name for the WX switchSet system Syntax set system contact string Country Code Ip-address Defaults The factory default country code is NoneUsing any set ap commands to configure a MAP Mobility Domain See Also „ clear system on „ display system on Syntax set system location string „ set system contact on „ set system name on Syntax set system name string System Service Commands Port Commands Locate commands in this chapter based on their use Removes a Distributed MAP That are using the MAPClear dap „ set dap on See Also „ set port-groupon „ display port-groupon Clear port-group„ name name Name of the port group Clear port name Removes the name assigned to a port See Also „ display port status on „ set port name on Clear portPreference Interface for the active link Network port Network port defaultsClear port type Port Display port Counters Display port-groupShows port group information Describes the fields in the display port-group outputOutput for display port-group Output for display port poe See Also „ clear port-groupon „ set port-grouponDescribes the fields in this display Syntax display port poe port-list „ set port poe on Usage This command applies only to the WX4400All four ports of a WX4400 switch Specified ports Output for display port preference Syntax display port status port-list Output for display port status WX1200# display port status „ set port negotiation on Monitor portSee Also „ clear port type on „ set port speed on Key Controls for Monitor Port Counters Display Output for monitor port counters WX4400# monitor port counters Correct length but contained an invalid See Also „ display port counters on Reset port Set dap Port Commands Set dap Administratively disables or reenables a port Examples The following command disables portFol1owing command reenables the port Set port Configured together as a single logical link Single logical linkWith no spaces See Also „ clear port-groupon „ display port-groupon Name or number in other CLI commandsSet port name See Also „ clear port name on „ display port status on Set port negotiation Set port poeResult WX1200# set port poe 4,5 disable Following command enables PoE on ports 4See Also „ set port type ap on „ set port type wired-authon WX1200# set port poe 4,5 enable WX4400# set port preference 2 rj45 Set port speedChanges the speed of a port Syntax set port speed port-list10 100 1000 auto Set snmp trap command Set port trap Set port type ap Defaults All WX ports are network ports by default Antenna model, use the following command„ poe enable disable Power over Ethernet PoE state „ 11a 802.11a „ 11b 802.11b „ 11g 802.11g MAP Access Port Defaults STP Wired-auth Set port type Wired Authentication Port Details WX1200# set port type wired-auth 2 success change accepted See Also „ clear port type on „ set port type ap on Vlan Commands Syntax clear fdb perm static dynamic Clear fdbDeletes an entry from the forwarding database FDB WX4400# clear fdb static vlan blue success change accepted Clear vlan „ display fdb onPort from the VLAN, make sure you specify the port number Display fdb Following command completely removes Vlan marigoldSee Also „ set vlan port on „ display vlan config on Displays entries in the forwarding database WX4400# display fdb all See Also „ clear fdb on AgingtimeDescribes the fields in the display fdb output Output for display fdb See Also „ set fdb agingtime on WX1200# display fdb agingtimeSyntax display fdb count perm static dynamic Display roaming Station Describes the fields in the display See Also „ display roaming vlan onOutput for display roaming station Output for display roaming vlan Syntax display roaming vlanWX4400# display roaming vlan Output for display tunnel See Also „ display vlan config onDisplay tunnel Syntax display tunnel Syntax display vlan config vlan-id Display vlan configOutput for display vlan config WX1200# display vlan config burgundy Set fdb Adds a permanent or static entry to the forwarding databaseSyntax set fdb perm static See Also „ clear fdb on „ display fdb on Vlan 4094 is reserved for WebAAA Set vlan nameSee Also „ display fdb agingtime on Creates a Vlan and assigns a number and name to it