Chapter 10 Configuring Ethernet OAM

 

 

 

Command

 

Purpose

 

 

 

 

 

 

 

 

Step 7

service instance id ethernet [ser-

 

Creates a service instance (an instantiation of an EVC)

 

 

 

vice-name]

 

on an interface and sets the device into the config-if-srv

 

 

 

 

 

submode.

 

 

 

Example:

 

 

 

 

 

 

 

 

 

 

 

Router(config-if-srv)# service in-

 

 

 

 

 

 

 

 

 

 

 

stance 101 ethernet

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Step 8

encapsulation untagged dot1q vlan-id

 

Configures the encapsulation. Defines the matching

 

 

 

default

 

criteria that maps the ingress dot1q or untagged frames

 

 

 

 

 

on an interface for the appropriate service instance.

 

 

 

Example:

 

Effective with Cisco IOS Release 15.3(2)S, default

 

 

 

 

encapsulation is supported.

 

 

 

Router(config-if-srv)# encapsulation

 

 

 

 

dot1q 100

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Note

dot1q range and second-dot1q are not supported

 

 

 

 

 

 

 

for EFP Interface with Cross Connect.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Step 9

xconnect peer-ip-address vc-id {encap-

 

Binds an attachment circuit to a pseudowire, and

 

 

 

sulation {l2tpv3 [manual] mpls [man-

 

configures an Any Transport over MPLS (AToM) static

 

 

 

ual]} pw-class pw-class-name

 

pseudowire.

 

 

 

}[pw-class pw-class-name] [sequencing

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

{transmit receive both}]

 

 

 

 

 

 

 

 

 

 

 

Example:

 

 

 

 

 

 

 

 

 

 

 

Router(config-if-srv)# xconnect

 

 

 

 

 

 

 

 

 

 

 

10.0.3.201 123 pw-class vlan-xconnect

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Step 10

cfm mep domain domain-name [up down]

 

Configures a maintenance endpoint (MEP) for a domain.

 

 

 

mpid mpid-value [cos cos-value]

 

 

 

 

 

 

 

 

 

 

 

Example:

 

 

 

 

 

 

 

 

 

 

 

Router(config-if-srv)# cfm mep down

 

 

 

 

 

 

 

 

 

 

 

mpid 100 domain Core

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Step 11

exit

 

Exits the interface configuration mode.

 

 

 

Example:

 

 

 

 

 

 

 

 

 

 

 

Router(config-if-srv)# exit

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Examples

 

 

 

 

 

 

 

 

 

 

 

 

This example shows how to configure CFM over EVC using cross connect.

 

 

 

ASR901(config)#ethernet cfm ieee

 

 

 

 

 

 

 

 

 

 

ASR901(config)#ethernet cfm global

 

 

 

 

 

 

 

 

 

 

ASR901(config)#ethernet cfm domain L5 level 5

 

 

 

 

 

 

 

 

ASR901(config-ecfm)# service s1 evc e711

 

 

 

 

 

 

 

 

 

 

ASR901(config-ecfm-srv)# continuity-check

 

 

 

 

 

 

 

 

ASR901(config-ecfm-srv)#exit

 

 

 

 

 

 

 

 

 

 

ASR901(config-ecfm)#exit

 

 

 

 

 

 

 

 

 

 

Example for untagged Encapsulation

 

 

 

 

 

 

 

 

 

 

ASR901(config)#int g0/1

 

 

 

 

 

 

 

 

 

 

ASR901(config-if)#service instance 711 ethernet e711

 

 

 

Cisco ASR 901 Series Aggregation Services Router Software Configuration Guide

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

OL-23826-09

 

 

 

 

 

 

10-21

 

 

 

 

 

 

 

 

 

 

Page 191
Image 191
Cisco Systems A9014CFD manual Example for untagged Encapsulation, 10-21