Cisco Systems A9014CFD manual Example When 10gigUpgrade License is not Installed

Chapter 2 Licensing

Port or Interface Behavior

Installing licenses from "flash:FHAK13101A1_20110811190230024_fls-a901-4t.lic"

Installing...Feature:Fls-a901-4t...Successful:Supported

1/1 licenses		were successfully installed
0/1	licenses	were	existing licenses
0/1	licenses	were	failed to install
Router#*Oct		5 17:23:14.487: %LICENSE-6-INSTALL: Feature Fls-a901-4t 1.0		was installed in
this device.		UDI=MWR-3941-TEST:FHAK13101A1; StoreIndex=2:Primary License		Storage

Router(config)# interface gig 0/0

Router(config-if)# no shutdown

When the port based license is installed for copper or SFP ports, the corresponding ports are enabled. Following is a sample output from the show ip interface command:

	Router# show ip interface brief
	Interface	IP-Address	OK? Method	Status	Protocol
	GigabitEthernet0/0	unassigned	YES unset	up	up
	GigabitEthernet0/1	unassigned	YES unset	administratively down down
	GigabitEthernet0/2	unassigned	YES unset	administratively down down
	…..
Note	Combo ports are either copper or SFP ports depending on the configuration specified in the media-type
	command.

10gigUpgrade License

When you do not have the 10gigUpgrade license, the 10 Gigabit Ethernet ports are enabled in 1 Gigabit Ethernet mode. Install the 10gigUpgrade license to enable new 10 Gigabit Ethernet ports in 10Gigabit Ethernet mode. To enable 1 Gigabit Ethernet mode, 1 Gigabit Ethernet SFPs have to be used on both the ends. There is no speed command to control the speed and this depends on the type of the SFP. The 10 Gigabit Ethernet ports does not support 100M speed. You can connect 10 Gigabit Ethernet SFP+ to 10 Gigabit Ethernet ports only.

Example: When 10gigUpgrade License is not Installed

The following error message appears when the 10gigUpgrade license is not installed and you use the show interface command:

Router# show interface Ten0/1

TenGigabitEthernet0/1 is down, line protocol is down (notconnect)

Hardware is TenGigabit Ethernet, address is 2c54.2dd6.c10e (bia 2c54.2dd6.c10e)

MTU 9216 bytes, BW 10000000 Kbit/sec, DLY 10 usec,

reliability 255/255, txload 1/255, rxload 1/255

	Encapsulation ARPA, loopback not set
	Keepalive set (10 sec)
	Unknown, Unknown, media type is H10GB-CU3M
	output flow-control is unsupported, input flow-control is unsupported
	LICENSE not available or 1G SFP ( Interface in 1G mode )
	ARP type: ARPA, ARP Timeout 04:00:00
	Last input never, output never, output hang never
	Last clearing of "show interface" counters never
	Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0
	Queueing strategy: fifo
	Output queue: 0/40 (size/max)
	5 minute input rate 0 bits/sec, 0 packets/sec
	5 minute output rate 0 bits/sec, 0 packets/sec
	0 packets input, 0 bytes, 0 no buffer
	Cisco ASR 901 Series Aggregation Services Router Software Configuration Guide
OL-23826-09		2-7