Set vlan port Set vlan Tunnel-affinity See Also „ display roaming vlan on „ display vlan config on IP Services Commands To locate commands in this chapter based on their use IP Services Commands by Usage DNS Clear interface Removes an IP interfaceSyntax clear interface vlan-idip See Also „ display ip alias on Access EnabledHistory Introduced in MSS Version WX1200# clear ip dns domain „ set ip dns domain on Clear ip dns serverClear ip route „ set ip dns server on Clear ip telnet „ display ip route on„ set ip route on Update-interval Clear ntp serverClear ntp Receiver „ set ntp server on „ set ntp update-intervalonClear snmp trap See Also „ clear ntp server on „ display ntp on Clear summertime Clear timezone CommandFollowing command Examples To clear the system IP address, type the following Display timezone on Display arpDisplay timedate on Shows the ARP table „ set arp on „ set arp agingtime onSyntax display interface vlan-id See Also „ set interface on „ set interface status on Shows the IP aliases configured on the wireless LAN switchDisplay ip alias Output for display interface „ clear ip alias on Examples The following command displays the DNS informationDisplay ip dns „ set ip alias on Output for display ip dns Display ip httpsShows information about the Https management port Syntax display ip https Output for display ip https WX4400# display ip https Syntax display ip route destination Display ip routeShows the IP route table WX4400# display ip route Output of display ip route FieldDescription Output for display ip telnet Syntax display ip telnetWX4400 display ip telnet Shows NTP client information Examples To display NTP information for a WX switch, typeDisplay ntp Output for display ntp „ set ntp server on „ set summertime on „ set timezone on Examples To display Snmp settings on a WX switch, type ConfigurationShows Snmp settings on a wireless LAN switch Display snmp Output of display snmp configuration Syntax display summertime Defaults There is no summertime offset by defaultSummertime WX1200# display summertime WX1200# display timedate Syntax display timezoneWX4400# display timezone Defaults „ count „ set timedate on „ set timezone on Set arp „ traceroute on Syntax set arp agingtime seconds Following command disables ARP agingSee Also „ set arp agingtime on WX1200# set arp agingtime Set interface WX1200# set interface mauve ip 10.10.20.10 Syntax set interface vlan-idstatus up down Set ip dns Aliases as shortcuts in CLI commandsSet ip alias See Also „ clear ip alias on „ display ip alias on Syntax set ip dns domain name WX1200# set ip dns domain example.com Syntax set ip dns server ip-addrprimary secondary WX switch is also disabled Set ip routeAdds a static route to the IP route table Set ip route Syntax set ip snmp server enable disable „ clear snmp trap receiver on See Also „ set ip ssh absolute-timeoutonSet ip ssh Secure Shell SSH management traffic Syntax set ip ssh absolute-timeout minutes Absolute-timeout„ set ip ssh idle-timeouton „ set ip ssh server on Or idle Idle-timeout Also disabledSet ip ssh server Set ip telnet Syntax set ip telnet server enable disable WX4400# set ip telnet server enable success change accepted Configures a wireless LAN switch to use an NTP server Examples The following command enables the NTP clientEnables or disables the NTP client on a wireless LAN switch Set ntp NTP server RFC 1305, Network Time Protocol Version 3 SpecificationImplementation and Analysis From 16 through 1,024 seconds Set snmp CommunityPublic and private „ all Enables or disables all traps „ enable Enables trap information to be sent„ disable Disables the sending of trap information Sends an Snmp trap message to any network management system Defaults All traps are disabled by default Access Enabled Snmp Trap Names Set snmp trap See Also „ clear snmp trap receiver on IP Services Commands Date is within the summertime period To PDT Pacific Daylight Time, type the following commandValues Following „ date mmm dd yyyy System date Sets the time of day and date on the wireless LAN switchSet timedate „ time hhmmss System time, in hours, minutes, and seconds Set timezone WX4400# set timedate date feb 29 2004 timeTime now is Sun Feb 29 2004, 235802 PST Telnet Opens a Telnet client session with a remote deviceWX1200# set timezone PST See Also „ clear sessions on „ display sessions on WX4400# telnet Traceroute Defaults„ dnf Disabled „ no-dns- Disabled „ port „ queries „ size „ ttl Error messages for traceroute WX4400# traceroute server1 „ ping on Locate commands in this chapter based on their use This chapter presents AAA commands alphabetically. Use toAAA Commands by Usage Display accounting statistics on Syntax clear accounting admin dot1x user-glob WX4400# clear accounting dot1x Nin Clear authentication Admin Syntax clear authentication console user-glob WX4400# clear authentication console ReginaConsoleConsole Syntax clear authentication dot1x ssid ssid-namewired WX4400# clear authentication last-resort wired Clear authentication Removes a MAC authentication rule. macSyntax clear authentication last-resort ssid ssid-namewired Syntax clear authentication mac ssid ssid-namewired Clear authentication Removes a WebAAA rule. web WX4400# clear authentication mac ssid thatcorp aabbccSyntax clear authentication web ssid ssid-namewired Syntax clear location policy rule-number „ set location policy on Clear mac-user„ display location policy on See Also „ display aaa on „ set mac-usergroup attr on Clear mac-user attr Group„ set mac-user attr on Clear Mac-usergroup Mac-user group command Mac-usergroup attr„ clear mac-usergroup attr on Mobility-profile Clear user Clear user attr See Also „ display aaa on Clear user group Clear usergroup „ group-name- Name of an existing user group Syntax clear usergroup group-nameWX4400# clear usergroup cardiology success change accepted Displays all current AAA settings Display aaaTime-Of-Day attribute from the group Describes the fields that can appear in display aaa output Display aaa Output User’s password, and no global password is set Statistics Stored in the local database on the WX switchDisplay accounting Statistics output Aaattyattr Display location Policy„ clear location policy on Admin console Set accountingAre sent Authenticated by Server when the user roamsAccesses the switch using Telnet or Web Manager Authenticated by MAC authentication AAA Commands Set authentication AAA Commands Globs on Through the switch’s consoleCompleting logon Following methods in priority order. MSS applies multiple For more information, see Usage Syntax set authentication dot1x ssid ssid-namewired AAA Commands Set authentication dot1x Success change accepted Syntax set authentication last-resort AAA Commands Syntax set authentication mac AAA Commands Syntax set authentication web ssid ssid-namewired AAA Commands Set location policy AAA Commands Set location policy WX4400# set location policy deny if user eq *.theirfirm.com Set mac-user Tempvendora into Vlan kiosk1 See Also „ clear mac-useron „ display aaa on Authentication Attributes for Local Users Authentication Attributes for Local Users Filter-id outboundacl.out YY/MM/DD-HHMM Time-of-day WX4400# set mac-user 010203040506 attr filter-id acl-03.in See Also „ clear mac-user attr on „ display aaa on Syntax set mac-usergroup See Also „ clear mac-usergroup attr on „ display aaa on Syntax set mobility-profile name name port none all AAA Commands Syntax set mobility-profile mode enable disable „ set user attr on „ set usergroup on Set user 29Jan04See Also „ clear user on „ display aaa on Set user attr OrangeSee Also „ clear user attr on „ display aaa on Set user group Set usergroup„ clear user group on To add a user to a group, user the command set user group Syntax set web-aaa enable disableSet web-aaa Examples To disable WebAAA, type the following command WX4400# set web-aaa disable success change accepted To locate commands in this chapter based on their use Mobility Domain Commands by Usage Mobility-domain Member Status Display mobility-domain configDisplays the configuration of the Mobility Domain See Also „ set mobility-domain member on Display mobility-domain Output WX4400# display mobility-domain status Set Mode member„ display mobility-domain config on Seed-ip Set mobility-domain mode seed domain-name Syntax set mobility-domain mode seed domain-name Domain name is Pleasanton Mobility Domain Commands Commands Managed Access Point Commands Map Access Point Commands by Usage Clear ap dap Radio WX1200# clear ap 3 radio Syntax clear radio-profile name parameter „ name Service profile name Syntax clear service-profile name See Also „ clear radio-profileon „ set radio-profile mode on Output for display ap config WX1200# display ap configWX4400# display dap config Does not belong to any load balancing groups An associated client Display ap dap Displays MAP access point and radio statistics countersMAP access point on port Radio 1 Shows statistics counters for radio Output for display ap counters Tkip Pkt Replays See Also „ display sessions network on Syntax display ap dap etherstats port-listdap-numWX4400# display dap etherstats Output of display ap etherstats TxMaxColl „ name Name of an MAP group or Distributed MAP group Syntax Syntax display ap status port-listall radio 1 WX4400# display dap status WX1200# display ap status Output for display ap status Decide whether to change channel or power settings Output for display ap status See Also „ display auto-tune neighbors on Output for display auto-tune attributesWX1200# display auto-tune attributes ap 2 radio Display auto-tune Neighbors Output for display auto-tune neighbors Display auto-tune Neighbors ap 2 radio Display dap Connection Output of display dap connection „ display ap dap config on„ display dap global on „ display dap unconfigured on Dap connection serial-id M9DE48B6EAD00 Output for display dap global WX4400# display dap global But that are not configured on any WX switches Unconfigured„ display ap dap config on Longer appears in the command’s output Describes the fields in this display Displays radio profile information WX4400# display radio-profile default Output for display radio-profile Setting and tuning channels Ssid „ name Displays information about the named service profile Service-profileDisplays service profile information „ ? Displays a list of service profiles Username „ Tkip countermeasures time Indicates the amount Reset ap dap WX1200# reset apSyntax set ap port-listdap dap-numbias high low See Also „ display ap dap config on WX4400# set dap 1 bias low success change accepted Syntax set ap port-listdap dap-numblink enable disable WX1200# set ap 3-4 blink enable success change accepted WX1200# set ap 4 group none success change accepted Set ap dap name Changes an MAP name„ display ap dap group on WX1200# set ap 1 name techpubs success change accepted Set ap dap radio antennatype „ antennatype ANT1060 ANT1120 ANT1180 internal„ antennatype ANT5060 ANT5120 ANT5180 internal Set ap dap radio auto-tune max-power Set ap dap radio auto-tune max- retransmissions Managed Access Point Commands Set ap dap radio channel Sets an MAP radio’s channelSyntax set ap port-listdap dap-numradio 1 Set ap dap radio min-client-rate WX1200# set ap 5 radio 1 channel 36 success change accepted Set ap dap radio min-client-rate Set ap dap radio mode Enables or disables a radio on an MAP access pointFollowing command enables radio 2 on ports 1 through Set ap dap radio radio-profile Set ap dap radio tx-power Sets an MAP radio’s transmit power Upgrade-firmware Set ap dap Set radio-profile 11g-only Set radio-profile auto-tune channel-config Set radio-profile auto-tune channel-holddown Syntax set radio-profile name auto-tune channel-holddown Set radio-profile auto-tune channel-interval Syntax set radio-profile name auto-tune channel-interval Set radio-profile auto-tune power-backoff- timer Syntax set radio-profile name auto-tune power-backoff-timerWX4400# set radio-profile rp2 auto-tune power-backoff-timer Set radio-profile auto-tune power-config Set radio-profile auto-tune power-interval Specify from 25 ms to 8191 ms Service set identifier SsidBeacon-interval Radio profile rp1 to 200 ms Syntax set radio-profile name frag-threshold threshold Syntax set radio-profile name long-retry threshold Syntax set radio-profile name max-rx-lifetime time Max-tx-lifetime Mode Defaults for Radio Profile Parameters Parameter Default Value WX4400# set radio-profile rp1 mode enable WX4400# set radio-profile rp1 success change accepted Syntax set radio-profile name Syntax set radio-profile name rts-threshold threshold Defaults for Service Profile Parameters Syntax set radio-profile name service-profile name 297 Defaults for Service Profile Parameters Syntax set radio-profile name short-retry threshold Syntax set service-profile Name auth-dot1x enable disable WPA IE Set service-profile auth-fallthru Syntax set service-profile name auth-psk enable disable Syntax set service-profile name beaconed enable disable Set service-profile Cipher-ccmp Cipher-tkip Use the set service-profile wep commands See Also „ set service-profilecipher-ccmponCipher-wep104 Defaults 40-bit WEP encryption is disabled by default „ enable Enables 40-bit WEP encryption for WPA clients„ disable Disables 40-bit WEP encryption for WPA clients Cipher-wep104 command Syntax set service-profile name psk-phrase passphrase Syntax set service-profile name psk-raw hex Syntax set service-profile name rsn-ie enable disable Set service-profile auth-psk command Syntax set service-profile name ssid-name ssid-name See Also „ set service-profilessid-typeon See Also „ set service-profilessid-nameon Syntax set service-profile name tkip-mc-time wait-time Ssid managed by the service profile Syntax set service-profile name web-aaa-form urlWeb-aaa-form Set service-profile wep active-multicast- index „ copy on „ dir on„ mkdir on Set service-profile wep active-unicast- index Syntax set service-profile name wep active-unicast-index num Wep key-index Syntax set service-profile name wpa-ie enable disable STP Commands by Table to locate commands in this chapter based on their useSTP Commands by Usage Portcost STP root bridge in all VLANs on a WX switchClear spantree Syntax clear spantree portcost port-list „ clear spantree portvlanpri on PortpriPortvlancost „ set spantree portpri on Portvlanpri „ clear spantree portcost on „ clear spantree portpri on See Also „ display spantree statistics on Spantree vlan default Syntax display spantree Output for display spantree Root Backbonefast Or disabledDisplay spantree „ display spantree blockedports on „ set spantree backbonefast on WX switch with backbone fast convergence enabledBlockedports One or all of its VLANs See Also „ set spantree portfast on PortfastFor one or more network ports Output for display spantree portfast Syntax display spantree portvlancost port-list Port’s VLANs„ port-list- List of ports Syntax display spantree statistics WX4400# display spantree statistics Topology change Timer value Hold timer Output for display spantree statistics Vlan Vlan ID Configpending Switch is the root or is attempting to become the root See Also „ clear spantree statistics on Syntax display spantree uplinkfast vlan vlan-id Set spantree „ set spantree uplinkfast on Following command disables STP on Vlan burgundy Examples The following command enables STP on all VLANsConfigured on a WX switch An indirect link Fwddelay „ display spantree backbonefast on VLANs to 4 seconds Issues a topology change messageMaxage „ all Changes the maximum age on all VLANs Path to the STP root bridge Type. lists the defaults for STP port path costSnmp Port Path Cost Defaults 65,535. STP selects lower-cost paths over higher-cost paths Portvlancost command See Also „ display spantree portfast on Syntax set spantree portpri port-listpriority value Type. See on Bridge for a specific Vlan on a wireless LAN switch„ all Changes the cost on all VLANs To 20 in Vlan mauve Priority Pink to Uplinkfast32,768 Primary link fails See Also „ display spantree uplinkfast on Igmp Snooping Commands Igmp Commands by Usage Clear igmp statistics Display igmpSee Also display igmp statistics on TTL Output for display igmp TTL Mrouter Syntax display igmp mrouter vlan vlan-idWX1200# display igmp Mrouter vlan orange Defaults None Access Enabled Only one querierSyntax display igmp querier vlan vlan-id WX1200# display igmp querier vlan orange WX1200# display igmp querier vlan defaultOutput for display igmp mrouter WX1200# display igmp querier vlan red Receiver-table „ set igmp querier on VLAN, MSS displays Igmp statistics for all VLANs See Also „ set igmp receiver onShows Igmp statistics WX1200# display igmp receiver-table group 237.255.255.0/24 WX1200# display igmp statistics vlan orange Output of display igmp statistics From the multicast routers in the subnet Wireless LAN switch See Also „ set igmp rv on Set igmp lmqi VLANs on a wireless LAN switchVLAN, the timer change applies to all VLANs From 1 through 65,535 Set igmp mrsol Enables or disables multicast router solicitation by a WXSyntax set igmp mrsol enable disable vlan vlan-id See Also „ display igmp statistics on Syntax set igmp mrsol mrsi seconds vlan vlan-id See Also „ set igmp mrsol mrsi onSee Also „ set igmp mrsol on WX1200# set igmp mrsol mrsi 60 success change accepted Set igmp oqi All VLANs on a WXSyntax set igmp oqi seconds vlan vlan-id Set igmp Proxy-reportSet igmp qi Group. You can specify a value from 1 through 65,535 Set igmp qriVLANs on a WX WX1200# set igmp qi 100 vlan orange success change accepted Syntax set igmp querier enable disable vlan vlan-id WX1200# set igmp qri 50 vlan orange success change accepted Syntax set igmp receiver port port-listenable disable See Also „ display igmp querier on Occurs on the network Defaults The default robustness value for all VLANs isSet igmp rv VLAN, MSS changes the robustness value for all VLANs Security ACL Commands Security ACL Syntax clear security acl acl-name all editbuffer-index Clear security acl map Syntax clear security acl map acl-nameall vlan vlan-id WX4400# clear security acl map all success change accepted Syntax commit security acl acl-nameall WX4400# commit security acl all WX4400# display security aclSyntax display security acl editbuffer WX4400# display security acl editbuffer Syntax display security acl hits See Also „ hit-sample-rateon „ set security acl on WX4400# display security acl hitsSyntax display security acl info acl-nameall editbuffer Security ACL is assigned Display security aclMap Syntax display security acl map acl-name Support for your Product on Resource-usageACL acl111 is mapped WX4400# display security acl map acl111 WX4400# display security acl resource-usage Output of display security acl resource-usage Output of display security acl resource-usage Hit-sample-rate Packets filtered by the security ACL or hitsSyntax hit-sample-rate seconds Syntax rollback security acl acl-nameall Set security acl Protocol, or IP, ICMP, TCP, or UDP packet information By Icmp packets By TCP packetsBy UDP packets „ ip „ tcp „ udp „ icmp Set security acl Security ACL Commands WX4400# commit security acl all configuration accepted WX4400# set security acl ip acl123 deny 192.168.2.11 Defaults None Set security acl map Security ACL Commands To locate commands in this chapter based on their use Cryptography Commands by Usage Syntax crypto ca-certificate admin eap webaaa Syntax crypto certificate admin eap webaaa See Also „ display crypto ca-certificateon Examples The following command installs a certificate Syntax crypto generate key admin eap ssh webaaa 512 1024 WX4400# crypto generate key admin 1024 key pair generatedSee Also display crypto key ssh on Syntax crypto generate request admin eap webaaa WX4400# crypto generate request admin Email Address admin@example.com Syntax crypto generate self-signed admin eap webaaa See Also „ crypto certificate on „ crypto generate key on WX4400# crypto generate self-signed admin Crypto otp Crypto pkcs12 „ crypto pkcs12 on See Also „ crypto otp on Pkcs #7 certificate Display cryptoCa-certificate Display crypto ca-certificate Output Certificate On the WX switchSyntax display crypto certificate admin eap webaaa Describes the fields of the display See Also crypto generate key on Syntax display crypto key ssh Cryptography Commands Locate commands in this chapter based on their uses Radius Commands by Usage Clear radius WX4400# clear radius timeout success change accepted See Also „ display aaa on „ set radius client system-iponSyntax clear radius client system-ip WX4400# clear radius server rs42 success change accepted See Also „ display aaa on „ set radius server onSyntax clear radius server server-name Syntax clear server group group-nameload-balance Set radius „ set server group on Set radius client System-ip„ clear radius server on WX4400# set radius client system-ip success change accepted Radius and Server Group Commands Syntax set server group group-namemembers server-name1 Load-balance group „ group-name- Server group name of up to 32 characters Set server group load-balance Radius and Server Group Commands 802.1X Commands by Usage On the switchCommands on Performance Clear dot1x Which disables the featureExamples To reset the Bonded period to its default, type Bonded-period Port-control See Also „ display dot1x on „ set dot1x bonded-periodon„ set dot1x max-reqon Quiet-period „ set dot1x port-controlonSee Also „ display dot1x on „ set dot1x quiet-periodon „ set dot1x reauth-maxon Reauth-maxReauth-period See Also „ display dot1x on „ set dot1x reauth-periodon Auth-server Defaults The default is 30 secondsAuthentication server, type the following command Before the WX times out a request to a Radius server Display dot1x „ set dot1x timeout supplicant onTx-period „ set dot1x tx-periodon WX1200# display dot1x config WX4400# display dot1x clients Type the following command to display 802.1X statistics Explains the counters in the display dot1x stats outputWX4400# display dot1x stats Port-control command Set dot1xAuthcontrol Authentication ports, type the following command Authentication is enabledExamples To enable per-port 802.1X authentication on wired Machine to start reauthentication for the user See Also „ display dot1x on „ clear dot1x bonded-periodon Syntax set dot1x key-tx enable disableWX4400# set dot1x key-tx enable WX4400# set dot1x bonded-period 60 success change accepted Set dot1x max-req „ clear dot1x max-reqon To a supplicant after a failed authentication See Also „ display port status on „ display dot1x onSyntax set dot1x quiet-period seconds Syntax set dot1x reauth enable disable See Also „ display dot1x on „ clear dot1x reauth-maxon Attempts reauthenticationBefore the supplicant client becomes unauthorized Syntax set dot1x reauth-max number-of-attempts Out an authentication session with a supplicant client Set dot1x timeoutOut a request to a Radius authentication server Supplicant See Also „ display dot1x on „ clear dot1x tx-periodon Syntax set dot1x tx-period seconds Wep-rekey Wep-rekey-period See Also „ display dot1x on „ set dot1x wep-rekeyon Clear sessions Telnet sessions Network VLANs, or session IDUsers WX1200# clear sessions network session-id To clear session 9, type the following commandWX4400# clear sessions network mac-addr WX1200# clear sessions network user Natasha Display sessions WX4400 display sessions admin WX4400 display sessions consoleWX4400 display sessions telnet See Also „ clear sessions on Display sessions telnet client Output Syntax display sessions network WX1200# display sessions network „ Summary display See on „ Verbose display See on„ display sessions network session-id display See on WX1200# display sessions network mac-addr 00055d7e981a WX1200# display sessions network verbose WX1200# display sessions network session-id Display sessions network summary Output Additional display sessions network verbose Output Time 802.1X protocol on a wired authentication port Display sessions network session-id Output See Also „ clear sessions network on Session Management Commands RF Detection Commands Clear rfdetect Countermeasures mac commandRfdetect countermeasures mac commands Countermeasures Ignore Syntax clear rfdetect ignore mac-addr Domain Display rfdetectMobility Domain Syntax display rfdetect countermeasures Radios as well as by third-party access points Syntax display rfdetect data Display rfdetect data Output WX1200# display rfdetect data Ignore list Display rfdetect data command on that switchRadios, use the display rfdetect data command „ clear rfdetect ignore on Display rfdetect mobility-domain Output WX1200# display rfdetect mobility-domain To display the base MAC address of a 3Com radio, use Third-party access points„ mac-addr- Base MAC address of the 3Com radio Display neighboring BSSIDs Display rfdetect visible Output WX1200# display rfdetect visible 000b0e000a6aWX1200# display rfdetect Visible ap Radio Set rfdetect Active-scanSet rf detect Set rfdetect countermeasures mac Starts countermeasures against a specific rogueSyntax set rfdetect countermeasures mac mac-addr Syntax set rfdetect ignore mac-addr Set rfdetect log Detected or when they disappearSyntax set rfdetect log enable disable See Also „ display log buffer on File Management Commands Tape archive tar format BackupDefaults All History Output for backup Syntax clear boot configDescribes the fields in the dir output „ reset system on Copy WX4400# copy floorwx tftp//10.1.1.1/floorwx Immediately deletes the specified file File or the running configurationDelete Syntax delete url Dir WX4400# delete dang/dangdoc success file deleted Following command displays the files in the old subdirectory „ copy on Display bootBoot Output for dir Displays the configuration running on the WX switch Display configDescribes the fields in the display boot output „ area area Configuration area. You can specify one See Also „ load config on WX4400# display config area vlan „ save config on And, optionally, for any attached MAP access pointsDisplay version Describes the fields in the display version output Output for display version Load config Running configuration with the commands in the loaded fileSyntax load config url Following command loads configuration file testconfig1 MkdirCreates a new subdirectory in nonvolatile storage „ dir on „ rmdir on Syntax reset system force Reset systemRestarts an WX switch and reboots the software WX4400# reset system Restore Key pairs and certificates on the switchOr restoring an archive Rmdir Save config„ backup on „ dir on „ mkdir on Configuration Set bootConfiguration-file Testconfig1 Syntax set boot partition boot0 boot1 File Management Commands Clear log trace Deletes the log messages stored in the trace bufferSyntax clear log trace Deletes running trace commands and ends trace processes Clear trace„ set log on Syntax display trace all WX switch, or all possible trace optionsDisplay trace WX4400# display trace Authentication Save traceSet trace Traces authorization information AuthorizationAbout user jose’s authentication Authorization for MAC address Set trace dot1x See Also „ clear trace on „ display trace on Set trace sm Syntax set trace sm mac-addr mac-address port port-num Trace Commands Clear log Syntax clear log buffer server ip-addr See Also „ clear log trace on WX4400# clear log buffer success change accepted You can view event messages archived in the buffer Log buffer facility ?WX4400# display log buffer facility AAA „ clear log on „ display log config onLog config „ set log on „ clear log on Syntax display log trace +-/number-of-messages Set log „ Logging state enabled or disabled „ enable Enables messages to the specified target„ trace Sets log parameters for trace files Set log trace Mbytes See Also „ display log config on WX4400# set log trace mbytes 4 success change accepted System LOG Commands Boot Prompt Commands Boot Prompt Autoboot „ DEV=device Location of the system image file Boot„ BT=type Boot type „ FN=filename System image filename „ change on „ display on Change Syntax change Create Syntax create Profiles, see display on Usage When you type the delete command, the next-lowerExamples To remove the currently active boot profile, type Syntax delete Diag Syntax diag Syntax display Defaults None „ fver on „ version on Output of display command „ change on „ create on „ delete on „ next on Fver Displays a list of the boot prompt commands For an individual command„ command-name- Boot prompt command „ ls on Syntax next Defaults None Next Syntax reset ResetResets a WX switch’s hardware Command at the boot prompt Defaults The poweron test flag is disabled by default „ on Enables the poweron test flag„ OFF Disables the poweron test flag Test Type the following command at the boot prompt Syntax version Defaults NoneDir or fver command Boot version „ dir on „ fver on Boot Prompt Commands Product ServicesRegister Your Purchase Online Access SoftwareTroubleshoot Downloads Need to apply for a user name and password Contact Us Country Telephone Number Latsupportanc@3com.com Index Delete 474, 515 diag Dir 475, 516 disable 33 display Index Index Index Index